Mitsubishi Electric PUHY-HP72-240TNU-A Product guide

AIR CONDITIONING SYSTEMS
MODEL
PUHY-HP72-240T(S)NU-A
PUHY-HP72-240Y(S)NU-A

MEES21K108
GENERAL LINE-UP GENERAL LINE-UP
I.GENERAL LINE-UP
96K
PUHY-HP96YNU-A
120K
PUHY-HP120YNU-A
72K
PUHY-HP72YNU-A
Type(BTU/h)
Model Name
96K
PUHY-HP96TNU-A
120K
PUHY-HP120TNU-A
72K
PUHY-HP72TNU-A
Type(BTU/h)
Model Name
192K
PUHY-HP192YSNU-A
240K
PUHY-HP240YSNU-A
144K
PUHY-HP144YSNU-A
Type(BTU/h)
Model Name
192K
PUHY-HP192TSNU-A
240K
PUHY-HP240TSNU-A
144K
PUHY-HP144TSNU-A
Type(BTU/h)
Model Name
Hyper Heating Inverter Y-Series-208-230V Hyper Heating Inverter Y-Series-460V
0000006536.BOOK 1 ページ ２０２２年４月７日 木曜日 午後３時２０分

PUHY-HP-T(S)NU-A, PUHY-HP-Y(S)NU-A
MEES21K108 1
CONTENTS Hyper Heating Inverter Y-Series
I.Hyper Heating Inverter Y-Series
1. SPECIFICATIONS.................................................................................................................................... 2
2. EXTERNAL DIMENSIONS ....................................................................................................................... 14
3. CENTER OF GRAVITY ............................................................................................................................ 20
4. ELECTRICAL WIRING DIAGRAMS ......................................................................................................... 21
5. SOUND LEVELS ...................................................................................................................................... 23
5-1. Sound levels in cooling mode .......................................................................................................... 23
5-2. Sound levels in heating mode.......................................................................................................... 25
6. VIBRATION LEVEL .................................................................................................................................. 27
7. OPERATION TEMPERATURE RANGE................................................................................................... 28
8. CAPACITY TABLES ................................................................................................................................. 29
8-1. Selection of Cooling/Heating Units .................................................................................................. 30
8-2. Correction by temperature ............................................................................................................... 40
8-3. Correction by total indoor................................................................................................................. 64
8-4. Correction by refrigerant piping length............................................................................................. 67
8-5. Correction at frost and defrost ......................................................................................................... 69
8-6. Correction at evaporation-temperature (ET) control ........................................................................ 69
9. OPTIONAL PARTS................................................................................................................................... 70
9-1. JOINT .............................................................................................................................................. 70
9-2. HEADER.......................................................................................................................................... 71
9-3. OUTDOOR TWINNING KIT............................................................................................................. 72
9-4. FIN GUARD ..................................................................................................................................... 73
10.ELECTRICAL WORK ............................................................................................................................... 74
10-1.General cautions ............................................................................................................................. 74
10-2.Power supply for Outdoor unit ......................................................................................................... 75
10-3.Power cable specifications .............................................................................................................. 76
10-4.Power supply examples................................................................................................................... 77
11.M-NET CONTROL ................................................................................................................................... 79
11-1.Transmission cable length limitation................................................................................................ 79
11-2.Transmission cable specifications ................................................................................................... 80
11-3.System configuration restrictions..................................................................................................... 81
11-4.Address setting................................................................................................................................ 85
12.PIPING DESIGN ...................................................................................................................................... 95
12-1.R410A Piping material..................................................................................................................... 95
12-2.Piping Design .................................................................................................................................. 97
12-3.Refrigerant charging calculation ...................................................................................................... 100
13.OUTDOOR INSTALLATION .................................................................................................................... 103
13-1.General requirements for installation............................................................................................... 103
13-2.Spacing............................................................................................................................................ 104
13-3.Piping direction ................................................................................................................................ 106
13-4.Weather countermeasure ................................................................................................................ 111
13-5.Countermeasure to wind ................................................................................................................. 111
0000006537.BOOK 1 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
2
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
I.Hyper Heating Inverter Y-Series1. SPECIFICATIONS
Outdoor Model PUHY-HP72TNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 72,000
(Nominal) kW 21.1
Power input kW 5.39
(208-230) Current input A 16.6-15.0
(Rated) BTU/h 69,000
kW 20.2
Power input kW 4.90 5.07
(208-230) Current input A 15.1-13.6 15.6-14.1
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 80,000
(Nominal) kW 23.4
Power input kW 5.33
(208-230) Current input A 16.4-14.8
(Rated) BTU/h 76,000
kW 22.3
Power input kW 4.83 5.04
(208-230) Current input A 14.8-13.4 15.5-14.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P72/1~18
Sound pressure level (measured in anechoic room) *3 dB <A> 55.0/57.0
Sound power level (measured in anechoic room) *3 dB <A> 74.0/76.0
Refrigerant Liquid pipe in. (mm) 3/8 (9.52) Brazed
piping diameter Gas pipe in. (mm) 7/8 (22.2) Brazed
Minimum Circuit Ampacity A 38-35
Maximum Overcurrent Protection A 60-50
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 6,700
m3/min 190
L/s 3,170
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC
Starting method Inverter
Motor output kW 3.8 x 1
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 21 lbs + 10 oz (9.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 609 (276)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GM
Wiring KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS/102LS-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 2 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
3
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP96TNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 96,000
(Nominal) kW 28.1
Power input kW 6.23
(208-230) Current input A 19.2-17.3
(Rated) BTU/h 92,000
kW 27.0
Power input kW 5.71 5.82
(208-230) Current input A 17.6-15.9 17.9-16.2
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 108,000
(Nominal) kW 31.7
Power input kW 7.33
(208-230) Current input A 22.6-20.4
(Rated) BTU/h 103,000
kW 30.2
Power input kW 6.65 6.92
(208-230) Current input A 20.5-18.5 21.3-19.3
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~24
Sound pressure level (measured in anechoic room) *3 dB <A> 56.0/58.5
Sound power level (measured in anechoic room) *3 dB <A> 75.0/77.5
Refrigerant Liquid pipe in. (mm) 3/8 (9.52) Brazed (1/2 (12.7) Brazed, the farthest pipe length >= 90 m)
piping diameter Gas pipe in. (mm) 7/8 (22.2) Brazed
Minimum Circuit Ampacity A 43-40
Maximum Overcurrent Protection A 70-60
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 7,400
m3/min 210
L/s 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC
Starting method Inverter
Motor output kW 4.5 x 1
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 653 (296)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GM
Wiring KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS/102LS-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 3 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
4
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP120TNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 120,000
(Nominal) kW 35.2
Power input kW 8.53
(208-230) Current input A 26.3-23.7
(Rated) BTU/h 114,000
kW 33.4
Power input kW 7.67 8.11
(208-230) Current input A 23.6-21.3 25.0-22.6
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 135,000
(Nominal) kW 39.6
Power input kW 9.63
(208-230) Current input A 29.7-26.8
(Rated) BTU/h 129,000
kW 37.8
Power input kW 8.55 9.28
(208-230) Current input A 26.3-23.8 28.6-25.8
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~30
Sound pressure level (measured in anechoic room) *3 dB <A> 59.5/61.5
Sound power level (measured in anechoic room) *3 dB <A> 79.5/80.5
Refrigerant Liquid pipe in. (mm) 3/8 (9.52) Brazed (1/2 (12.7) Brazed, the farthest pipe length >= 40 m)
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Minimum Circuit Ampacity A 47-43
Maximum Overcurrent Protection A 70-60
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 7,750
m3/min 220
L/s 3,670
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC
Starting method Inverter
Motor output kW 6.5 x 1
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 655 (297)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GM
Wiring KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS/102LS-G2, CMY-Y202S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 4 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
5
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP144TSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 144,000
(Nominal) kW 42.2
Power input kW 12.20
(208-230) Current input A 37.6-34.0
(Rated) BTU/h 138,000
kW 40.4
Power input kW 10.98 11.61
(208-230) Current input A 33.8-30.6 35.8-32.3
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 160,000
(Nominal) kW 46.9
Power input kW 11.70
(208-230) Current input A 36.0-32.6
(Rated) BTU/h 152,000
kW 44.5
Power input kW 10.50 11.15
(208-230) Current input A 32.3-29.2 34.3-31.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~36
Sound pressure level (measured in anechoic room) *3 dB <A> 58.5/60.5
Sound power level (measured in anechoic room) *3 dB <A> 77.5/79.5
Refrigerant Liquid pipe in. (mm) 1/2 (12.7) Brazed
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PUHY-HP72TNU-A PUHY-HP72TNU-A
Minimum Circuit Ampacity A 38-35 38-35
Maximum Overcurrent Protection A 60-50 60-50
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 6,700 6,700
m3/min 190 190
L/s 3,170 3,170
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
Starting method Inverter Inverter
Motor output kW 3.8 x 1 3.8 x 1
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 21 lbs + 10 oz (9.8 kg) R410A x 21 lbs + 10 oz (9.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 609 (276) 609 (276)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe in. (mm) 3/8 (9.52) Brazed 3/8 (9.52) Brazed
distributor Gas pipe in. (mm) 7/8 (22.2) Brazed 7/8 (22.2) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GN
Wiring KE94G811 KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2, CMY-Y202S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 5 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
6
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP192TSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 192,000
(Nominal) kW 56.3
Power input kW 13.79
(208-230) Current input A 42.5-38.4
(Rated) BTU/h 184,000
kW 53.9
Power input kW 12.58 12.94
(208-230) Current input A 38.7-35.0 39.9-36.0
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 215,000
(Nominal) kW 63.0
Power input kW 15.91
(208-230) Current input A 49.0-44.3
(Rated) BTU/h 206,000
kW 60.4
Power input kW 14.39 15.06
(208-230) Current input A 44.3-40.1 46.4-42.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~48
Sound pressure level (measured in anechoic room) *3 dB <A> 59.5/62.0
Sound power level (measured in anechoic room) *3 dB <A> 78.5/81.0
Refrigerant Liquid pipe in. (mm) 5/8 (15.88) Brazed
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PUHY-HP96TNU-A PUHY-HP96TNU-A
Minimum Circuit Ampacity A 43-40 43-40
Maximum Overcurrent Protection A 70-60 70-60
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 7,400 7,400
m3/min 210 210
L/s 3,500 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
Starting method Inverter Inverter
Motor output kW 4.5 x 1 4.5 x 1
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 653 (296) 653 (296)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe in. (mm) 3/8 (9.52) Brazed 3/8 (9.52) Brazed
distributor Gas pipe in. (mm) 7/8 (22.2) Brazed 7/8 (22.2) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GN
Wiring KE94G811 KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2, CMY-Y202S/302S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 6 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
7
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP240TSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 240,000
(Nominal) kW 70.3
Power input kW 19.37
(208-230) Current input A 59.7-54.0
(Rated) BTU/h 228,000
kW 66.8
Power input kW 17.78 18.08
(208-230) Current input A 54.8-49.5 55.7-50.4
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 270,000
(Nominal) kW 79.1
Power input kW 21.38
(208-230) Current input A 65.9-59.6
(Rated) BTU/h 258,000
kW 75.6
Power input kW 19.48 20.10
(208-230) Current input A 60.0-54.3 61.9-56.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/2~50
Sound pressure level (measured in anechoic room) *3 dB <A> 63.0/65.0
Sound power level (measured in anechoic room) *3 dB <A> 83.0/84.0
Refrigerant Liquid pipe in. (mm) 5/8 (15.88) Brazed
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PUHY-HP120TNU-A PUHY-HP120TNU-A
Minimum Circuit Ampacity A 47-43 47-43
Maximum Overcurrent Protection A 70-60 70-60
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 7,750 7,750
m3/min 220 220
L/s 3,670 3,670
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
Starting method Inverter Inverter
Motor output kW 6.5 x 1 6.5 x 1
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 655 (297) 655 (297)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe in. (mm) 1/2 (12.7) Brazed 1/2 (12.7) Brazed
distributor Gas pipe in. (mm) 1-1/8 (28.58) Brazed 1-1/8 (28.58) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GN
Wiring KE94G811 KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2, CMY-Y202S/302S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 7 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
8
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP72YNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 72,000
(Nominal) kW 21.1
Power input kW 5.39
(460) Current input A 7.5
(Rated) BTU/h 69,000
kW 20.2
Power input kW 4.90 5.07
(460) Current input A 6.8 7.0
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 80,000
(Nominal) kW 23.4
Power input kW 5.33
(460) Current input A 7.4
(Rated) BTU/h 76,000
kW 22.3
Power input kW 4.83 5.04
(460) Current input A 6.7 7.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P72/1~18
Sound pressure level (measured in anechoic room) *3 dB <A> 55.0/57.0
Sound power level (measured in anechoic room) *3 dB <A> 74.0/76.0
Refrigerant Liquid pipe in. (mm) 3/8 (9.52) Brazed
piping diameter Gas pipe in. (mm) 7/8 (22.2) Brazed
Minimum Circuit Ampacity A 17
Maximum Overcurrent Protection A 25
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 6,700
m3/min 190
L/s 3,170
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC
Starting method Inverter
Motor output kW 3.8 x 1
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 21 lbs + 10 oz (9.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 644 (292)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GP
Wiring KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS/102LS-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 8 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
9
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP96YNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 96,000
(Nominal) kW 28.1
Power input kW 6.23
(460) Current input A 8.6
(Rated) BTU/h 92,000
kW 27.0
Power input kW 5.71 5.82
(460) Current input A 7.9 8.1
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 108,000
(Nominal) kW 31.7
Power input kW 7.33
(460) Current input A 10.2
(Rated) BTU/h 103,000
kW 30.2
Power input kW 6.65 6.92
(460) Current input A 9.2 9.6
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~24
Sound pressure level (measured in anechoic room) *3 dB <A> 56.0/58.5
Sound power level (measured in anechoic room) *3 dB <A> 75.0/77.5
Refrigerant Liquid pipe in. (mm) 3/8 (9.52) Brazed (1/2 (12.7) Brazed, the farthest pipe length >= 90 m)
piping diameter Gas pipe in. (mm) 7/8 (22.2) Brazed
Minimum Circuit Ampacity A 20
Maximum Overcurrent Protection A 30
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 7,400
m3/min 210
L/s 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC
Starting method Inverter
Motor output kW 4.5 x 1
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 688 (312)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GP
Wiring KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS/102LS-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 9 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
10
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP120YNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 120,000
(Nominal) kW 35.2
Power input kW 8.53
(460) Current input A 11.8
(Rated) BTU/h 114,000
kW 33.4
Power input kW 7.67 8.11
(460) Current input A 10.6 11.3
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 135,000
(Nominal) kW 39.6
Power input kW 9.63
(460) Current input A 13.4
(Rated) BTU/h 129,000
kW 37.8
Power input kW 8.55 9.28
(460) Current input A 11.9 12.9
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~30
Sound pressure level (measured in anechoic room) *3 dB <A> 59.5/61.5
Sound power level (measured in anechoic room) *3 dB <A> 79.5/80.5
Refrigerant Liquid pipe in. (mm) 3/8 (9.52) Brazed (1/2 (12.7) Brazed, the farthest pipe length >= 40 m)
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Minimum Circuit Ampacity A 21
Maximum Overcurrent Protection A 35
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 7,750
m3/min 220
L/s 3,670
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC
Starting method Inverter
Motor output kW 6.5 x 1
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 691 (313)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GP
Wiring KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS/102LS-G2, CMY-Y202S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 10 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
11
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP144YSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 144,000
(Nominal) kW 42.2
Power input kW 12.20
(460) Current input A 17.0
(Rated) BTU/h 138,000
kW 40.4
Power input kW 10.98 11.61
(460) Current input A 15.3 16.1
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 160,000
(Nominal) kW 46.9
Power input kW 11.70
(460) Current input A 16.3
(Rated) BTU/h 152,000
kW 44.5
Power input kW 10.50 11.15
(460) Current input A 14.6 15.5
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~36
Sound pressure level (measured in anechoic room) *3 dB <A> 58.5/60.5
Sound power level (measured in anechoic room) *3 dB <A> 77.5/79.5
Refrigerant Liquid pipe in. (mm) 1/2 (12.7) Brazed
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PUHY-HP72YNU-A PUHY-HP72YNU-A
Minimum Circuit Ampacity A 17 17
Maximum Overcurrent Protection A 25 25
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 6,700 6,700
m3/min 190 190
L/s 3,170 3,170
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
Starting method Inverter Inverter
Motor output kW 3.8 x 1 3.8 x 1
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 21 lbs + 10 oz (9.8 kg) R410A x 21 lbs + 10 oz (9.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 644 (292) 644 (292)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe in. (mm) 3/8 (9.52) Brazed 3/8 (9.52) Brazed
distributor Gas pipe in. (mm) 7/8 (22.2) Brazed 7/8 (22.2) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GQ
Wiring KE94G817 KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2, CMY-Y202S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 11 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
12
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP192YSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 192,000
(Nominal) kW 56.3
Power input kW 13.79
(460) Current input A 19.2
(Rated) BTU/h 184,000
kW 53.9
Power input kW 12.58 12.94
(460) Current input A 17.5 18.0
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 215,000
(Nominal) kW 63.0
Power input kW 15.91
(460) Current input A 22.1
(Rated) BTU/h 206,000
kW 60.4
Power input kW 14.39 15.06
(460) Current input A 20.0 21.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~48
Sound pressure level (measured in anechoic room) *3 dB <A> 59.5/62.0
Sound power level (measured in anechoic room) *3 dB <A> 78.5/81.0
Refrigerant Liquid pipe in. (mm) 5/8 (15.88) Brazed
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PUHY-HP96YNU-A PUHY-HP96YNU-A
Minimum Circuit Ampacity A 20 20
Maximum Overcurrent Protection A 30 30
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 7,400 7,400
m3/min 210 210
L/s 3,500 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
Starting method Inverter Inverter
Motor output kW 4.5 x 1 4.5 x 1
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 688 (312) 688 (312)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe in. (mm) 3/8 (9.52) Brazed 3/8 (9.52) Brazed
distributor Gas pipe in. (mm) 7/8 (22.2) Brazed 7/8 (22.2) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GQ
Wiring KE94G817 KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2, CMY-Y202S/302S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 12 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
13
1. SPECIFICATIONS Hyper Heating Inverter Y-Series
Outdoor Model PUHY-HP240YSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 240,000
(Nominal) kW 70.3
Power input kW 19.37
(460) Current input A 27.0
(Rated) BTU/h 228,000
kW 66.8
Power input kW 17.78 18.08
(460) Current input A 24.7 25.2
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 270,000
(Nominal) kW 79.1
Power input kW 21.38
(460) Current input A 29.8
(Rated) BTU/h 258,000
kW 75.6
Power input kW 19.48 20.10
(460) Current input A 27.1 28.0
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~130% of outdoor unit capacity
connectable Model/Quantity P04~P96/2~50
Sound pressure level (measured in anechoic room) *3 dB <A> 63.0/65.0
Sound power level (measured in anechoic room) *3 dB <A> 83.0/84.0
Refrigerant Liquid pipe in. (mm) 5/8 (15.88) Brazed
piping diameter Gas pipe in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PUHY-HP120YNU-A PUHY-HP120YNU-A
Minimum Circuit Ampacity A 21 21
Maximum Overcurrent Protection A 35 35
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 7,750 7,750
m3/min 220 220
L/s 3,670 3,670
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
Starting method Inverter Inverter
Motor output kW 6.5 x 1 6.5 x 1
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 3Y 7.8/1.1 or similar> <MUNSELL 3Y 7.8/1.1 or similar>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
devices Inverter circuit (COMP./FAN) Over-current protection Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control LEV and HIC circuit
Net weight lbs (kg) 691 (313) 691 (313)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) Copper pipe, tube-in-tube structure Copper pipe, tube-in-tube structure
Pipe between unit and Liquid pipe in. (mm) 1/2 (12.7) Brazed 1/2 (12.7) Brazed
distributor Gas pipe in. (mm) 1-1/8 (28.58) Brazed 1-1/8 (28.58) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GQ
Wiring KE94G817 KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2, CMY-Y202S/302S-G2
Header: CMY-Y104/108/1010C-G
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
Notes: Unit converter
1.Cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000006537.BOOK 13 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
14
2. EXTERNAL DIMENSIONS Hyper Heating Inverter Y-Series
2. EXTERNAL DIMENSIONS
PUHY-HP72, 96, 120TNU-A Unit: mm (in.)
Note 1.Please refer to the next page for information regarding necessary
spacing around the unit and foundation work.
2.At brazing of pipes, wrap the refrigerant service valve
with wet cloth and keep the temperature of refrigerant service valve under 120˚C(248°F).
740(29-3/16)
70(2-13/16)
150(5-15/16)
85(3-3/8)
85(3-3/8)
130(5-1/8)
150(5-15/16)
18(3/4)1204(47-7/16)18
1240(48-7/8)
110(4-3/8)
(740)(29-3/16)
185(7-5/16)
29.5
681(678~684)
29.5
94 79
181
160(6-5/16) 243(9-5/8)
150128(5-1/16)
125
132(5-1/4) 207(8-3/16) 256(10-1/8)
109
129(5-1/8)
84(3-5/16)
90(3-9/16)
54(2-3/16)
135(5-3/8)
20(13/16)
54
592(23-5/16)54(2-3/16)
20(13/16)
148(5-7/8)
152(6) 216(8-9/16)
166
144(5-11/16)
303
1515(59-11/16)
1818(71-5/8)
90(3-9/16)1060(41-3/4)90(3-9/16)
172(6-13/16)
(3-3/4) (3-1/8)
(5-15/16)
(6-9/16)
(7-3/16)
(26-13/16)(26-3/4~26-15/16)
(1-3/16)
(11-15/16)
(4-5/16)
(4-15/16)(2-3/16)
(3/4)
(1-3/16)
745(29-3/8)
(745)(29-3/8)
1250(49-1/4)
5(1/4)
5(1/4)
5
(1/4)
2
5
6
8
(Mounting pitch)
Bottom view
(Mounting pitch)
2×2-14(9/16)×20(13/16) Oval hole
1
Control box
3
4
7
Service panel
Intake
air
Intake
air
Discharge air
Intake
air Intake
air
2×6-ø4.6(3/16) Hole (Make hole at the plastic fan guard for snow hood attachment) <Snow hood attachment hole>
Top view
Front viewLeft side viewRear view
Refrigerant service valve <gas> Refrigerant service valve <liquid>
Refrigerant service valve <gas>
Refrigerant service valve <liquid>
Connecting pipe specifications
Diameter
Refrigerant pipe Service valve
ø12.7(1/2)
ø9.52(3/8) Brazed
ø28.58(1-1/8)
Liquid Gas Liquid Gas
ø28.58(1-1/8) Brazed
For transmission cables
For wires
For pipes
NO.
Usage Specifications
Front through hole Bottom through hole Front through hole Front through hole Bottom through hole Bottom through hole Front through hole
148(5-7/8)
×
84(3-5/16) Knockout hole
ø62.7(2-1/2) or ø34.5(1-3/8) Knockout hole ø43.7(1-3/4) or ø22.2(7/8) Knockout hole ø65(2-9/16) Knockout hole ø52(2-1/16) Knockout hole ø34(1-3/8) Knockout hole
150(5-15/16)
×
94(3-3/4) Knockout hole
ø34(1-3/8) Knockout holeBottom through hole
*1 Connect the refrigerant pipe to the service valve
according to the Installation Manual.
*2 Indicates dimensions and connection specifications
in the case the unit is used in combination with other outdoor units.
*3 Furthest piping length (OU from IU) ≥ 90m *4 Furthest piping length (OU from IU) ≥ 40m
(ø12.7(1/2) Brazed )*1,*3
ø9.52(3/8) Brazed
(ø12.7(1/2) Brazed )*1,*2,*4
Model
HP120
HP96 HP72
ø9.52(3/8) Brazed *1
ø22.2(7/8) Brazed *1
1 2 4 3 5 6 7 8
0000006537.BOOK 14 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
15
2. EXTERNAL DIMENSIONS Hyper Heating Inverter Y-Series
Unit: mm (in.)
PUHY-HP72, 96, 120TNU-A
●
In case of collective installation
1 When multiple units are installed adjacent to each other, secure enough space to allow
for air circulation and walkway between groups of units as shown in the figures below.
2 At least two sides must be left open. 3 As with the single installation, add the height that exceeds the height limit<h>
to the figures that are marked with an asterisk.
4 If there is a wall at both the front and the rear of the unit, install up to six units
consecutively in the side direction and provide a space of 1000mm(39-3/8) or more as inlet space/ passage space for each six units.
1 Take into consideration the surface strength, water drainage route,
piping route, and wiring route when preparing the installation site. <Note that the drain water comes out of the unit during operation.>
2 Build the foundation in such way that the corner of the installation leg is
securely supported as shown in the right figure.(Fig.A) When using a rubber isolating cushion, please ensure it is large enough to cover the entire width of each of the unit's legs.
3 The protrusion length of the anchor bolt must not exceed 30mm(1-3/16).(Fig.A) 4 Use four fixing plates as shown in the right figure <field supply required>
when using M12 hole-in anchor bolts <field supply required>.(Fig.B)
5 To prevent small animals and water and snow from entering the unit and damaging its parts,
close the gap around the edges of through holes for pipes and wires with filler plates <field supply required>.
6 When the pipes or cables are routed at the bottom of the unit,
make sure that the through hole at the base of the unit does not get blocked with the installation base.
7 Refer to the Installation Manual when installing units on an installation base.
2. Foundation work
1. Required space around the unit
●In case of single installation
<Wall height limit> Front : Up to the unit height
Back : Up to the unit height Side : Up to the unit height
Front
Unit height
H
Unit height
H
h
h
<Side view>
2 When the height of the walls on the front, back or on the sides<H>
exceeds the wall height limit as defined below add the height that exceeds the height limit <h> to the figures that are marked with an asterisk.
<Top view>
<Unit:mm(in)>
<Top view>
1 Secure enough space around the unit as shown in the figure below.
· With a space of at least
450mm(17-3/4) to the wall on the back of the unit
· With a space of at least
300mm(11-13/16) to the wall on the back of the unit
Front Front
30 min.* (1-3/16)
30 min.* (1-3/16)
450 min.*
(17-3/4)
450 min.*
(17-3/4)
300 min.*
(11-13/16)
450 min.* (17-3/4)
450 min.* (17-3/4)
450 min.*
(17-3/4)
M10 anchor bolt <field supply required>
Fixing plate <field supply required>
30mm max.
(1-3/16)
<To be left open>
Front
Wall <H>
<To be left open>
Front
<Unit:mm(in)>
Wall <H>
<To be left open>
<To be left open>
<To be left open>
Front
Wall <H>
Wall <H>
Wall <H>
Wall <H>
Front
Front
<To be left open>
Wall <H>
Front
Wall <H>
<To be left open>
<To be left open>
Front
Front
Front
Wall <H>
Wall <H>
Front
<To be left open>
<To be left open>
450 min. *
(17-3/4)
450 min. (17-3/4)
30 min. (1-3/16)
450 min. (17-3/4)
450 min.* (17-3/4)
450 min. (17-3/4)
300 min.* (11-13/16)
450 min. *
(17-3/4)
300 min.
*
(11-13/16)
450 min.
*
(17-3/4)
900 min.
450 min. *
(17-3/4)
900 min.
450 min. *
(17-3/4)
30 min.
*
(1-3/16)
(35-7/16)
(35-7/16)
1000 min.
*
(39-3/8)
450 min.
(17-3/4)
450 min.
(17-3/4)
Fig.A Fig.B
450 min.*
(17-3/4)
0000006537.BOOK 15 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
16
2. EXTERNAL DIMENSIONS Hyper Heating Inverter Y-Series
PUHY-HP144, 192, 240TSNU-A Unit: mm (in.)
Outdoor unit 2
Front view
Outdoor unit 1
Intake
air
Discharge air
c
b
To indoor unit
a
Liquid Twinning pipe <option parts>
e
To indoor unit
Gas Twinning pipe <option parts>
df
Left view
Intake
air
Intake
air
Intake
air
Note 1. Connect the pipes as shown in the figure above. Refer to the table above for the pipe size.
2. Twinning pipes should not be tilted more than 15 degrees from the horizontal plane. Be sure to see the Installation Manual for details of Twinning pipe installation. 3. The pipe section before the Twinning pipe (section ″a″ and ″b″ in the figure) must have at least 500mm(19-11/16) of straight section (*including the straight pipe that is supplied with the Twinning pipe). 4. Only use the Twinning pipe by Mitsubishi (optional parts).
Twinning pipe connection size
ø28.58(1-1/8)
CMY-Y100CBK3
PUHY-HP144TSNU-A
PUHY-HP72TNU-A PUHY-HP72TNU-A
PUHY-HP192TSNU-A
PUHY-HP96TNU-A
PUHY-HP240TSNU-A Gas
d or f
Liquid
c or e
Unit model
Twinning pipe~Outdoor unit
HP96 HP120
ø28.58(1-1/8)
a b
Liquid
Gas
Component unit name
Outdoor unit 1
Package unit name Outdoor Twinning Kit(optional parts)
BC controller
~Twinning pipe
Outdoor unit 2
PUHY-HP96TNU-A PUHY-HP120TNU-A
PUHY-HP120TNU-A
ø15.88(5/8) ø12.7(1/2)
HP72 ø9.52(3/8) ø22.2(7/8)
ø12.7(1/2)
740(29-3/16) 1240(48-7/8)
1818(71-5/8)
1240(48-7/8)
30(1-3/16)
5(1/4)5(1/4)
1250(49-1/4) 1250(49-1/4)745(29-3/8)
5(1/4)
0000006537.BOOK 16 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
17
2. EXTERNAL DIMENSIONS Hyper Heating Inverter Y-Series
PUHY-HP72, 96, 120YNU-A Unit: mm (in.)
1 2 4 3 5 6 7 8
Note 1.Please refer to the next page for information regarding necessary
spacing around the unit and foundation work.
2.At brazing of pipes, wrap the refrigerant service valve
with wet cloth and keep the temperature of refrigerant service valve under 120˚C(248°F).
2
5
6
8
(Mounting pitch)
Bottom view
(Mounting pitch)
2×2-14(9/16)×20(13/16) Oval hole
1
Control box
3
4
7
Service panel
Intake
air
Intake
air
Discharge air
Intake
air Intake
air
2×6-ø4.6(3/16) Hole (Make hole at the plastic fan guard for snow hood attachment)
<Snow hood attachment hole>
Top view
Front view
Left side view
Rear view
Refrigerant service valve <gas> Refrigerant service valve <liquid>
Refrigerant service valve <gas>
Refrigerant service valve <liquid>
Transformer box
Connecting pipe specifications
Diameter
Refrigerant pipe Service valve
ø12.7(1/2)
ø9.52(3/8) Brazed
ø28.58(1-1/8)
Liquid Gas Liquid Gas
ø28.58(1-1/8) Brazed
For transmission cables
For wires
For pipes
NO.
Usage Specifications
Front through hole Bottom through hole Front through hole Front through hole Bottom through hole Bottom through hole Front through hole
148(5-7/8)
×
84(3-5/16) Knockout hole
ø62.7(2-1/2) or ø34.5(1-3/8) Knockout hole ø43.7(1-3/4) or ø22.2(7/8) Knockout hole ø65(2-9/16) Knockout hole ø52(2-1/16) Knockout hole ø34(1-3/8) Knockout hole
150(5-15/16)
×
94(3-3/4) Knockout hole
ø34(1-3/8) Knockout holeBottom through hole
*1 Connect the refrigerant pipe to the service valve
according to the Installation Manual.
*2 Indicates dimensions and connection specifications
in the case the unit is used in combination with other outdoor units.
*3 Furthest piping length (OU from IU) ≥ 90m *4 Furthest piping length (OU from IU) ≥ 40m
(ø12.7(1/2) Brazed )*1,*3 ø9.52(3/8) Brazed (ø12.7(1/2) Brazed )*1,*2,*4
Model
HP120
HP96 HP72
ø9.52(3/8) Brazed *1
ø22.2(7/8) Brazed *1
740(29-3/16)
70(2-13/16)
150(5-15/16)
85(3-3/8)
85(3-3/8)
130(5-1/8)
150(5-15/16)
18(3/4)1204(47-7/16)18
1240(48-7/8)
110(4-3/8)
(740)(29-3/16)
185(7-5/16)
29.5681(678~684)29.5
94 79
181
160(6-5/16)
243(9-5/8)
150
128(5-1/16)
125
132(5-1/4) 207(8-3/16) 256(10-1/8)
109
129(5-1/8)
84(3-5/16)
90(3-9/16)
54(2-3/16)
135(5-3/8)
20(13/16)
54
592(23-5/16)54(2-3/16)
20(13/16)
148(5-7/8)
152(6)
216(8-9/16)
166
144(5-11/16)
303
1515(59-11/16)
1818(71-5/8)
90(3-9/16)1060(41-3/4)90(3-9/16)
172(6-13/16)
(3-3/4) (3-1/8)
(5-15/16)
(6-9/16)
(7-3/16)
(26-13/16 )(26-3/4~26-15/16)
(1-3/16)
(11-15/16)
(4-5/16)
(4-15/16)
(2-3/16)
(3/4)
(1-3/16)
745(29-3/8)
(745)(29-3/8)
1250(49-1/4)
5(1/4)
5(1/4)
5
(1/4)
0000006537.BOOK 17 ページ ２０２２年４月１４日 木曜日 午前１０時４１分

MEES21K108
PUHY-HP-T(S)NU-A, Y(S)NU-A
18
2. EXTERNAL DIMENSIONS Hyper Heating Inverter Y-Series
Unit: mm (in.)
PUHY-HP72, 96, 120YNU-A
●
In case of collective installation
1 When multiple units are installed adjacent to each other, secure enough space to allow
for air circulation and walkway between groups of units as shown in the figures below.
2 At least two sides must be left open. 3 As with the single installation, add the height that exceeds the height limit<h>
to the figures that are marked with an asterisk.
4 If there is a wall at both the front and the rear of the unit, install up to six units
consecutively in the side direction and provide a space of 1000mm(39-3/8) or more as inlet space/ passage space for each six units.
2. Foundation work
1. Required space around the unit
●In case of single installation
<Wall height limit> Front : Up to the unit height
Back : Up to the unit height Side : Up to the unit height
Front
Unit height
H
Unit height
H
h
h
<Side view>
2 When the height of the walls on the front, back or on the sides<H>
exceeds the wall height limit as defined below add the height that exceeds the height limit <h> to the figures that are marked with an asterisk.
<Top view>
<Unit:mm(in)>
<Top view>
1 Secure enough space around the unit as shown in the figure below.
· With a space of at least
450mm(17-3/4) to the wall on the back of the unit
· With a space of at least
300mm(11-13/16) to the wall on the back of the unit
Front Front
30 min.* (1-3/16)
30 min.* (1-3/16)
450 min.*
(17-3/4)
450 min.*
(17-3/4)
300 min.*
(11-13/16)
450 min.* (17-3/4)
450 min.* (17-3/4)
450 min.*
(17-3/4)
M10 anchor bolt <field supply required>
Fixing plate <field supply required>
30mm max.
(1-3/16)
<To be left open>
Front
Wall <H>
<To be left open>
Front
<Unit:mm(in)>
Wall <H>
<To be left open>
<To be left open>
<To be left open>
Front
Wall <H>
Wall <H>
Wall <H>
Wall <H>
Front
Front
<To be left open>
Wall <H>
Front
Wall <H>
<To be left open>
<To be left open>
Front
Front
Front
Wall <H>
Wall <H>
Front
<To be left open>
<To be left open>
450 min. *
(17-3/4)
450 min. (17-3/4)
30 min. (1-3/16)
450 min. (17-3/4)
450 min.* (17-3/4)
450 min. (17-3/4)
300 min.* (11-13/16)
450 min. *
(17-3/4)
300 min.
*
(11-13/16)
450 min.
*
(17-3/4)
900 min.
450 min. *
(17-3/4)
900 min.
450 min. *
(17-3/4)
30 min.
*
(1-3/16)
(35-7/16)
(35-7/16)
1000 min.
*
(39-3/8)
450 min.
(17-3/4)
450 min.
(17-3/4)
Fig.A Fig.B
450 min.*
(17-3/4)
1 Take into consideration the surface strength, water drainage route,
piping route, and wiring route when preparing the installation site. <Note that the drain water comes out of the unit during operation.>
2 Build the foundation in such way that the corner of the installation leg is
securely supported as shown in the right figure.(Fig.A) When using a rubber isolating cushion, please ensure it is large enough to cover the entire width of each of the unit's legs.
3 The protrusion length of the anchor bolt must not exceed 30mm(1-3/16).(Fig.A) 4 Use four fixing plates as shown in the right figure <field supply required>
when using M12 hole-in anchor bolts <field supply required>.(Fig.B)
5 To prevent small animals and water and snow from entering the unit and damaging its parts,
close the gap around the edges of through holes for pipes and wires with filler plates <field supply required>.
6 When the pipes or cables are routed at the bottom of the unit,
make sure that the through hole at the base of the unit does not get blocked with the installation base.
7 Refer to the Installation Manual when installing units on an installation base.
0000006537.BOOK 18 ページ ２０２２年４月１４日 木曜日 午前１０時４１分