Mistral MSF1835 Original instructions

5
e-Warranty Registration at https://mayecare.biz/eWarranty
Customer Service Hotline:[phone]
Mon-Fri:9:00am to 6:00pm
Sat:9:00am to 12noon
Closed:Sunday & Public Holidays
71 Ubi Crescent.#06-02.Excalibur Centre.Singapore 408571
Keep your sales receipt for future reference.
You must provide proof of purchase for in-warranty service.
If your product does not work properly because of a defect in materials or workmanship.
The warrantor will,for the length of the period indicated on chart below,which starts with
the date of original purchase(warranty period),at its option either(a) repair your product
with new or refurbished parts,(b) replace it with a new of a refurbished equivalent value
product,or (c) refund your purchase price.The decision to repair,replace or refund will be
made by the warrantor.
MSF1835

1、Front guard
8、Motor housing
2、Guard ring
9、Timer knob
3、Blade
4、Grille lock nut
5、Rear guard
7、Sway Tube
6、Motor shaft
12、Slide pipe
13、Connecting Rod
14、Stand
15、Base
10、Key switch
16、washer
17、7 shape bolt
11、Fan shell
18、Clip
12345
6
7
8
9
10
12
13
14
15
16
17
11
18
Follow the instructions below to install the fan. Keep the carton and shipping materials for future storage.
1.Installing the stand
① Remove the Washer(16) and 7 shape bolt(17) at the bottom of the stand(14).(see Figure 1)
②Insert the projection of the stand(14) into the groove of the base(15).(see Figure 2)
③Tighten the 7 shape bolt(17) to secure the stand(14) to the base (15). Use the Washer(16)for support.
(see figure 2)
Fig. 2
Fig. 1
2.Installing the main body
① Insert the slide pipe(12) into the hole of the fan shell(11).(see Figure 3 )
② Tighten the screw with a screwdriver.(see Figure 4)
3.Installing the rear guard
① Remove the grille lock nut(4) on the motor housing(8).
② Align each of 3 projections and 3 holes, then fix the rear guard(5) to the motor housing(8).
(see Figure 5)
③ Tighten the grille lock nut(4).(see Figure 6)
4.Installing the blade
①Align the slot on the motor shaft(6) with the screw on the blade(3). Tighten the screw with
a screwdriver.(see Figure 7)
Fig. 3 Fig. 4
Fig. 5 Fig. 6
Projections
Fig. 7
screw
slot

220-240～
50/60Hz
Timer knob When the fan is on,turn in clockwise
direction to the time you want the fan
turn off in automatically.
Key Switch Press 1,2or 3 to choose the desired
speed,Press 0 to turn off the fan.
Loosen the connecting rod(13) anticlockwise and
enable to adjust the height of slide pipe(12).
Tighten the connecting rod(13) clockwise after
adjusting to the desired height.
0
1
3
2
0------------OFF
2------------Med speed
3------------High speed
1------------low speed
SWAY Press sway tube(7) down to sway,
pull sway tube(7) up to stop sway.
60
20
ON
40
OFF
Appearance may vary
10
30
50
5.Installing the front guard
① Loosen the screw on the guard ring(2).(see Figure 8)
② Align the front guard(1) with the rear guard(5). Buckle the outer ting of the front guard(1) and the
rear guard(5) into the goove of the guard ring(2).(see Figure 9)
③ Tighten the guard ring screw.(see Figure 10)
④ Engage the clip.(see Figure 10)
Fig. 8 Fig. 9 Fig. 10

65W 55dB(A)
MSF1835
Energy Efficiency
3
1.58m / ( )min·W
Noise(SPL)
220-240V
50/60Hz