Mitsubishi Electric DLP PH50 series User manual

DLPTM Data Display Cube
PH50 series (SXGA+ models)
XL50, XL21 series (XGA models)
Set-up and Installation Manual
March 09, 2007 (REV 2.4)

PH50, XL50, XL21 series Set-up and Installation Manual
2
Table of Contents
1. SET-UP AND INSTALLATION......................................................................................................5
1.1. Overview ...............................................................................................................................5
1.1.1. Product lineup ................................................................................................................5
1.1.2. Flowchart........................................................................................................................5
Start..................................................................................................................................................5
1.2. Cube installation....................................................................................................................6
1.2.1. Safety precaution ...........................................................................................................6
1.2.2. Preparation.....................................................................................................................6
1.2.3. Input board installation (optional)....................................................................................7
1.2.4. Unlocking (for X XL L2 21 1 ).....................................................................................................8
1.2.5. Cube stacking (for R Re ea ar r ).............................................................................................10
1.2.6. Cube stacking (for F Fr ro on nt t ) ............................................................................................13
1.2.7. Screen open/close (for F Fr ro on nt t ) .....................................................................................21
1.3. Connecting..........................................................................................................................23
1.3.1. Control signal connection .............................................................................................23
1.3.2. Image signal connection...............................................................................................23
1.3.3. Internal cabling (for F Fr ro on nt t )...........................................................................................24
1.4. Initial set up .........................................................................................................................25
1.4.1. Menu operation ............................................................................................................25
1.4.2. Dipswitch setting...........................................................................................................28
1.4.3. Picture outline adjustment............................................................................................28
1.5. System memory setting.......................................................................................................37
1.5.1. System set up...............................................................................................................37
1.5.2. Color balance adjustment.............................................................................................44
1.5.3. Image set up.................................................................................................................48
1.6. Input memory setting (for the main input).............................................................................51
1.6.1. Input port selecting.......................................................................................................51
1.6.2. Automatic input signal scanning ...................................................................................51
1.6.3. Signal adjustment.........................................................................................................52
1.6.4. Image quality adjustment..............................................................................................55
1.6.5. Input memory saving....................................................................................................56
1.6.6. Input memory calling/deleting.......................................................................................56
1.7. Input memory setting (for the input board)...........................................................................57
1.7.1. Input port selecting.......................................................................................................57
1.7.2. Expansion setting.........................................................................................................57
1.7.3. Automatic input signal scanning ...................................................................................57
1.7.4. Signal adjustment.........................................................................................................58
1.7.5. Image quality adjustment..............................................................................................63
1.7.6. Input memory saving....................................................................................................65
1.7.7. Input memory calling/deleting.......................................................................................65
1.8. Display memory setting (for the input board) .......................................................................66
1.8.1. INPUT MEMORY..........................................................................................................66
1.8.2. H.DISPLAY POS, V.DISPLAY POS..............................................................................66
1.8.3. CROP...........................................................................................................................66
1.8.4. DISPLAY......................................................................................................................67

REV 2.4
3
1.8.5. DIGITAL OUT...............................................................................................................67
1.8.6. SCREEN MODE...........................................................................................................67
1.8.7. Display memory saving ................................................................................................68
1.8.8. Display memory calling/deleting...................................................................................68
1.9. Setting as daisy chain connection (for the input board)........................................................69
2. REGULAR MAINTENANCE.......................................................................................................71
2.1. Lamp replacement...............................................................................................................71
2.1.1. Safety precautions........................................................................................................71
2.1.2. Procedure.....................................................................................................................72
2.1.3. Auto-lamp changing function (for C Ch ha an ng ge er r ).................................................................78
2.2. Condenser lens adjustment (for S Si in ng gl le e)..............................................................................81
2.3. Focus adjustment................................................................................................................82
2.4. Cleaning..............................................................................................................................83
2.4.1. Screen front surface.....................................................................................................83
2.4.2. Cabinet.........................................................................................................................83
2.4.3. Dust filter (for F Fr ro on nt t )....................................................................................................83
2.5. For delivery..........................................................................................................................85
2.5.1. 6-axis adjuster fixing.....................................................................................................85
2.5.2. Color wheel locking (for X XL L2 21 1 )....................................................................................85
2.5.3. Lamp cushion inserting (for X XL L2 21 1 C Ch ha an ng ge er r )...............................................................85
2.5.4. Screen-fixing bolt tightening (for 5 50 0” ”F Fr ro on nt t ) .................................................................86
2.5.5. Screen-holding arm locking (for 6 67 7” ”F Fr ro on nt t)...................................................................86
3. FUNCTION.................................................................................................................................87
3.1. Memories.............................................................................................................................87
3.2. Menu trees ..........................................................................................................................87
3.2.1. Input memory ...............................................................................................................87
3.2.2. Display memory............................................................................................................88
3.2.3. System memory ...........................................................................................................89
3.2.4. Memory list display.......................................................................................................90
3.3. Test pattern list ....................................................................................................................91
3.4. Control panel.......................................................................................................................91
3.5. LED display.........................................................................................................................91
3.6. Terminal functions................................................................................................................93
3.6.1. RS-232C terminal.........................................................................................................93
3.6.2. CONTROL terminal......................................................................................................93
3.7. Available input signal list......................................................................................................94
3.8. Motorized adjustment tool, S-AXL50E specification.............................................................96
3.8.1. Applicable product........................................................................................................96
3.8.2. Outline drawing ............................................................................................................96
3.8.3. Accessory.....................................................................................................................96
3.8.4. Terminals......................................................................................................................97
3.8.5. Recovery procedure from error.....................................................................................98
3.8.6. Trouble shooting...........................................................................................................98
4. ADJUSTMENT SOFTWARE, “WALLABY”...............................................................................99
4.1. General................................................................................................................................99
4.2. Installation ...........................................................................................................................99

PH50, XL50, XL21 series Set-up and Installation Manual
4
4.2.1. Software Installation .....................................................................................................99
4.2.2. Connecting...................................................................................................................99
4.2.3. Dipswitch setting...........................................................................................................99
4.2.4. Starting the application.................................................................................................99
4.3. Initial set-up.........................................................................................................................99
4.3.1. Model selecting ............................................................................................................99
4.3.2. System configuration setting.......................................................................................100
4.3.3. Panel ID defining........................................................................................................100
4.3.4. Serial port setting........................................................................................................100
4.3.5. Serial port opening .....................................................................................................101
4.3.6. Turning on ..................................................................................................................101
4.3.7. Picture mute off ..........................................................................................................101
4.3.8. Data reading...............................................................................................................101
4.4. Adjustment ........................................................................................................................101
4.4.1. Service tab (for system memory)................................................................................102
4.4.2. Input tab (for input memory) .......................................................................................106
4.4.3. Display tab (for display memory) ................................................................................109
4.4.4. Memory tab ................................................................................................................110
4.4.5. Information tab ...........................................................................................................110
4.4.6. Memory copy..............................................................................................................111
4.5. Memory backup.................................................................................................................112
4.5.1. Cube data saving........................................................................................................112
4.5.2. Data sending to cubes................................................................................................112
4.6. Main window......................................................................................................................113
4.6.1. Panel selection area...................................................................................................113
4.6.2. Serial Port ..................................................................................................................113
4.6.3. Power and Mute.........................................................................................................113
4.6.4. Information.................................................................................................................113
4.7. Menu bar...........................................................................................................................114
4.7.1. File menu ...................................................................................................................114
4.7.2. Edit menu...................................................................................................................115
4.7.3. System Config menu..................................................................................................116
4.7.4. Test Patterns menu ....................................................................................................116
4.7.5. Serial Port menu.........................................................................................................117
4.7.6. Special menu..............................................................................................................117
4.7.7. Help menu..................................................................................................................117
5. ABOUT TRADEMARKS ..........................................................................................................118
6. REVISION HISTORY................................................................................................................119

REV 2.4
5
1. Set-up and installation
1.1. Overview
1.1.1. Product lineup Screen size
Lineup Resolution Lamp Access 50” 67”
F
Fr ro on nt t – VS-67PHF50U
P
PH H5 50 0
series S
SX XG GA A+ + C Ch ha an ng ge er r R
Re ea ar rVS-50PH50U VS-67PH50U
F
Fr ro on nt tVS-50XLWF50U VS-67XLWF50U
C
Ch ha an ng ge er rR
Re ea ar rVS-50XLW50U
(VS-50XLW20U) VS-67XLW50U (VS-67XLW20U)
F
Fr ro on nt tVS-50XLF50U
(VS-50XLF20U) VS-67XLF50U
X
XL L5 50 0/
(X XL L2 21 1)(*1)
series X
XG GA A
S
Si in ng gl le eR
Re ea ar rVS-50XL50U
(VS-50XL21U, VS-50XL20U) VS-67XL50U (VS-67XL21U, VS-67XL20U)
(*1) Parenthesized products are X XL L2 21 1series.
1.1.2. Flowchart
Start
Major setting items
1.2 Cube installation
1.2.5 Cube stacking
(for R Re ea ar r ) 1.2.6 Cube stacking (for F Fr ro on nt t )
• Input board installation (optional)
• Unlocking (for X XL L2 21 1 )
1.3 Connecting
• Control signal connection
• Image signal connection
• Internal cabling (for F Fr ro on nt t )
1.4 Initial set up • Operation mode (to advanced mode)
1.4.2 Dipswitch setting
1.4.3 Picture outline adjustment
• Displaying internal test pattern
• 6-axis adjustment
• Mirror adjustment
1.5 System memory setting
1.5.1 System set up • LAMP POWER
• SYSTEM SYNC
• HOT EXCHANGE (for C Ch ha an ng ge er r)
1.5.2 Color balance adjustment • CSC
• GRADATION
• TARGET COLOR
• SENSOR
1.5.3 Image set up (When necessary)
1.6 Input memory setting
(for the main input)
1.7 Input memory setting
(for the input board)
• Input port selecting
• Automatic input signal scanning
• H.POSITION, V.POSITION
• FINE
• AMP GAIN
1.8 Display memory setting
(for the input board)
1.9 Setting as daisy chain
connection (for the input
board)
Finish

PH50, XL50, XL21 series Set-up and Installation Manual
6
1.2. Cube installation
1.2.1. Safety precaution
• This product requires a special installation to prevent falling or toppling. This should be done
by installation specialists.
• Be sure to read this manual and the user’s manual for your safety before starting assembly
or installation.
• Be sure to use supplied accessories for assembly or installation.
• Attach all the screws and fixtures specified in this manual securely.
• Reinforce the wall surface and floor so that it can support the total weights of the products
for a long time and resist earthquakes, possible vibrations, and external forces.
• Ensure that the safety factor is more than 10 (or ensure that the total bolts can bear ten
times the weight of products and the brackets).
• Do not use the product near a heater or in a humid, dusty or smoky location.
• Unless otherwise specified, do not install the product with its intakes, exhaust slots and
ventilation holes blocked. The unit may overheat and cause a fire or breakdown.
• Be sure that a lighting or sunlight does not leak into the screens.
• Inspect the mounting fixings more than once in a year as needed.
1.2.2. Preparation
• Before installation, remove the desiccant(s) taped on the top of the product.
• Make sure that all of the following are supplied.
Supplied accessories (per unit) Q’ty Necessary tools
1. Hexagon socket head bolt (M6) 8
2. Flat washer (for M6) 8
3. Spring washer (for M6) 8
4. Joint hole seal 1
5. Power cord (1.8m) for NorthAmerica and Europe
(in VS-50XL20U and VS-67XL20U) 2
6. Control cable 1
7. User’s manual 1
8. Plastic cable tie (for F Fr ro on nt t) 6 (5
50 0” ”),
10 (6 67 7” ”)
1. Allen wrench
2mm, 2.5mm, 4mm, 5mm
2. Phillips screwdriver #0, #2
3. Level
4. Stepladder
5. Spacer (for suitable screen
gaps)
6. Wrench (for base stand level
adjuster)
Optional products Others
1. Wireless/wired remote control: R-XL50TX
2. RGB input board:
VC-B50KA (for P PH H5 50 0, X XL L5 50 0), VC-B20KA (for P PH H5 50 0, X XL L2 21 1)
3. Video input board:
VC-B50KV (for P PH H5 50 0, X XL L5 50 0), VC-B20KV (for P PH H5 50 0, X XL L2 21 1)
4. Power cord (3m):
JC-PC3MA (for North America)
JC-PC3ME (for Europe)
JC-PC3MC (for China)
5. External AC fan (for 5 50 0” ”S Si in ng gl le eF Fr ro on nt t):
JC-AF115R (for AC115V)
JC-AF230R (for AC230V)
6. Motorized adjustment tool: S-AXL50E
7. Spare lamp:
S-PH50LA (for C Ch ha an ng ge er r)
S-XL50LA (for S Si in ng gl le e)
8. Spare color wheel:
S-PH50CW (for P PH H5 50 0)
S-XL50CW (for X XL L5 50 0), S-XL20CW (for X XL L2 21 1)
1. Base stand
2. Base stand level adjuster
3. Base stand level adjuster
fixing metal part
4. Wall fixing metal part
5. Anchor bolt
6. Hexagon socket head cap
screw (M6)

REV 2.4
7
1.2.3. Input board installation (optional)
When using the optional input board, install it into the product according to the following steps.
In F Fr ro on nt t, a slot for the board is located inside the cube. Open the screen unit before installation
according to the chapter 1.2.7 on page 21.
When you attach it, be sure to turn off the main power switch.
1. Remove a panel cover on the control panel by removing 6
screws at the positions shown in the figure.
2. When you use the video input board, attach
it as right figure. Stick a supplied terminal
name label on the RGB input board, and
combine the boards with supplied 2 screws.
3. Firmly insert the input board into the board
slot along guide rails till the end.
4. Firmly fix the input board with the 6 screws that have been
removed in the step 1.
In
p
ut boa
r
d
Panel cover
2. Stick the supplied
terminal name label,
and then combine
the boards with 2
supplied screws.
Video input board
RGB input board
1. Remove 2 hole-stoppers.
Insert

PH50, XL50, XL21 series Set-up and Installation Manual
8
1.2.4. Unlocking (for
X
XL L2 21 1 )
Surely release following locks before turning on the main power switch. Turning on without
releasing may cause damage.
1.2.4.1. Color wheel unlocking
The color wheel is located on the optical unit inside the cube. In F Fr ro on nt t, open the screen unit
according to the chapter 1.2.7 on page 21 before unlocking. Turning on without unlocking may
cause damage.
1. Make sure a key slot on the
color wheel cushion faces
the top as you begin the
procedure.
2. Pull the color wheel cushion till the flange hits
the metal part.
• For C Ch ha an ng ge er r, pliers are recommended to
use since it is hard to access with fingers.
3. Turn it 90 degrees clockwise.
Caution
Before shipment, be sure to lock the color
wheel in the reverse order of unlocking
(chapter 2.5.2, on page 85). Shipping the
product without locking may cause
breakage.
Stopper
Flange Metal
Metal
Key slot
Color wheel cushion

REV 2.4
9
1.2.4.2. Lamp cushion removing (for C Ch ha an ng ge er r)
Remove a lamp cushion before turning on the main power switch. Turning on without removing
may cause smoking and catching fire.
• It should be remembered to lock the lamp cover after removing. If you neglect to lock it, the
lamp changer may not work correctly.
Caution
Before shipment, be sure to insert the
cushion in the reverse order of removing
(chapter 2.5.3, on page 85). Shipping the
product without inserting may cause
breakage.
Lamp cushion
Lam
p
cove
r
Lock

PH50, XL50, XL21 series Set-up and Installation Manual
10
1.2.5. Cube stacking (for R Re ea ar r )
1.2.5.1. Assembling the base stands and cubes
1. Assemble base stands.
2. Adjust level adjusters to make the base stand both level
and plumb by means of a spirit level.
3. Loosen 4 screen-fixing screws per unit shown
with arrow lines in the right figure with an Allen
wrench (5 mm) to remove the screen units
from all cubes to be installed. (This applies to
5
50 0” ”, which is supplied with the screen fitted).
4. 6 67 7” ”P PH H5 50 0: Turn a center screw in the lower
door 90 degrees anti-clockwise to unlock with
an Allen wrench (4mm).
5. Open the lower door 90 degrees by pushing
down the handles. And then slide it to right to
detach. The door cannot be detached other
than 90 degrees opening position.
6. Place a cube on the base stand.
7. Fix the cube at 4 points with supplied hexagon
socket head bolts, spring washers and flat
washers.
Caution
When holding up a cube, be careful not
to put your hand between the cube and
the base stand.
Lower door
Hexagon socket
head bolt
Base stands
Level adjusters
Screen unit
Cube unit
Flat washer
Spring washer
Screen-fixing
screws
Center screw
(6 67 7” ”P PH H5 50 0)

REV 2.4
11
8. Place the next bottom row cube on the base stand
and fix it in the same way.
9. Join right and left cubes at 4 points with supplied
hexagon socket head bolts, spring washers and flat
washers.
10. Place cubes for the upper row on the
assembled units.
11. Fix them vertically and horizontally at 4 points
each with supplied hexagon socket head bolts,
spring washers and flat washers.
12. Stop up the holes on both sides with supplied
joint hole seals, which holes are not used for a
display wall.
Caution
To avoid units from falling, measure
horizontal and vertical degrees with a
level etc. to make sure the units are
stably assembled.
1.2.5.2. Screen gap adjustment
1. Temporarily attach the screen units, which
were detached in the previous step. (For
67-inch models, the screens were supplied
separately).
2. Put spacers between screens and adjust the
screen gaps to be:
1 mm for 5 50 0” ”or
2 mm for 6 67 7” ”.
3. Tighten the 4 screen-fixing screws. Be
careful not to tighten with an excessive
torque (suggested torque: 3.9Nm).
1mm
(2mm)
1mm
(2mm)
Joint hole seals

PH50, XL50, XL21 series Set-up and Installation Manual
12
1.2.5.3. Fixing to the wall and floor
You don’t have to attach the lower door in this chapter since picture outlines have yet to be
adjusted as explained in the next chapter.
After the picture outline adjustment, attach the door in the reverse order of detaching.
1. Attach floor-fixing brackets on 4 level adjusters below the base stand and fix them to the
floor with anchor bolts.
2. Fix the upper back part of the display wall to the back wall with wall-fixing brackets as shown
in the following figure.
Caution
Make sure the whole set is assembled firmly and installed stably. To prevent the set
from falling due to unpredictable events such as earthquakes and shocks, fix the set
firmly to the wall and floor. Furthermore, carefully confirm the strength of the fixing area
of the installation place (wall and floor). The wall and floor fixing method differs
according to the number of assembled units.
A
nchor bolts
Adjusters
A
nchor bolts
Wall-fixing brackets
Floor-fixing brackets
Hexagon socket head
cap screws (M6)

REV 2.4
13
1.2.6. Cube stacking (for F Fr ro on nt t )
Caution
Take heed of appropriate surrounding space for ventilation (except rear surface) such
as not to pool the hot air on the top of the display walls so that the ambient
temperature doesn’t exceed the product environmental requirements.
1.2.6.1. Tape peeling off (for 6 67 7” ”)
The screen-holding arms in both sides are taped at each end for transportation. Peel them off
before installation.
Tape
Tape
Screen-
holding arm

PH50, XL50, XL21 series Set-up and Installation Manual
14
1.2.6.2. Screen detaching
For 5 50 0” ”which is supplied with the screen fitted, the screen unit should be detached before
installation. (For 6 67 7” ”, the screens are provided separately.)
6
67 7” ”: Screen attaching/detaching work should be done by two or more people.
Be careful not to trap your fingers when you slide its arms during detaching/attaching work.
1. 5 50 0” ”: Remove two screen-fixing bolts (M6 – 45mm,
gold hexagon socket).
Caution
Before shipment, be sure to tighten the bolts (see
chapter 2.5.4, on page 86). Shipping the product
without tightening may cause breakage.
2. Pull screen-drawing handles in both sides to draw the screen
till locked.
3. Lift up and detach the screen unit with pushing
screen-detaching levers located inside the screen unit in
both sides. Be careful not to
push the adjacent flip-up lock
lever.
4. Press down the slide lock levers in both sides to unlock, and
put back the screen-holding arms.
6
67 7” ”: The levers can be
unlocked respectively.
Screen-fixing
bolts
Screen-drawing handle
Screen-detaching lever (inside the screen unit)
Screen-holding arm
(Flip-up lock lever)
Slide lock lever (Inside the arm)
Push

REV 2.4
15
1.2.6.3. Ventilation
To ensure a proper airflow for cooling, you need to block some vents as the following figures.
1.2.6.3.1. For
6
67 7” ”, 5 50 0” ”C Ch ha an ng ge er r
1. Block the vents in the bottom row. Prepare a cover material by yourself in reference to the
figures below. The covers can be fixed with two self-tapping screws (nominal diameter: 4mm,
length: 8 – 12mm) on the holes of the corner joint. Be sure this work is only for the cubes in
the bottom row.
Vent covers (example):
Material: aluminum or steel plate (thickness: 1mm)
2. To keep dust out, seal the cable holes on the top of the display wall. Prepare a cover
material by yourself. The size of the holes is 116.5mm x 63mm. Be sure this work is only for
the cubes in the top row.
Panel 1 Panel 2
Panel 3 Panel 4
Exhaust
Exhaust
Intake
Vents to be blocked
Top row
Bottom row
Base stand
Intake
External AC fans (occasional)
Should be blocked
A
irflow concept
Panel 1
(From rear)
Panel 2
(From rear)
Panel 3
(From rear)
Panel 4
(From rear)
Exhaust
Vents to be blocked
Exhaust
For 6 67 7” ”, 5 50 0” ”C Ch ha an ng ge er rFor 5
50 0” ”S Si in ng gl le e
Vent cove
r
Two self-tapping screws
(nominal diameter: 4mm,
length: 8 – 12mm)
Holes of corner joint
Cable
hole
For 6 67 7” ”
For 5 50 0” ”C Ch ha an ng ge er rUnit [mm]
Intake
(from right side
in5 50 0” ”C Ch ha an ng ge er r)
Exhaust

PH50, XL50, XL21 series Set-up and Installation Manual
16
X
XL L5 50 0
X
XL L2 21 1
1.2.6.3.2. For
5
50 0” ”S Si in ng gl le e
According to circumstances, attach the optional external AC fans (JC-AF115R or JC-AF230R) on
the intake vents in the bottom row (see “External AC fan attaching” on page 17).
• Prepare openings on base stands to ventilate.
• Keep enough base stand height not to inhale a coat of dust on a floor from the intake vents.
1. To block the bottom row, detach the bottom duct cover from inside the cube and attach it on
the bottom of the duct. Be sure this work is only for the cubes in the bottom row.
2. To block the top row, remove the cushion unit on the top at first. Then detach the top duct
cover from the top surface of the cube and attach it on the top of the duct. Be sure this work
is only for the cubes in the top row.
3. To keep dust out, seal the cable holes on the top of the display
wall. Prepare a cover material by yourself. The size of the
holes is 116.5mm x 63mm. Be sure this work is only for the
cubes in the top row.
Detaching
Tighten the duct screw
to attach with duct
panel.
Cable hole
Detaching
Top duct cover
Cushion unit Bottom duct cover
Tighten removed screw
to attach.
Detaching
Tighten removed 3
screws to attach.

REV 2.4
17
External AC fan attaching (occasional)
When 4-high configuration with 5 50 0” ”S Si in ng gl le e, attach the optional external AC fans (JC-AF115R or
JC-AF230R) on intake vents. Even in 3-high configuration, attach the AC fans as well, when
spaces are narrower than 50cm to the ceiling and 10cm to the wall behind. Narrow spaces tend
to rise the cube internal heat. Be sure this work is only for the cubes in the bottom row.
1. Attach a suitable plug to the bare end of the power
cord of the fan to correspond with an interface such
as a terminal block or a power strip. 2-meter AC
power cord is included in the fan.
2. Insert the fan into the intake vent till click.
3. Fix it to the lower part of cube with the screw supplied
with the fan.
Note:
• To avoid injuries and shock hazards, do not carry
electricity to the fan during this work. It must be done
by qualified personnel.
• Be sure to use the fan within the range of its power
rating.
• The outline of the fan is shown below. Prepare a base stand which does not interfere with the
fan.
Front view Side view
External
A
C fan
Lower part of cube
[Unit: mm]
Intake vent
External
A
C fan

PH50, XL50, XL21 series Set-up and Installation Manual
18
1.2.6.4. Assembling base stands and cubes
1. Assemble base stands.
2. Adjust level adjusters to make the base stand both level and
plumb by means of a spirit level.
3. Place a cube on the base stand.
Caution
Do not grip the screen-holding arms to
lift up a cube cabinet. It may cause
breakage.
4. Fix the cube at 4 points with supplied hexagon
socket head bolts, spring washers and flat
washers.
Caution
When holding up a cube, be careful not
to put your hand between the cube and
the base stand.
5. Place the next bottom row cube on the base stand and fix it in
the same way.
6. Join right and left cubes at 4 points with supplied hexagon
socket head bolts, spring washers and flat washers.
7. Place cubes for the upper row on the assembled units.
8. Fix them vertically and horizontally at 4 points each with
supplied hexagon socket head bolts, spring washers and
flat washers.
9. Stop up the holes on both sides with supplied joint hole
seals, which holes are not used for a display wall.
10. Run cables through the internal cabinets according to the
chapter 1.3.3 on page 24 before attaching the screen unit.
Caution
To avoid units from falling, measure horizontal and
vertical degrees with a level etc. to make sure the units
are stably assembled.
Base stands
Level adjusters
Hexagon socket
head bolt
Spring washe
r
Flat washe
r
Joint hole seals

REV 2.4
19
11. Press down the slide lock levers in both sides to unlock, and
draw the screen-holding arms till locked.
6
67 7” ”: The levers can be unlocked respectively.
12. Reinstall the screen unit in its original
cabinet. Put the pins inside the screen
unit on the retainers at the top of the
screen-holding arms, following which
make the screen upright. Make sure it
will be locked securely.
6
67 7” ”: Screen attaching/detaching work
should be done by two or more
people.
13. Press down the slide lock
levers in both sides to unlock,
and push the screen unit along
the rail till the end.
6
67 7” ”: The levers can be
unlocked respectively.
5
50 0” ”: You don’t have to tighten
the removed two screen-fixing
bolts.
1.2.6.5. Screen gap adjustment
This adjustment is normally unnecessary.
As needed, you can adjust the screen gaps.
1. Estimate a distance to move the screens so that
the screen gaps will approximately be:
2 mm for 5 50 0” ”or
3 mm for 6 67 7” ”.
2. Open the screen units (chapter 1.2.7.1, on page
21).
Screen-holding arm
Slide lock lever (Inside the arm)
Slide lock lever (Inside the arm)
2mm
(3mm)
2mm
(3mm)
screen-holding arm
Pin
Retainer

PH50, XL50, XL21 series Set-up and Installation Manual
20
A
nchor bolts
3. For horizontal adjustment:
5
50 0” ”: Loosen two screws in the right screen guide to adjust its
horizontal position and fix them. 6 67 7” ”: Loosen the screw in the bottom screen guide to adjust
its horizontal position and fix it. The screen guide has punch marks at the adjustable range
(+/- 2mm) and its center.
4. For vertical adjustment: Loosen two screws each in the left and right screen guides to adjust
their vertical positions and fix them. 6 67 7” ”: The screen guides have the punch marks at the
same position as described above.
5. Close the screen units (chapter 1.2.7.2, on page 22).
6. Check the screen gaps and repeat the steps until you get reasonable gaps.
1.2.6.6. Fixing to the wall and floor
1. Attach floor-fixing brackets on 4 level adjusters below the base stand and fix them to the
floor with anchor bolts.
2. Fix the upper back part of the display wall to the back wall with wall-fixing brackets as shown
in the following figure.
Caution
Make sure the whole set is assembled firmly and installed stably. To prevent the set from falling
due to unpredictable events such as earthquakes and shocks, fix the set firmly to the wall and
floor. Furthermore, carefully confirm the strength of the fixing area of the installation place (wall
and floor). The wall and floor fixing method differs according to the number of the assembled units.
A
djusters
A
nchor bolts
Wall-fixing brackets
Floor-fixing brackets
Hexagon socket head
cap screws (M6)
5
50 0” ”Left screen guide
For horizontal
adjustment
For vertical
adjustment
For vertical
adjustment
6
67 7” ”Bottom screen guide 6
67 7” ”Screen guide (both side)
5
50 0” ”Right screen guide
For vertical
adjustment
For horizontal
adjustment