Mistral MSF1679R User manual

STAND FAN
16” Stand Fan with Remote
MSF1679R

1
IMPORTANT SAFETY INSTRUCTIONS
Warning
•
•
•
•
•
•
•
•
Safety Instructions for Stand Fan
•
•
•
•
•
•
•
•
•
•
•
•
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge unless they have been
given supervision or instruction concerning the use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or has been dropped or damaged in any manner. If the power cord is
damaged, it must be replaced by the Service Centre to avoid a hazard.
When using electrical appliances, basic safety precautions should always be followed to
reduce the risk of re, electric shock, and/or injury.
Do not immerse appliance, cord or plug in water or other liquid.
Unplug from the outlet when not in use and before cleaning.
Do not unplug the appliance by pulling on the cord.
Use the accessories from the appliance only, as other accessories not from the appliance
may cause re, electric shock or injury.
Year 1 – 2 of use: It is recommended to switch o the fan and allow the motor to rest for at
least 1 hour after 10 hours of use.
After 2 Years of Use: It is recommended to switch o the fan and allow the motor to rest for
at least 1 hour after 3 hours of use.
For your own safety, please clean your fan regularly. Accumulation of dust/ pet dander etc.
may lead to motor re or pose a re hazard.
Do not cover the appliance or near ammable or explosive gases to avoid any re hazard.
The appliance must stand upright, it should have a distance of 30 cm other objects, or any
items would stop the oscillation of the appliance. Make sure there are no curtains, table
cloths, clothing, curtains, hair, etc. near the appliance. They could be sucked into the
opening of the fan, which can lead to damage or injury.
Do not insert your ngers, pencils, or any other objects into the appliance.
Do not use the appliance outdoors, or in any place where it can be splashed with oil, water,
or any substances. Do not expose the appliance to direct sunlight.
Do not use the appliance if it seems to be defective.
Do not let the appliance touch any hot surfaces.
Do not use the fan in high humidity, temperature, or dusty area.
Do not insert ngers or other objects into the fan during use.Avoid blowing the fan at
elderly and children for long periods of time.
Do not spray detergent such as insecticides into the fan to avoid damages to the material.

2
INTRODUCTION OF PARTS
PRODUCT TECHNICAL PARAMETERS
MSF1679R
MODEL
220-240V~, 50/60Hz
RATED VOLTAGE
55W
RATED POWER



















3
Assembly
•
•
•
•
CAUTION:
•
Unscrew the 7-shape Bolt from the Extension Pole. (Fig.1)
Insert the extension pole into the chassis and tighten the 7-shape Bolt (Fig.2)
From the extension pole loosen the height adjustment ring and adjust the internal pole to
the desired height. (Note: If you can’t nd the internal pole, it must inside the extension
pole. You can pull it out from the extension pole.) (Fig.3)
To attach the head unit to the internal pole, loosen the thumb screw on the bottom of the
head unit. Place the head unit on the internal pole and tighten the thumb screw in
alignment with the groove on the internal pole. (Fig.4)
Height adjustment ring must be fully fastened before the assembly of the
motor section to the internal pole.
CONTROLS AND OPERATIONS
Annulargroove
Mountinghole
Screw
Fig.3
Looseen
Fig.4
Fig.1Fig.2

4
Fan Blade Assembly
•
•
•
Remote Control
Power
•
•
Speed
•
Timer
•
•
•
•
Oscillation
•
Unscrew the spinner clockwise (or take the spinner out from the bag) and the plastic nut
counterclockwise to remove both of them. Fix the rear grill to the motor then tighten the
plastic nut again. (Fig. 5)
Insert the blade into shaft, and make sure the rotor shaft pin is tted into groove of the
blade. Turn the spinner counterclockwise to tighten the blade. (Fig. 6)
Fasten the front grill and the rear grill by the grill clip and then tighten the fan grill locking
screw and nut. (Fig. 7)
This button is for switching on the fan .The fan will be started at breeze step.
Press the button if the fan needs to switch o.
When the fan started, press this button repeated, the fan will work
with “0-1-2-3-4(O-Breeze-Low-Medium-High)” circulatory.
When this button is touched repeatedly or kept in pressed state, the time to be set for air
delivery increased step by step of each 0.5 hour and sums to 7.5 hours in 15 steps.
For instance, if the fan operation is required to be set for 5.5 hours,
this button must be touched repeatedly so that the pilot lamps for
0.5, 1 and 4 hours lighten together. It means that the set time is
0.5+ 1+ 4= 5.5 hours.
The time setting indicated by the pilot lamp will decrease gradually
by a unit of 0.5 hour.
Don’t press the TIMER key when the fan is required to operate
continuously. At the moment all pilot lamps don’t light.
After the fan is started, press this key to oscillate the fan, and
stop the oscillation at desired direction by pressing again. By
rotating the fan head by hand, you can get wider oscillation angle.
Fig.5
Spinner Spinner
Tight
Tight
Loose
Plastic nut
Slot
Retaining
Pin
Blade
Fig.6 Fig.7

5
Mode
•
Normal wind
•
Natural wind
•
•
Sleep Wind
•
•
Silent
•
•
•
•
Battery
•
1.
2.
3.
Notes:
•
Press this key to select mode. The sequence is normal, natural and sleep when this
key being touched repeatedly or continuously. The light can indicate mode state.
Press the mode button to select the normal wind, then press the “speed” repeatedly
to choose 3 speed.
Press the mode button to select the natural wind.
Natural wind is not adjustable.
Press the mode button to select the sleep wind.
Sleep wind is not adjustable.
In the state of non-silence, press silence button, the fan would be in silent state and
the silence icon is lightened, while the indicator icons of the other wind types and
wind levels would turn o.
In silent state, press wind type button, blast volume + and – buttons, there would be no
response, while other buttons could respond normally.
Press silence button again to quit and the fan would return to the previous working state.
The silence icon turns o and 00 is displayed on the digital screen.
Battery not included in the packing.
Slide the battery compartment Cover.
Insert the batteries, and make sure that the batteries are placed as shown in the Fig.10.
Slide back the battery cover.
Use size“AAA”manganese or alkaline batteries. Do not use rechargeable batteries.

6
Warning
•
•
•
How to use the remote control
•
•
•
Overheat motor protection
•
Control Panel
•
Tilt adjustment
•
Height adjustment
•
Power o/ memory
•
Do not dispose of batteries in re, batteries may explode or leak.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Point the remote controller at the receptor on body of the fan and press the desired button.
The remote controller will work at distances of up to roughly ve meters and the angle of
30 degree included between right and left from the receptor.
The batteries must be removed from the remote controller before it is scrapped and that
they are disposed of safely.
The windings of the motor have a thermal-fuse that burns out and the fan switches o and
temperature of the motor is no longer going up so that plastic parts of the fan don’t subject
to deformation so far so to be burned by the overheat if the motor is overheat for any
unexpected reason.
These keys of the control panel may be used as same as of the remote controller.
To adjust the air ow upward or downward, push the grilles lightly to the desired direction.
The height of the fan can be adjusted by loosening the height adjustment ring carefully
raising or lowering the fan and rmly re-tightening the height adjustment ring.
Fan shutdown or power o, the power is switched on again starts, will be operating in the
state of shutdown or power o (not before the timing function of memory).

7
CLEANING AND MAINTENANCECLEANING AND MAINTENANCE
The stand fan requires minimal maintenance. Do not try to x it by yourself.
•
•
•
•
•
•
•
•
Cleaning
•
•
Before cleaning and assembling, do not plug the power cord into the socket.
To ensure that there is adequate air circulation to the motor keep vents at the rear of the
motor housing from dust, u, etc.
Do not be used a vacuum cleaner to clean these vents before unplug.
Do not dissaemble the fan to remove u.
Please wipe the exterior parts with a soft cloth which is soaked in mild detergent.
Do not use any abrasive detergent or solvents to which may scratch the surface.
Do not use any of followings as cleaning agent: gasoline, thinner, bending.
Do not allow water or any other liquid into motor housing or interior parts.
Be sure to unplug the fan from the electrical supply mains before cleaning.
Plastic parts should be cleaned with a soft cloth moisten with mild soap. Thoroughly
remove soap lm with dry cloth.