Mitsubishi Electric MR-J5-G Series User manual

MR-J5-G/MR-J5W-G
User's Manual
(Communication Function)
-MR-J5-_G_
-MR-J5W_-_G_
-MR-J5D_-_G_
Mitsubishi Electric AC Servo System

1
SAFETY INSTRUCTIONS
Please read the instructions carefully before using the equipment.
To use the equipment correctly, do not attempt to install, operate, maintain, or inspect the equipment until you have read
through this manual, installation guide, and appended documents carefully. Do not use the equipment until you have a full
knowledge of the equipment, safety information and instructions.
In this manual, the safety instruction levels are classified into "WARNING" and "CAUTION".
Note that the CAUTION level may lead to a serious consequence depending on conditions.
Please follow the instructions of both levels because they are important to personnel safety.
Forbidden actions and required actions are indicated by the following diagrammatic symbols.
In this manual, precautions for hazards that can lead to property damage, instructions for other functions, and other
information are shown separately in the "POINT" area.
After reading this manual, keep it accessible to the operator.
WARNING
Indicates that incorrect handling may cause hazardous conditions, resulting in
death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions, resulting in
medium or slight injury.
Indicates a forbidden action. For example, "No Fire" is indicated by .
Indicates a required action. For example, grounding is indicated by .

2
[Installation/wiring]
[Setting/adjustment]
[Operation]
[Maintenance]
WARNING
●To prevent an electric shock, turn off the power and wait for 15 minutes or more (20 minutes or more
for the converter unit/drive unit) before starting wiring and/or inspection.
●To prevent an electric shock, ground the servo amplifier.
●To prevent an electric shock, any person who is involved in wiring should be fully competent to do the
work.
●To prevent an electric shock, mount the servo amplifier before wiring.
●To prevent an electric shock, connect the protective earth (PE) terminal of the servo amplifier to the
protective earth (PE) of the cabinet, then connect the grounding lead wire to the ground.
●To prevent an electric shock, do not touch the conductive parts.
WARNING
●To prevent an electric shock, do not operate the switches with wet hands.
WARNING
●To prevent an electric shock, do not operate the switches with wet hands.
WARNING
●To prevent an electric shock, any person who is involved in inspection should be fully competent to do
the work.
●To prevent an electric shock, do not operate the switches with wet hands.

3
ABOUT THE MANUAL
e-Manuals are Mitsubishi Electric FA electronic book manuals that can be browsed with a dedicated tool.
e-Manuals enable the following:
• Searching for desired information in multiple manuals at the same time (manual cross searching)
• Jumping from a link in a manual to another manual for reference
• Browsing for hardware specifications by scrolling over the components shown in product illustrations
• Bookmarking frequently referenced information
• Copying sample programs to engineering tools
If using the servo for the first time, prepare and use the following related manuals to ensure that the servo is used safely. For
the related manuals, refer to the User's Manual (Introduction).
When reading this manual to use a drive unit, substitute "drive unit" for "servo amplifier".
Rotary Servo Motor
Linear Servo Motor
Direct Drive Motor
This manual is necessary primarily for installing, wiring, and
using options.
The manual is necessary for operation of servo amplifiers.
The manual is necessary for adjustment of operation status.
The manual is necessary for using communication functions.
The manual is necessary for specifying the causes of alarms
and warnings.
Partner Encoder
Function
Adjustment
Object Dictionary
Troubleshooting
Introduction
Hardware
Communication Function
Parameters It describes the parameters of the servo amplifier.
It describes the objects for the servo amplifier.
For the usage of each function, refer to this manual.

4
OBJECT UNITS
This section explains the pos units, vel units, and acc units used in this manual.
The degree unit is available on servo amplifiers with firmware version B6 or later.
The mm unit and inch unit are available on servo amplifiers with firmware version B8 or later in the positioning mode (point
table method).
pos units
The standard unit can be changed using [Pr. PT01.2 Unit for position data] as shown in the following table.
vel units
The speed unit can be changed using [Pr. PT01.1 Speed/acceleration/deceleration unit selection] as shown in the following
table. The command unit can be changed to "0.001 mm", "0.0001 inch", "0.001 degree", or "pulse" using [Pr. PT01.2].
*1 0.01 mm/s is used in the linear servo motor control mode.
acc units
The acceleration unit can be changed using [Pr. PT01.1] as shown in the following table. The command unit can be changed
to "0.001 mm", "0.0001 inch", "0.001 degree", or "pulse" using [Pr. PT01.2].
U.S. CUSTOMARY UNITS
U.S. customary units are not shown in this manual. Convert the values if necessary according to the following table.
Setting value Standard unit
0mm
1inch
2 degree
3 pulse
Setting value Unit
0 0.01 r/min, 0.01 mm/s *1
1 Command unit/s
Setting value Unit
0ms
1 Command unit/s2
Quantity SI (metric) unit U.S. customary unit
Mass 1 [kg] 2.2046 [lb]
Length 1 [mm] 0.03937 [inch]
Torque 1 [N•m] 141.6 [oz•inch]
Moment of inertia 1 [(× 10-4 kg•m2)] 5.4675 [oz•inch2]
Load (thrust load/axial load) 1 [N] 0.2248 [lbf]
Temperature N [°C] × 9/5 + 32 N [°F]

5
CONTENTS
CONTENTS
SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
ABOUT THE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
OBJECT UNITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
U.S. CUSTOMARY UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
CHAPTER 1 CC-Link IE TSN 7
1.1 Functions and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
System configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Function list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Communication specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Establishing and disconnecting the communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Summary of object dictionary (OD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Engineering tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CC-Link IE TSN Class A settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.3 Application function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CC-Link IE TSN Network diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
IP address setting function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parameter automatic setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hold/Clear of output at CPU STOP and at CPU stop error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Remote reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Master-slave operation function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Clock function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Motion mode (high-speed) setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
1.4 APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CC-Link IE TSN communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cyclic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Transient transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Drive profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Setting of positioning data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
CHAPTER 2 CC-Link IE Field Network Basic 79
2.1 Functions and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
System configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Function list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Communication specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Establishing and disconnecting the communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Summary of object dictionary (OD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Engineering tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
2.2 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
2.3 Application function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
CC-Link IE Field Network Basic Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

6
IP address setting function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Hold/Clear of output at CPU STOP and at CPU stop error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Remote reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
2.4 APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Cyclic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
SLMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Drive profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132

1 CC-Link IE TSN
1.1 Functions and configuration 7
1
1CC-Link IE TSN
1.1 Functions and configuration
This manual describes communication with the MR-J5_-_G_ servo amplifiers using CC-Link IE TSN. In addition to this
manual, refer to the following manual when using CC-Link IE TSN.
MR-J5-G/MR-J5W-G User's Manual (Object Dictionary)
Outline
Motion mode
Motion mode is used with a controller supported by a CANopen profile. Combining with Mitsubishi Electric manufactured
Motion modules enables advanced motion control such as positioning of multiple axes, synchronous control by sequential
command or interpolation control. The positioning function built-in servo amplifier can be used for positioning operation.
Motion mode supports CiA 402 drive profile.
Refer to the following for control modes supported by motion mode.
Page 8 Function list
Page 75 Control mode
System configuration
Compatible controller
*1 Combine the module with the servo amplifier that has firmware version B9 or later.
Category Model
Motion module RD78G
RD78GH
FX5-_SSC-G *1
Master/local module RJ71GN11-T2 *1
Motion Control Software SWM-G

81 CC-Link IE TSN
1.1 Functions and configuration
Function list
Communication-related function list (Application)
Category Subcategory Function Description Detailed explanation
Network Open network CC-Link IE TSN
communication protocol
This servo amplifier supports CC-Link IE TSN. Page 9
Communication
specifications
CC-Link IE TSN
communication setting
Network configuration settings and station-specific mode selection
are performed by using GX Works3.
Page 13 Startup
Common
protocol
SLMP This function supports SLMP (SeamLess Message Protocol).
Parameter setting and monitoring are enabled.
Page 38 CC-Link IE
TSN communication
protocol
Profile CSP+ File for describing the necessary information for startup, operation,
and maintenance of CC-Link family connected products.

Application
function
Functional
safety
Safety communication
function
Connecting the servo amplifier with a programmable controller that
supports functional safety enables safety sub-functions.
MR-J5 User's Manual
(Hardware)
MR-J5D User's
Manual (Hardware)
MR-J5 User's Manual
(Function)
Cyclic
transmission
Hold/Clear of output at
CPU STOP and CPU
stop error
When the CPU module of the cyclic master is at STOP, when the
stop error occurs, Hold/Clear is automatically set on the refresh
device output. The servo amplifier stops regardless of the setting of
Hold/Clear of the cyclic master.
Page 19 Hold/Clear
of output at CPU STOP
and at CPU stop error
RAS function Automatic return When a station that has been disconnected due to a data link error
becomes normal, that particular station will automatically reconnect
to the network, and restart the data link.

Synchronization CC-Link IE TSN network
synchronous
communication function
The control cycle of the device station can be synchronized via the
CC-Link IE TSN in accordance with the synchronization cycle
specified by the master station. Thus, operation timing of other
device stations connected to the same network can be
synchronized.

Motion mode (high-
speed)
The communication cycle between the master station and the
device station can be set to 31.25 μs.
Page 37 Motion
mode (high-speed)
setting
Master-slave operation
function
This function transmits the torque and speed of the master axis to a
slave axis through driver communication, and controls and
operates the slave axis using the transmitted torque and speed as
commands.
This function can be used only on 1-axis servo amplifiers.
Page 20 Master-
slave operation function
Network system
startup
Detect Now function The master station reads the information (a model code, a device
version, etc.) of the servo amplifier that is connected to the network
and automatically sets the network configuration.

Station mode check The master station checks whether the master station and the
servo amplifier are in the same station mode by obtaining the
station mode of the servo amplifier.

Parameter
setting
Parameter automatic
setting
This is a function where the controller automatically writes the servo
parameters when the servo amplifier is returning/entering.
Page 18 Parameter
automatic setting
Setting change Remote reset This is a function to reset a servo amplifier via the network. Servo
parameters to be enabled at power cycle are reflected by resetting
the servo amplifier.
Page 19 Remote
reset
IP address setting IP addresses are delivered from the controller to servo amplifiers
via CC-Link IE TSN.
Page 17 IP address
setting function
CC-Link IE TSN
Network
diagnostics
Reserved station
specification/cancellation
Stations not connected to the network can be included in the total
number of stations for future connection.
Page 16 CC-Link IE
TSN Network diagnostics
Time
synchronization
Clock function This function is used to acquire time information from the grand
master (the station serving as a clock source) via CC-Link IE TSN
so that this information may be used for the time management of
functions performed by the servo amplifier, such as alarm history.
Page 37 Clock
function

1 CC-Link IE TSN
1.1 Functions and configuration 9
1
Communication specifications
Communication specifications of CC-Link IE TSN
Item Description Remark
Physical layer 1000BASE-T (1 Gbps), 100BASE-TX (100 Mbps) Twisted pair
Communication connector RJ-45 × 2 
Communication
cable
Cable type Category 5e or higher, (double shielded/STP) straight cable 
Standard One of the following standards must be met.
• IEEE802.3 1000BASE-T
• ANSI/TIA/EIA-568-B (Category 5e)
Connector RJ-45 shielded connector
Network topology Line, tree (star) 
Communication speed 1 Gbps, 100 Mbps *3 
Transmission distance between stations Max. 100 m 
Number of connection nodes Max. 254 stations The number of connection nodes depends on
the specifications of the controller.
Guaranteeing method of communication
bandwidth
Time division 
CC-Link IE TSN Class Class B/A *5 For Class A, refer to the following.
Page 15 CC-Link IE TSN Class A settings
CC-Link IE TSN protocol version Class B ver. 1.0/2.0 *5
Class A ver. 2.0 *5

Maximum response time in the time-
managed polling method (for CC-Link IE
TSN Class A)
512 μs
Synchronization method IEEE802.1AS, IEEE1588 
Communication
cycle *1*2*4*6
MR-J5-_G_
MR-J5D1-_G_
31.25 μs, 62.5 μs, 125 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms,
8 ms
When setting the communication cycle to 31.25
μs, refer to the following.
Page 37 Motion mode (high-speed) setting
MR-J5W2-_G
MR-J5D2-_G_
62.5 μs, 125 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms 
MR-J5W3-_G 125 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms 
MR-J5D3-_G_ 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms 
Cyclic transmission [Motion mode]
Communicates data cyclically between stations using PDOs.
• Maximum RPDO size: 80 bytes/axis
• Maximum TPDO size: 80 bytes/axis
• The servo amplifiers support variable PDO mapping.
Page 40 Cyclic transmission
Page 45 PDO mapping objects
Transient transmission [Motion mode]
Communicates data non-cyclically between stations using
SLMP and other protocols. SDOs can be used to read and
write objects of the servo amplifier.
Page 52 Transient transmission
Port No. No. 161: For system use
No. 5010: SLMP communication port (UDP/IP)
No. 45237: For system use
No. 45238: For system use
No. 45239: For system use


10 1 CC-Link IE TSN
1.1 Functions and configuration
*1 The communication cycle depends on the controller specifications and the number of the connected axes. The communication cycles of
31.25 μs and 62.5 μs can be used by servo amplifiers with firmware version A6 or later.
*2 There are restrictions on the communication cycle depending on the function used. For details, refer to "CC-Link IE TSN restrictions" in
the following manual.
MR-J5-G/MR-J5W-G User's Manual (Introduction)
MR-J5D-G User's Manual (Introduction)
*3 The communication speed can be set to 1 Gbps or 100 Mbps. 100 Mbps can be used with servo amplifiers with firmware version B6 or
later. When 100 Mbps is selected, the minimum communication cycle is 500 μs. When using 100 Mbps, set [Pr. NPA12 Communication
speed] to "1h". For details, refer to "Network basic parameters" in the following manual.
MR-J5-G/MR-J5W-G User's Manual (Parameters)
*4 Multiple communication cycles can be set with servo amplifiers with firmware version D0 or later. When using a servo amplifier with a
firmware version earlier than D0, set the communication cycle to "Basic Period". For details, refer to the manual for the master station
being used.
*5 "Class B ver. 2.0" and "Class A ver. 2.0" can be selected by servo amplifiers with firmware version D0 or later.
*6 For Class A, set the communication cycle to a value between 500 μs and 500 ms inclusive.

1 CC-Link IE TSN
1.1 Functions and configuration 11
1
Establishing and disconnecting the communication
Establishing the communication
Configure the system and set the parameters or rotary switches that are required for startup of the CC-Link IE TSN master
station and the servo amplifier. The communication will be established if the settings of the master station and the servo
amplifiers are made correctly. When the communication is established, the 7-segment LED display of the servo amplifiers
changes to "controller is connected".
Disconnecting the communication
■Procedure for disconnecting the communication
When shutting off the system power or disconnecting the servo amplifier from the network, be sure to disconnect after servo-
off. Failing to do so may trigger [AL. 086 Network communication error].
■Changing the communication configuration
Make sure that the servo amplifier is in servo-off state before changing the network configuration. Failing to do so may trigger
[AL. 086].
Summary of object dictionary (OD)
The data that a device holds, such as control parameters, command values, and feedback values, is handled as an object
composed of an Index, object name, object type, R/W attribute, and other elements. The data is exchanged between the
master and device stations. The aggregate of these objects is called an object dictionary (OD).
Section definition of object dictionary
The following shows the structure of an object dictionary. Each axis (Axes A, B, and C) of 1-axis servo amplifier and multi-axis
servo amplifier has the same object dictionary configuration.
The classification of the objects defined by Mitsubishi Electric is as follows.
Index Description Reference
1000h to 1FFFh Communication profile MR-J5-G/MR-J5W-G User's Manual (Object
Dictionary)
2000h to 5FFFh Objects group defined by Mitsubishi Electric
6000h to 9FFFh CiA 402 drive profile
Index Description Reference
2000h to 27FFh Servo parameter MR-J5-G/MR-J5W-G User's Manual (Object
Dictionary)
2800h to 29FFh Point table
2A00h to 2A7Fh Alarm
2B00h to 2BFFh Monitor
2C00h to 2C7Fh Diagnostics
2D00h to 2DFFh Manufacturer defined control Page 62 Controlword/Control DI
Page 68 Statusword/Status DO

12 1 CC-Link IE TSN
1.1 Functions and configuration
Saving object dictionary data
Some of object dictionary data is stored in a non-volatile memory and some is not. Use [Store parameters (Obj. 1010h)] for
storing the object dictionary data in the non-volatile memory.
For details about objects that can be stored in the non-volatile memory, refer to the following manual.
MR-J5-G/MR-J5W-G User's Manual (Object Dictionary)
■Store parameters
Writing "65766173h" (= reverse order of the ASCII code "save") to [Save all parameters (Obj. 1010h: 01h)] enables the setting
value of an object to be stored in the non-volatile memory of the servo amplifier.
It can take up to around 25 s for [Save all parameters (Obj. 1010h: 01h)] to write all the parameters. Do not shut off the power
supply during writing.
Reading [Save all parameters (Obj. 1010h: 01h)] returns any of the following values. Bit 0 is "0" during saving and "1" when
not saving.
• To shut off the power supply after executing Store parameters, make sure that a save is not in progress (Bit
0 is on), then shut off the power.
■Restore default parameters
Objects can be reset to the factory setting.
To initialize objects, write "64616F6Ch" (= reverse order of the ASCII code "load") to [Restore all default parameters (Obj.
1011h: 01h)], then cycle the power. Writing a value other than "load" (= 64616F6Ch) triggers an error. Initialization can take up
to around 25 s.
Reading [Restore all default parameters (Obj. 1011h: 01h)] displays "00000001h" (initializing values).
Engineering tool
The following explains the main purposes of the engineering tools used in communication. For specific usages, refer to the
manuals of the engineering tool and controller.
Engineering tool list
This list shows engineering tools used in CC-Link IE TSN.
Index Sub Object Name Data Type Access Description
1010h 0 ARRAY Store parameters U8 ro Number of entries
1 Save all parameters U32 rw Saves all parameters.
Bit Description
0 0: Object cannot be saved by the command (save in progress)
1: Object can be saved by the command (save not in progress)
1 0: Not automatically saved
Index Sub Object Name Data Type Access Description
1011h 0 ARRAY Restore default parameters U8 ro Number of entries
1 Restore all default parameters U32 rw All parameter initialization
Engineering tool Description
MR Configurator2 This is a software that has the following functions: servo amplifier adjustment, monitor display, diagnosis,
reading/writing of servo parameters, and test operation.
Settings, such as a stroke limit, absolute position detection system, communication error detection time, are
made with this software.
If using MR Configurator2 via a network, start MR Configurator2 from GX Works3. The servo amplifier and the
personal computer do not need to be connected with a USB cable because they communicate each other via the
controller.
GX Works3 This is a software that comprehensively supports the design and maintenance of the programmable controllers.
The software performs settings such as servo amplifier profile (CSP+) registration, network configuration setting
(station specific mode, link device setting, etc.), refresh setting, and network synchronization setting.

1 CC-Link IE TSN
1.2 Startup 13
1
1.2 Startup
Outline
This chapter describes the setting procedure for CC-Link IE TSN. Refer to the following manual for startup of the servo
amplifier.
MR-J5-G/MR-J5W-G User's Manual (Introduction)
MR-J5D-G User's Manual (Introduction)
• To ensure the safety of the system against unauthorized network access, take security measures such as
using a firewall.
Network setting
Set GX Works3 as required for the servo amplifier network settings, then configure the network. Set the master station and
servo amplifier of CC-Link IE TSN according to the following procedure.
If an alarm has occurred, refer to the following manual.
MR-J5 User's Manual (Troubleshooting)
1. Master station setting
Refer to the GX Works3 manual.
2. IP address setting
Set the IP address with the rotary switches and parameter.
MR-J5-G/MR-J5W-G User's Manual (Introduction)
MR-J5D-G User's Manual (Introduction)
Refer to the following when setting with parameters.
Page 17 IP address setting function
3. Network setting servo parameter setting
MR-J5-G/MR-J5W-G User's Manual (Parameters)
4. Network connection procedure
Page 14 Network connection procedure

14 1 CC-Link IE TSN
1.2 Startup
Settings when connecting to Mitsubishi Electric Motion Unit
To control the stroke limit on the controller side, set [Pr. PD41]. For details, refer to the manual for the controller being used.
When using an absolute position detection system, set [Pr. PA03] and [Pr. PC29]. For details, refer to the manual for the
controller being used.
If necessary, set the following servo parameters in accordance with the controller settings.
Set [Pr. NPA12] for use in 100 Mbps. By default, the communication speed in "Network automatic setting" is set to 1 Gbps.
Network connection procedure
Follow the procedures below to set up the network.
1. Connect the master station and the servo amplifier with a network cable. There is no difference between CN1A and
CN1B.
2. Turn on the power of the master station and the servo amplifier.
3. Open the diagnostic screen of GX Works3 and make sure that there is no error in the network. If the network is not
connected, check the following contents.
• Check if an alarm has occurred in the servo amplifier. If an alarm occurs, refer to the following manual and cancel the
alarm.
MR-J5 User's Manual (Troubleshooting)
• Check that the values of the rotary switches or [Pr. NPA02 IP address] match the value of IP address set in the master
station.
Network disconnection procedure
Refer to the following.
Page 11 Disconnecting the communication
Changing the network configuration
Refer to the following.
Page 11 Changing the communication configuration
Servo parameter Name
PD41.2 Limit switch enabled status selection
PD41.3 Sensor input method selection
Servo parameter Name
PA03.0 Absolute position detection system selection
PC29.5 [AL. 0E3 Absolute position counter warning] selection
Servo parameter Name
PN02 Communication error - Detection time
PN05 Communication error - Detection frequency setting
Network parameter Name
NPA12 Communication speed

1 CC-Link IE TSN
1.2 Startup 15
1
CC-Link IE TSN Class A settings
To establish communication between the master and device stations (servo amplifiers) through CC-Link IE TSN Class A,
configure the settings as follows.
Master station setting
Update the profile (CSP+) before configuring the network settings of the master station.
For CC-Link IE TSN Class A, the servo amplifier starts in the profile position mode. Set PDO mapping for profile mode
operation (pp/pv/tq/hm).
For details, refer to the manual for GX Works3.
Servo parameter setting
Set [Pr. PN03.1 CC-Link IE TSN Class setting] to "1" (Class A ver. 2.0).
Setting the servo parameter using the multi-axis project in MR Configurator2 changes the CC-Link IE TSN Class of multiple
servo amplifiers at a time.
Servo parameter Name
PN03.1 CC-Link IE TSN Class setting

16 1 CC-Link IE TSN
1.3 Application function
1.3 Application function
CC-Link IE TSN Network diagnostics
The servo amplifier supports the following CC-Link IE TSN Network diagnostic functions. Check the reference destination in
the reference column for precautions specific to the servo amplifier. Refer to the GX Works3 manual for details of other
functions.
Selected station communication status monitor
The detailed state of the currently selectable device on the network map monitor is displayed on the selected station
communication status monitor. The items displayed on the selected station communication status monitor are shown below.
In the selected station communication status monitor, CN1A is displayed as PORT2, and CN1B as PORT1.
Remote Operation
The only executable function on servo amplifiers is Reset. When Reset is executed to the servo amplifier, the servo amplifier
resets the software. For details on software reset, refer to "Software reset" in the following manual.
MR-J5 User's Manual (Function)
Function type Function Description Reference
Monitoring function of
network status
Network map monitor The current network connection configuration is displayed as a diagram.
Information such as the connection status of cables, duplication of IP address,
and the disconnection status of stations can be monitored.
The error history stored in the servo amplifier can be read and deleted. These
operations can be performed by servo amplifiers with firmware version B0 or
later.

Selected station
communication status
monitor
The details of the unit status and the communication status of the selected
station are displayed. If an error occurs in the unit, the cause of the error and its
remedies can be checked.
Page 16
Selected station
communication
status monitor
Setting change function
of network status
Reserved station
specification/
cancellation
This function designates a specified station as a reserved station, or cancels it. 
Selected Station
Operation
Remote Operation A reset command can be sent to the specified station. Page 16
Remote Operation
Setting item Description Reference
Status display The status of the servo amplifier is displayed via LED. MR-J5-G/MR-
J5W-G User's
Manual
(Introduction)
MR-J5D-G
User's Manual
(Introduction)
CC-Link IE TSN status display The CC-Link IE TSN status (CN1A/CN1B connector LED) is displayed.

1 CC-Link IE TSN
1.3 Application function 17
1
IP address setting function
IP addresses are delivered from the controller to servo amplifiers via CC-Link IE TSN.
Set the IP address required for CC-Link IE TSN communication from the following items. The IP address range is between
0.0.0.1 and 223.255.255.254. Set the IP address within the range.
The initial value of the IP address is as follows.
[Pr. NPA01 IP address
setting]
Rotary switches
(SW1/SW2)
IP address
"00000000h" (The rotary switch is
used.)
00h 1st octet Use the value of/for [Pr. NPA02 IP address].
2nd octet
3rd octet
4th octet
01h to FEh 1st octet Use the 1st to 3rd octet values of [Pr. NPA02 IP address].
2nd octet
3rd octet
4th octet The setting value of the rotary switch (SW1/SW2) is used.
FFh Not available.
"00000001h" (Network
parameters are used.)
1st octet Use the value of/for [Pr. NPA02 IP address].
2nd octet
3rd octet
4th octet
Item Initial value
IP address 192.168.3.1
Subnet mask 255.255.255.0

18 1 CC-Link IE TSN
1.3 Application function
Parameter automatic setting
The parameters of the servo amplifier are held by the master station, and are compared with those of the replaced servo
amplifier. When there is a difference in those parameters, the parameters held by the CPU module are automatically written to
the replaced servo amplifier.
Storage method of parameters
There are following two ways to store parameters in the master station.
• If data in the non-volatile memory of the servo amplifier are rewritten by the engineering tool, the parameters in the CPU
module are also updated automatically.
• If differences from the previously stored parameters are found in a periodical check, the parameters in the CPU module are
also updated automatically (Set an interval in [Pr. PN20 Parameter automatic backup update interval] for that periodical
check).
Parameters that can be stored
The parameters that can be written on the servo amplifier and stored with this function are as follows.
• Servo parameters
• Network parameters
• When the parameter that requires power cycling after being set is changed by the parameter automatic
setting, [AL. 09E.7 Parameter unreflected warning] occurs. Cycle the power of the servo amplifier.
• Do not turn off the power supply of the controller during backup. Before turning off the power supply of the
controller, check the rewrite-status of the parameter file of the device station by using the event history
function of the controller.
• Parameters that are automatically updated by the servo amplifier, such as auto tuning data, may not match
the data stored in the device station parameter file on the controller. To match the data, first read the servo
amplifier parameters using MR Configurator2 or other engineering tools, then reflect the readings on the
device station parameter file on "Detail Setting" in "Parameter Automatic Setting" of GX Works3 before
writing the readings to the controller again. Or, set [Pr. PN20 Parameter automatic backup update interval]
so that the data can be backed up in the master station periodically.
• If performing automatic backup with the interval set in [Pr. PN20], use a master station which features power
interruption protection. Failing to do so triggers [AL. 19E.1 Parameter automatic backup setting warning]. At
this time, the automatic backup is disabled.
• If the network topology is changed after the power has been turned on, the backup may not be performed.