Mitsubishi DX-TL800E120 User manual

1
ENGLISH
OTHERS
DIGITAL RECORDER
RS232 PROTOCOL
MODEL
DX-TL800E120
THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER.

60
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Connecting to a personal computer
■ Connecting with a personal computer
This unit can be remote controlled from a PC equipped with a RS-232C connection. It is also possible to input comments
from a PC for recording comment information along with the video.
♦Connection via modem
PleaseuseRS-232CStraight cable(9pin) toconnect amodem withthis unit.Thesettingof CTSshould beset to“HIGH”
or “ON”. Please refer to the instruction manual of a modem for details about connection.
Unit
Modem Modem
Telephone line Personal Computer
RS-232C straight cable (9 pin)
Y/C
1
MAIN
OFF
ON
AC IN ~
234 56789
14
RESET
RS-232C
23 56789
1
ALARM IN
2 3 4 5 6 7 8 9
CLOCK ADJ REC EMERGENCY RESERVED MODE OUT 1 MODE OUT 2 MODE OUT 3 MODE OUT 4 CALL OUT CALL OUT GND MAX 30mA DC 5V OUT GND
CAMERA OUT
RS-232C
RESET
CAMERA IN
INOUT
VIDEO OUT
MIC
GND
AUDIO
100V
♦Direct connection
Please use RS-232C Crossover cable (9pin) to connect a modem with a personal computer. RS -232C Crossover cable
differs depending on the personal computer.
Y/C
1
MAIN
OFF
ON
AC IN~
234 56789
14
RESET
RS-232C
23 56789
1
ALARM IN
2 3 4 5 6 7 8 9
CLOCK ADJ REC EMERGENCY RESERVED MODE OUT 1 MODE OUT 2 MODE OUT 3 MODE OUT 4 CALL OUT CALL OUT GND MAX 30mA DC 5V OUT GND
CAMERA OUT
RS-232C
RESET
CAMERA IN
INOUT
VIDEO OUT
MIC
GND
AUDIO
100V
Unit
Personal Computer
RS-232C Crossover cable (9 pin)
♦RS-232C Terminal
RS-232C
1
69
5
RXD
TXD
DTR
GND
Receiving Data
Transmission Data
Data Terminal Ready
Signal Ground
Pin NO.
Letters Letters
Pin NO.
Transmission Contents Transmission Contents
DSR
RTS
CTS
Data Set Ready
Request To Send
Clear To Send
2
3
4
5
6
7
8
♦RS-232C Cable
Please use the following RS-232C Crossover cable to connect your personal computer to the unit.
FRAME
D-sub 9 pin (unit) D-sub 25 pin (Personal computer)
FG
TXD
RXD
RTS
CTS
DSR
GND
DTR
1
2
3
4
5
6
7
20
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
1) When RS-232C terminal of personal
computer is D-sub 25 pin
D-sub 9 pin D-sub 9 pin
FRAMEFRAME RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
2) When Personal computers RS-232C
terminal is D-sub 9 pin

61
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
Command codes
■ RS-232C settings
Communication related settings of this unit are made in “MODE”and “SETTINGS”of the <RS-232C> screen. Perform
settings so that they are the same as the connecting modem or PC.
When remote controlling this unit from a PC, set “MODE”in the <RS-232C> screen to “REMOTE A”(status
condition change information is returned from the unit) or “REMOTE B”(status condition change information is not
returned from the unit).
1
2
3
4
5
TRANSMISSION
RATE
DATA BIT LENGTH
PARITY BIT
STOP BIT
DELIMITER
1200/2400/4800/
9600/19200
8 BIT/7 BIT
NONE/ODD/EVEN
1 BIT/2 BIT
CR/CR•LF
Synchronization Name on Menu Asynchronous
1
2
3
X control
S parameter
CS-RS hand-shake
Not available
Not available
Available
Synchronization Name on Menu
Pe rform the fo llowing settings on the PC
Transmission rate at
the data received/
sent
Data bit length
Parity bit setting
Stop bit length
Line feed setting
Ava ilable setting s on unit
■ Command code system
2 types of command codes of “direct operation specification”and “false operation panel”can be selected according to
the purpose of the unit.
■ Description of command code systems
♦Direct operation specification
Control and settings are performed by checking execution, errors, etc., from the status returned from the unit for the
command sent from the PC. This command type is structured by operation setting type commands that sets operations
and menu setting type commands that directly sets various menus.
• Input format
Operation setting type commands are to be sent from the PC for each operation such as power on/off, record, playback,
etc., for the unit.
Menu setting type commands are to be specified for each menu setting of the unit.
As a general rule, do not send commands continuously, but send the next command after checking that the present
command has been executed and completed.
• Response format
After sending a command, the following items can be checked from the status returned from the unit.
1) Command execution result, error type, command name, operation status.
2) For operation setting type commands, the operation mode of the unit can be distinguished by the mode number of the
returned status.
Distinction cannot be made with menu setting type commands. (Mode number is notified only when there is change is
status.)
Indicates POWER ON command has been sent.
Indicates that the unit has received a command.
EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful.
PW1 : Indicates response to POWER ON command.
03 : Indicates POWER ON status.
Example) Turn the Unit ON.
Command
from PC Replied status code
from unit to PC Meaning
PW1 RC
EX,00PW1,03 #2
#2
#1
When the unit cannot execute the operation setting type command or menu setting command sent from a PC,
the content is displayed in the error type of the status returned from the unit. Check the error code and take
appropriate measures.
For control type commands such as record, playback, etc., the interval between command transmission and
the actual operation (command execution) may take some time. To prevent the gap between operation and actual
execution, read the status after sending the command and check the transition of the actual execution.

62
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
♦False operation panel command type
Operations can be specified from a PC as if operating the actual operation panel of the unit while viewing the output
video. Each command is a command type that corresponds to the operation button of the unit.
• Input confirmation type
Send commands as if operate the buttons, JOG dial and SHUTTLE ring of the operation panel.As a general rule, do not
send commands continuously, but send the next command after checking that the present command has been executed
andcompleted.Aftersendingacommand, the commandexecution result, error typeand command namecan be checked
by the status returned from the unit. To check the actual execution, view the output screen of the unit on the monitor
screen.
Indicates that a command equivalent to “push the POWER button”was sent.
Indicates that the unit has received a command.
EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful.
KKP0 : Indicates that the POWER button was operated.
Indicates that a command equivalent to “push the PLAY button”was sent.
Indicates that the unit has received a command.
EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful.
KKB1 : Indicates that the PLAY button was operated.
Indicates that a command equivalent to “push the PAUSE button”was sent.
Indicates that the unit has received a command.
EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful.
KKB4 : Indicates that the PAUSE button was operated.
Command
from PC Replied status code
from unit to PC Meaning
KKP0
KKB1
KKB4
RC
EX,00KKP0
PC
EX,00KKB1
PC
EX,00KKB4
Example) Recorded data is played back using still-frames.
#2
#2
#1
#2
#2
#1
#2
#2
#1
When using shuttle operation commands, be sure to send the shuttle center command after sending the
operation command. Otherwise, the shuttle operation will be kept until the shuttle center command is sent.
For control type commands such as record, playback, etc., the interval between command transmission and
the actual operation (command execution) may take some time.To prevent the gap between operation and actual
execution, read the status after sending the command and check the transition of the actual execution.
♦Status condition change information function
EX : Indicates that a command has been executed.
AA : Indicates that status condition change information.
0103 : Indicates that status condition of POWER ON.
Example) Status condition change information of system mode and POWER ON is issued.
Replied status code
from unit to PC Meaning
EX,AA,0103 #2
When setting “MODE”( see page 41) to “REMOTE A”, a status condition change information is sent to the
PC when there is change in the unit status. The notification is not sent when setting to “REMOTE B”.
♦Command receive confirmation function
After executing a received command, the error type during command execution is notified after execution status “EX”.
Error type
Contents of Error
00
01
02
03
04
05
06
Normal
Execute Error
Execute Unable Error
Incorrect command
Incorrect parameter
Excuting the command
Not corresponding

63
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
♦Details of the numbers
#1
: When the setting of DELIMITER on <RS-232C SETTINGS> display is set to CR, carriage return code (0DH) will be
input. If the setting is CR•LF, carriage return code (0DH) and line feed code (0AH) will be input.
#2
: When the setting of DELIMITER on <RS-232C SETTINGS> display is set to CR, carriage return code (0DH) will be
output. If the setting is CR•LF, carriage return code (0DH) and line feed code (0AH) will be output.
*: Indicates one number or a character.
See “Comment search command code”, page 80.
♦Command code
• RS-232C [Direct operation specification] operation setting system command form
Commands name Commands NotesStatus
PW*
(1)
PC*
(1)
PB**
(1)
PB**
(1)
*****
(4)
Power
Recording
Playback
Alarm List search
RC
EX,**
(2)
PW*
(1)
,**
(3)
RC
EX,**
(2)
PC*
(1)
,**
(3)
RC
EX,**
(2)
PB*
(1)
,**
(3)
RC
EX,**
(2)
PB**
(1)
*****
(4)
,
**
(3)
*
(1)
: Power ON/OFF
0 : OFF 1 : ON
**
(2)
: Error type
**
(3)
: System mode number
00 : Power off 03 : Power on
06 : Setting menu 07 : Copy menu
08 : Search menu 09 : Device unusual situation
0A : Device initialize 0B : Device reconstruction
0F : System unusual situation
*
(1)
: Recording/Stop recording
0 : Stop recording 1 : Recording
**
(2)
: Error type
**
(3)
: Recording mode number
00 : Stop 03 : Stop(pause)
04 : Recording 05 : Pre alarm recording
06 : Alarm recording during pause
07 : Alarm recording during recording
08 : Alarm recording during Pre alarm recording
0A : Recording error
**
(1)
: Playback command
00 : Stop 11 : Playback
12 : Foward speed search 1 13 : Foward speed search 2
14 : Foward speed search 3 15 : Foward speed search 4
16 : Fast foward 17 : Foward field advance
21 : Reverse playback 22 : Reverse speed search 1
23 : Reverse speed search 2 24 : Reverse speed search 3
25 : Reverse speed search 4 26 : Rewind
27 : Reverse field advance 30 : Pause
41 : Forward time date search
42 : Forward record index search
43 : Forward alarm index search
44 : Forward skip search
52 : Reverse record index search
53 : Reverse alarm index search
54 : Reverse skip search
70 : Jump to start point
71 : Jump to end point
**
(2)
: Error type
**
(3)
: Playback mode number
00 : Stop 03 : Playback (single screen)
04 : Reverse playback (single screen)
05 : Playback pause (single screen)
06 : Reverse playback pause (single screen)
07 : Forward speed search (single screen)
08 : Reverse speed search (single screen)
09 : Fast forward (single screen)
0A : Rewind (single screen)
0B : Playback (split display)
0C : Reverse playback (split display)
0D : Playback pause (split display)
0E : Reverse playback pause (split display)
0F : Forward speed search (split display)
10 : Reverse speed search (split display)
11 : Fast forward (split display)
12 : Rewind (split display)
13 : Playback (zoom)
14 : Reverse playback (zoom)
15 : Playback pause (zoom)
16 : Reverse playback pause (zoom)
17 : Forward speed search (zoom)
18 : Reverse speed search (zoom)
19 : Fast forward (zoom)
1A : Rewind (zoom)
1C : Playback error
**
(1)
: 60
**
(2)
: Error type
**
(3)
: Playback mode number (refer to Playback mode)
*****
(4)
: Alarm list number (00000 ~ 09999)
(Latest is 00000)
#1
#1
#1
#1
#2
#2
#2
#2
#2
#2
#2
#2

64
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] operation setting system command form (Continued)
PB
**
(1)
**
(2)
**
(3)
**
(4)
**
(5)
*************
****************
***
(6)
SW
****
(1)
TM
*
(1)
AD
*
(1)
CP
*
(1)
RP
*
(1)
IF
**
(1)
WC
*
(1)
MC
*
(1)
CL
**
(1)
Comment search
Switcher
Timer
Alarm interrupt
Copy
Restore
Acquire the recorded
period
Warning reset
Menu initializing,
loading or saving
Delete the data
RC
EX,
**
(7)
PB
**
(1)
**
(2)
**
(3)
**
(4)
**
(5)
**************
*****************
*
(6)
,
**
(8)
RC
EX,
**
(2)
SW
****
(1)
,
**
(3)
RC
EX,
**
(2)
TM
*
(1)
,
**
(3)
RC
EX,
**
(2)
AD
*
(1)
,
**
(3)
RC
EX,
**
(2)
CP
*
(1)
,
**
(3)
RC
EX,
**
(2)
RP
*
(1)
,
**
(3)
RC
EX,
**
(2)
IF
**
(1)
,
**
(3)
,
**
(4)
**
(5)
**
(6)
**
(7)
**
(8)
**
(9)
**
(10)
**
(11)
**
(12)
,
**
(13)
**
(14)
**
(15)
*****
(16)
RC
EX,
**
(2)
WC
*
(1)
,
**
(3)
RC
EX,
**
(2)
MC
*
(1)
,
**
(3)
RC
EX,
**
(2)
CL
**
(1)
,
**
(3)
**
(1)
: Comment search (80)
**
(2)
: Search direction
00 : Forward 01 : Reverse
**
(3)
: number of search time (01 ~ 99)
**
(4)
: Camera number
00 : CH1 01 : CH2 02 :CH3 03 : CH4 04 : CH5
05 : CH6 06 : CH7 07 : CH8 08 : CH9
**
(5)
: Character size (00 - 32)
*****************************
***
(6)
: Comment
**
(7)
: Error type
**
(8)
: Playback mode number (refer to Playback mode)
****
(1)
: Switcher command
0101 : CH1 0102 : CH2 0103 : CH3 0104 : CH4
0105 : CH5 0106 : CH6 0107 : CH7 0108 : CH8
0109 : CH9
0180 : zoom cancel 0181 : zoom
0182 : twice zoom 0184 : four times zoom
0191 : zoom move above 0192 : zoom move down
0193 : zoom move right 0194 : zoom move left
0400 : split 4 screen sequential 0401 : 4(a)
0402 : 4(b) 0403 : 4(c)
0901 : 9a
**
(2)
: Error type
<Case of during playback>
**
(3)
: Playback mode number during playback, display mode
number during another condition.
Playback mode number : refer to playback mode
<Case of another condition>
**
(3)
: Display mode number
03 : single screen 04 : split display
05 : zoom 07 : display error
*
(1)
:Timer recording ON/OFF
0 :Timer off 1 :Timer on
**
(2)
: Error type
**
(3)
:Timer mode number
00 :Timer off 01 :Timer on
02 :Timer error
*
(1)
: Alarm interrupt setting
0 : Alarm interrupt off 1 : Alarm interrupt on
**
(2)
: Error type
**
(3)
: Alarm disable mode number
00 : Alarm disable off 01 : Alarm disable on
*
(1)
: Copy STOP/START
0 : STOP 1 : START
**
(2)
: Error type
**
(3)
: Copy mode number
00 : Stop 02 : Execute
04 : Copy error
*
(1)
: Restore STOP/START
0 : STOP 1 : START
**
(2)
: Error type
**
(3)
: Restore mode number
00 : Stop 02 : Execute
04 : Restore error
**
(1)
: Acquire the recorded period
0 : Main 1 : Copy
**
(2)
: Error type
**
(3)
: Acquire the information mode number
00 : Done 02 : Acquire information error
**
(4)
: Start year
**
(5)
: Start month
**
(6)
: Start day
**
(7)
: Start hour
**
(8)
: Start minute
**
(9)
: Start second
**
(10)
: End year
**
(11)
: End month
**
(12)
: End day
**
(13)
: End hour
**
(14)
: End minute
**
(15)
: End second
*****
(16)
: Number of alarm list
*
(1)
: Warning reset
0 : Reset (only display)
**
(2)
: Error type
**
(3)
: System mode number
(refer to Power ON/OFF command)
*
(1)
: Menu initializing, loading or saving
0 : Initialize 1 : Load 2 : Save
**
(2)
: Error type
**
(3)
: System mode number
(refer to Power ON/OFF command)
**
(1)
: Delete the data
01 : Main 03 : Copy
**
(2)
: Error type
**
(3)
: Data delete mode number
00 : Done 02 : Data delete error
Commands name Commands NotesStatus
#1
#1
#1
#1
#1
#1
#1
#1
#1
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#1
#2
#2

65
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [Direct operation specification] menu setting system command form
<TIME DATE/DISPLAY SETTINGS>
<Menu setting>
DW,
*****
(1)
*****
(2)
<Inquiry for setting information>
DR,
*****
(1)
<Menu setting>
DW02,
*****
(1)
*****
(2)
<Inquiry for setting information>
DR02,
*****
(1)
<Menu setting>
DW,
*****
(1)
*****
(2)
<Inquiry for setting information>
DR,
*****
(1)
TIME DATE ADJUST
DISPLAY MODE
CLOCK LOCATION
SETTING
CAMERA DISPLAY
CAMERA TITLE/
MEMO SETTING
DUPLEX MODE
DISPLAY
DAYLIGHT SAVING
<Writing of menu information>
RC EX,
**
(3)
DW,
*****
(1)
*****
(2)
<Reading of menu information>
RC EX,
**
(3)
DR,
*****
(1)
*****
(2)
<Writing of menu information>
RC EX,
**
(3)
DW02,
*****
(1)
*****
(2)
<Reading of menu information>
RC EX,
**
(3)
DR02,
*****
(1)
*****
(2)
<Writing of menu information>
RC EX,
**
(3)
DW,
*****
(1)
*****
(2)
<Reading of menu information>
RC EX,
**
(3)
DR,
*****
(1)
*****
(2)
*****
(1)
:
00048 :Time (Year) 00049 :Time (Month)
00050 :Time (Day) 00053 :Time (Hour)
00054 :Time (Minute) 00055 :Time (Second)
*****
(2)
:
00001 ~ 00099 :Time (Year) 00001 ~ 00012 :Time (Month)
00001 ~ 00031 :Time (Day) 00001 ~ 00023 :Time (Hour)
00000 ~ 00059 :Time (Minute) 00000 ~ 00059 :Time (Second)
**
(3)
: Error type
*****
(1)
: 00033
*****
(2)
: 00001 ~ 00006
**
(3)
: Error type
*****
(1)
: 00034
*****
(2)
: 00000 ~ 00383
**
(3)
: Error type
*****
(1)
: 00035
*****
(2)
: 00000 ~ 00003
00000 : NONE 00001 : NUMBER
00002 :TITLE 00003 : COMMENT
**
(3)
: Error type
*****
(1)
:
CH1 : 00080 ~ 00095 CH2 : 00096 ~ 00111
CH3 : 00112 ~ 00127 CH4 : 00128 ~ 00143
CH5 : 00144 ~ 00159 CH6 : 00160 ~ 00175
CH7 : 00176 ~ 00191 CH8 : 00192 ~ 00207
CH9 : 00208 ~ 00223 Memo : 05329 ~ 05344
*****
(2)
:
(Refer to CHARACTER CODE LIST)
**
(3)
: Error type
*****
(1)
: 05282
*****
(2)
:
00000 : NONE 00001 :TOP
00002 : BOTTOM
**
(3)
: Error type
*****
(1)
: 00052
*****
(2)
:
00000 : OUT 00001 : IN
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#1
#1
#1
#1

66
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] menu setting system command form
<MPX DISPLAY SETTINGS>
<Menu setting>
DW,
*****
(1)
*****
(2)
<Inquiry for setting information>
DR,
*****
(1)
SPIT 4 SCREEN
SETTING
SPLIT 9 SCREEN
SETTING
SEQUENCE SETTING
SEQ. - CH.
SEQUENCE SETTING
SPLIT 4 SETTING
SEQUENCE SETTING
TIME SETTING
INTERLASE
COVERT CAMERA
SETTING
ALARM DISPLAY
<Writing of menu information>
RC EX,
**
(3)DW,
*****
(1)
*****
(2)
<Reading of menu information>
RC EX,
**
(3)DR,
*****
(1)
*****
(2)
SPLIT 4(a)
*****
(1) : 00368 ~ 00371
00368 :Top - left 00369 :Top - right
00370 : Bottom - left 00371 :Bottom - right
SPLIT 4(b)
*****
(1) : 00384 ~ 00387
00384 :Top - left 00385 :Top - right
00386 : Bottom - left 00387 :Bottom - right
SPLIT 4(c)
*****
(1) : 00400 ~ 00403
00400 :Top - left 00401 :Top - right
00402 : Bottom - left 00403 :Bottom - right
*****
(2) : 00000 ~ 00008
00000 : CH1 00001 : CH2
00002 : CH3 00004 : CH4
00005 : CH5 00005 : CH6
00006 : CH7 00007 : CH8
00008 : CH9
**
(3) : Error type
SPLIT 9
*****
(1) : 00432 ~ 00440
00432 :Top - left 00433 :Top - middle
00434 :Top - right 00435 : Middle - left
00436 : Middle - middle 00437 : Middle - right
00438 : Bottom - left 00439 :Bottom - middle
00440 : Bottom - right
*****
(2) : 00000 ~ 00008
00000 : CH1 00001 : CH2
00002 : CH3 00004 : CH4
00005 : CH5 00005 : CH6
00006 : CH7 00007 : CH8
00008 : CH9
**
(3) : Error type
*****
(1) : 00480 ~ 00488
00480 : 1 00481 : 2
00482 : 3 00483 : 4
00484 : 5 00485 : 6
00486 : 7 00487 : 8
00488 : 9
*****
(2) : 00000 ~ 00008
00000 : CH1 00001 : CH2
00002 : CH3 00004 : CH4
00005 : CH5 00005 : CH6
00006 : CH7 00007 : CH8
00008 : CH9
**
(3) : Error type
*****
(1) : 00489
*****
(2) :
00001 : 4ab 00002 : 4abc
**
(3) : Error type
*****
(1) : 00512 ~ 00521
00512 : SEQ. 1 00513 : SEQ. 2
00514 : SEQ. 3 00515 : SEQ. 4
00516 : SEQ. 5 00517 : SEQ. 6
00518 : SEQ. 7 00519 : SEQ. 8
00520 : SEQ. 9 00521 : SPLIT 4
*****
(2) : 00000 ~ 00030 (second)
**
(3) : Error type
*****
(1) : 00339
*****
(2) :
00000 : OFF 00001 : ON
**
(3) : Error type
*****
(1) : 00528 ~ 00536
00528 : 1 00529 : 2
00530 : 3 00531 : 4
00532 : 5 00533 : 6
00534 : 7 00535 : 8
00536 : 9
*****
(2) :
00000 : OFF 00001 : ON
**
(3) : Error type
*****
(1) : 00544
*****
(2) :
00000 : OFF 00001 : ON
**
(3) : Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

67
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [Direct operation specification] menu setting system command form
<MOTION DETECTION SETTINGS>
<Menu setting>
DW,*****
(1)
*****
(2)
<Inquiry for setting information>
DR,*****
(1)
SELECTION
CAMERA NUMBER
DETECTION
MASK SETTING
SENSITIVITY
MOTION THRESHOLD
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****
(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****
(2)
*****
(1)
: 00576 ~ 00584
00576 : CH1 00577 : CH2
00578 : CH3 00579 : CH4
00580 : CH5 00581 : CH6
00582 : CH7 00583 : CH8
00585 : CH9
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
*****
(1)
: 00656 ~ 02383
00656 ~ 00847 : CH1 00848 ~ 01039 : CH2
01040 ~ 01231 : CH3 01232 ~ 01423 : CH4
01424 ~ 01615 : CH5 01616 ~ 01807 : CH6
01808 ~ 01999 : CH7 02000 ~ 02191 : CH8
02192 ~ 02383 : CH9
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
*****
(1)
: 00608 ~ 00616
00608 : CH1 00609 : CH2
00610 : CH3 00611 : CH4
00612 : CH5 00613 : CH6
00614 : CH7 00615 : CH8
00616 : CH9
*****
(2)
: 00000 ~ 00004
00000 : HIGH •••••LOW 00001 : HIGH ••••< LOW
00002 : HIGH •••< < LOW 00003 : HIGH ••< < < LOW
00004 : HIGH < < < < < LOW
**
(3)
: Error type
*****
(1)
: 00624 ~ 00632
00624 : CH1 00625 : CH2
00626 : CH3 00627 : CH4
00628 : CH5 00629 : CH6
00630 : CH7 00631 : CH8
00632 : CH9
*****
(2)
: 00001 ~ 00192 (POINT)
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

68
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] menu setting system command form
<RECORD SETTINGS>
<Menu setting>
DW,*****
(1)*****(2)
<Inquiry for setting information>
DR,*****
(1)
RECORD SETTING
PPS
RECORD SETTING
GRADE
RECORD SETTING
A-PPS
RECORD SETTING
A-GRADE
RECORD SETTING
ALARM MODE
RECORD SETTING
ALARM REC
DURATION
RECORD SETTING
PRE ALARM REC
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****(2)
*****(1)
: 04032 ~ 04040
04032 : CH1 04033 : CH2
04034 : CH3 04035 : CH4
04036 : CH5 04037 : CH6
04038 : CH7 04039 : CH8
04040 : CH9
*****
(2)
:
65535 :
- - - - -
00001 : 25P 00002 : 12.5P
00003 : 8.333P 00004 : 6.25P
00005 : 5P 00006 : 4.167P
00008 : 3.125P 00010 : 2.5P
00025 : 1P 00050 : 0.5P
00100 : 0.25P 00200 : 0.125P
**
(3)
: Error type
*****
(1)
: 04064 ~ 04072
04064 : CH1 04065 : CH2
04066 : CH3 04067 : CH4
04068 : CH5 04069 : CH6
04070 : CH7 04071 : CH8
04072 : CH9
*****
(2)
:
00000 : SUPER 00001 : HIGH
00002 : STD(STANDARD)
00003 : BASIC
00004 : LONG
**
(3)
: Error type
*****
(1)
: 04048 ~ 04056
04048 : CH1 04049 : CH2
04050 : CH3 04051 : CH4
04052 : CH5 04053 : CH6
04054 : CH7 04055 : CH8
04056 : CH9
*****
(2)
:
65535 :
- - - - -
00001 : 25P 00002 : 12.5P
00003 : 8.333P 00004 : 6.25P
00005 : 5P 00006 : 4.167P
00008 : 3.125P 00010 : 2.5P
00025 : 1P 00050 : 0.5P
00100 : 0.25P 00200 : 0.125P
**
(3)
: Error type
*****
(1)
: 04080 ~ 04088
04080 : CH1 04081 : CH2
04082 : CH3 04083 : CH4
04084 : CH5 04085 : CH6
04086 : CH7 04087 : CH8
04088 : CH9
*****
(2)
:
00000 : SUPER 00001 : HIGH
00002 : STD(STANDARD)
00003 : BASIC
00004 : LONG
**
(3)
: Error type
*****
(1)
: 05283
*****
(2)
:
00000 : ALL 00001 : ALARM
00002 : ALARM PLUS
**
(3)
: Error type
*****
(1)
: 03985
*****
(2)
: 00000 ~ 03600
00000 : MANUAL 00002 : 2S
00005 : 5S 00010 : 10S
00015 : 15S 00030 : 30S
00045 : 45S 00060 : 1M
00120 : 2M 00300 : 5M
00600 : 10M 01200 : 20M
01800 : 30M 03600 : 60M
**
(3)
: Error type
*****
(1)
: 03986
*****
(2)
: 00001 ~ 00003,00255
00001 : SHORT 00002 : MEDIUM
00003 : LONG 00255 : OFF
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

69
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [Direct operation specification] menu setting system command form
<TIMER PROGRAM SETTINGS>
<Menu setting>
DW,*****
(1)
*****
(2)
<Inquiry for setting information>
DR,*****
(1)
<Menu setting>
DW01,**
(1)
*****
(2)
*****
(3)
*****
(4)
*****
(5)
*****
(6)
*****
(7)
*****
(8)
<Inquiry for setting information>
DR01,**
(1)
<Menu setting>
DW,*****
(1)
*****
(2)
<Inquiry for setting information>
DR,*****
(1)
SELECTED PATTERN
TIMER PROGRAM
TIMER PROGRAM
SETTINGS
ALARM MODE
TIMER PROGRAM
SETTINGS
DAY OF THE WEEK
START DAY
TIMER PROGRAM
SETTINGS
DAY OF THE WEEK
END DAY
HOLIDAY SETTING
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****
(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****
(2)
<Writing of menu information>
RC EX,**
(9)
DW01,**
(1)
*****
(2)
*****
(3)
*****
(4)
*****
(5)
*****
(6)
*****
(7)
*****
(8)
<Reading of menu information>
RC EX,**
(9)
DR01,**
(1)
*****
(2)
*****
(3)
*****
(4)
*****
(5)
*****
(6)
*****
(7)
*****
(8)
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****
(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****
(2)
*****
(1)
: 04112
*****
(2)
:
00000 : P1 00001 : P2
00002 : P3
**
(3)
: Error type
*****
(1)
: PROGRAM NUMBER
00 : P1 - 1 01 : P1 - 2 02 : P1 - 3
03 : P1 - 4 04 : P1 - 5 05 : P1 - 6
06 : P1 - 7 07 : P1 - 8 08 : P2 - 1
09 : P2 - 2 10 : P2 - 3 11 : P2 - 4
12 : P2 - 5 13 : P2 - 6 14 : P2 - 7
15 : P2 - 8 16 : P3 - 1 17 : P3 - 2
18 : P3 - 3 19 : P3 - 4 20 : P3 - 5
21 : P3 - 6 22 : P3 - 7 23 : P3 - 8
*****
(2)
: Day of the week
00000 : SUN 00001 :MON 00002 :TUE
00003 :WED 00004 :THU 00005 : FRI
00006 : SAT 00128 : DAY 00129 : SPL
00130 : HOL 00255 : - - -
*****
(3)
: Start time (Hour)
00000 ~ 00023 (Hour) 00255 : - - -
*****
(4)
: Start time (Minute)
00000 ~ 00059 (Time) 00255 : - - -
*****
(5)
: End time (Hour)
00000 ~ 00023 (Hour) 00255 : - - -
*****
(6)
: End time (Minute)
00000 ~ 00059 (Time) 00255 : - - -
*****
(7)
: Selected pattern
00001 : A 00002 : B 00003 : C
00004 : C 00016 : SKIP 00255 : - - -
*****
(8)
: Motion detection setting
00000 : OFF 00001 : ON 00255 : - - -
**
(9)
: Error type
*****
(1)
: 05284 ~ 05287
05284 : A 05285 : B
05286 : C 05287 : D
*****
(2)
:
00000 : ALL 00001 : ALARM
00002 : ALARM PLUS
**
(3)
: Error type
*****
(1)
: 04400 ~ 04402
04400 : P1 04401 : P2
04402 : P3
*****
(2)
:
00000 : SUN 00001 :MON 00002 :TUE
00003 :WED 00004 :THU 00005 : FRI
00006 : SAT
**
(3)
: Error type
*****
(1)
: 04416 ~ 04418
04416 : P1 04417 : P2
04418 : P3
*****
(2)
:
00000 : SUN 00001 :MON 00002 :TUE
00003 :WED 00004 :THU 00005 : FRI
00006 : SAT
**
(3)
: Error type
*****
(1)
: 04432 ~ 04471
04432 : Month 04433 : Date (1 - 1)
04434 : Month 04435 : Date (1 - 2)
04436 : Month 04437 : Date (1 - 3)
04438 : Month 04439 : Date (1 - 4)
04440 : Month 04441 : Date (2 - 1)
04442 : Month 04443 : Date (2 - 2)
04444 : Month 04445 : Date (2 - 3)
04446 : Month 04447 : Date (2 - 4)
04448 : Month 04449 : Date (3 - 1)
04450 : Month 04451 : Date (3 - 2)
04452 : Month 04453 : Date (3 - 3)
04454 : Month 04455 : Date (3 - 4)
04456 : Month 04457 : Date (4 - 1)
04458 : Month 04459 : Date (4 - 2)
04460 : Month 04461 : Date (4 - 3)
04462 : Month 04463 : Date (4 - 4)
04464 : Month 04465 : Date (5 - 1)
04466 : Month 04467 : Date (5 - 2)
04468 : Month 04469 : Date (5 - 3)
04470 : Month 04471 : Date (5 - 4)
*****
(2)
:
Month : 00001 ~ 00012 00025 : NONE
Date :00001 ~ 00031 00025 : NONE
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#2
#2
#2
#2
#1
#1
#1
#1
#2
#2
#2
#2
#1
#1

70
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] menu setting system command form
<TIMER PROGRAM SETTINGS> (Continued)
<Menu setting>
DW,*****
(1)*****(2)
<Inquiry for setting information>
DR,*****
(1)
TIMER PROGRAM
SETTINGS
REC MODE
TIMER PROGRAM
SETTINGS
PPS
TIMER PROGRAM
SETTINGS
GRADE
TIMER PROGRAM
SETTINGS
A-PPS
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****(2)
*****(1)
:
04480 : A 04482 : B
04484 : C 04486 : D
*****
(2)
:
00000 : NORMAL & ALARM
00001 : PRE ALARM
**
(3)
: Error type
*****
(1)
: 04560 ~ 04595
04560 : A - CH1 04561 : A - CH2 04562 : A - CH3
04563 : A - CH4 04564 : A - CH5 04565 : A - CH6
04566 : A - CH7 04567 : A - CH8 04568 : A - CH9
04569 : B - CH1 04570 : B - CH2 04571 : B - CH3
04572 : B - CH4 04573 : B - CH5 04574 : B - CH6
04575 : B - CH7 04576 : B - CH8 04577 : B - CH9
04578 : C - CH1 04579 : C - CH2 04580 : C - CH3
04581 : C - CH4 04582 : C - CH5 04583 : C - CH6
04584 : C - CH7 04585 : C - CH8 04586 : C - CH9
04587 : D - CH1 04588 : D - CH2 04589 : D - CH3
04590 : D - CH4 04591 : D - CH5 04592 : D - CH6
04593 : D - CH7 04594 : D - CH8 04595 : D - CH9
*****
(2)
:
65535 :
- - - - -
00001 : 25P 00002 : 12.5P
00003 : 8.333P 00004 : 6.25P
00005 : 5P 00006 : 4.167P
00008 : 3.125P 00010 : 2.5P
00025 : 1P 00050 : 0.5P
00100 : 0.25P 00200 : 0.125P
**
(3)
: Error type
*****
(1)
: 04688 ~ 04723
04688 : A - CH1 04689 : A - CH2 04690 : A - CH3
04691 : A - CH4 04692 : A - CH5 04693 : A - CH6
04694 : A - CH7 04695 : A - CH8 04696 : A - CH9
04697 : B - CH1 04698 : B - CH2 04699 : B - CH3
04700 : B - CH4 04701 : B - CH5 04702 : B - CH6
04703 : B - CH7 04704 : B - CH8 04705 : B - CH9
04706 : C - CH1 04707 : C - CH2 04708 : C - CH3
04709 : C - CH4 04710 : C - CH5 04711 : C - CH6
04712 : C - CH7 04713 : C - CH8 04714 : C - CH9
04715 : D - CH1 04716 : D - CH2 04717 : D - CH3
04718 : D - CH4 04719 : D - CH5 04720 : D - CH6
04721 : D - CH7 04722 : D - CH8 04723 : D - CH9
*****
(2)
:
00000 : SUPER 00001 : HIGH
00002 : STD(STANDARD)
00003 : BASIC
00004 : LONG
**
(3)
: Error type
*****
(1)
: 04624 ~ 04659
04624 : A - CH1 04625 : A - CH2 04626 : A - CH3
04627 : A - CH4 04628 : A - CH5 04629 : A - CH6
04630 : A - CH7 04631 : A - CH8 04632 : A - CH9
04633 : B - CH1 04634 : B - CH2 04635 : B - CH3
04636 : B - CH4 04637 : B - CH5 04638 : B - CH6
04639 : B - CH7 04640 : B - CH8 04641 : B - CH9
04642 : C - CH1 04643 : C - CH2 04644 : C - CH3
04645 : C - CH4 04646 : C - CH5 04647 : C - CH6
04648 : C - CH7 04649 : C - CH8 04650 : C - CH9
04651 : D - CH1 04652 : D - CH2 04653 : D - CH3
04654 : D - CH4 04655 : D - CH5 04656 : D - CH6
04657 : D - CH7 04658 : D - CH8 04659 : D - CH9
*****
(2)
:
65535 :
- - - - -
00001 : 25P 00002 : 12.5P
00003 : 8.333P 00004 : 6.25P
00005 : 5P 00006 : 4.167P
00008 : 3.125P 00010 : 2.5P
00025 : 1P 00050 : 0.5P
00100 : 0.25P 00200 : 0.125P
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

71
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [Direct operation specification] menu setting system command form
<TIMER PROGRAM SETTINGS> (Continued)
<Menu setting>
DW,
*****(1)*****(2)
<Inquiry for setting information>
DR,
*****(1)
TIMER PROGRAM
SETTINGS
A-GRADE
TIMER PROGRAM
SETTINGS
ALARM REC
DURATION
TIMER PROGRAM
SETTINGS
PRE ALARM REC
<Writing of menu information>
RC EX,
**(3)
DW,
*****(1)
*****(2)
<Reading of menu information>
RC EX,
**(3)
DR,
*****(1)
*****(2)
*****(1)
: 04752 ~ 04787
04752 : A - CH1 04753 : A - CH2 04754 : A - CH3
04755 : A - CH4 04756 : A - CH5 04757 : A - CH6
04758 : A - CH7 04759 : A - CH8 04760 : A - CH9
04761 : B - CH1 04762 : B - CH2 04763 : B - CH3
04764 : B - CH4 04765 : B - CH5 04766 : B - CH6
04767 : B - CH7 04768 : B - CH8 04769 : B - CH9
04770 : C - CH1 04771 : C - CH2 04772 : C - CH3
04773 : C - CH4 04774 : C - CH5 04775 : C - CH6
04776 : C - CH7 04777 : C - CH8 04778 : C - CH9
04779 : D - CH1 04780 : D - CH2 04781 : D - CH3
04782 : D - CH4 04783 : D - CH5 04784 : D - CH6
04785 : D - CH7 04786 : D - CH8 04787 : D - CH9
*****(2)
:
00000 : SUPER 00001 : HIGH
00002 : STD(STANDARD)
00003 : BASIC
00004 : LONG
**(3)
: Error type
*****(1)
: 04102
*****(2)
: 00000 ~ 03600
00000 : MAN 00002 : 2S
00005 : 5S 00010 : 10S
00015 : 15S 00030 : 30S
00045 : 45S 00060 : 1M
00120 : 2M 00300 : 5M
00600 : 10M 01200 : 20M
01800 : 30M 03600 : 60M
**(3)
: Error type
*****(1)
: 04103
*****(2)
: 00001 ~ 00003
00001 : SHORT 00002 : MEDIUM
00003 : LONG
**(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

72
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] menu setting system command form
<INITIAL SET UP/INFORMATION>
<Menu setting>
DW,*****
(1)
*****
(2)
<Inquiry for setting information>
DR,*****
(1)
HDD REPEAT REC
HDD REPEAT PLAY
IM-CHECK PLAY
SEQUENTIAL PLAY
AUDIO RECORDING
MODE OUT
KEY SOUND
BUZZER
REMAIN HDD
DEVICE
REMAIN HDD
HDD REMAIN
EMERGENCY
REC DURATION
HDD FULL
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****
(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****
(2)
*****
(1)
: 04832
*****
(2)
:
00000 : OFF 00001 : ON
00002 : STANDBY
**
(3)
: Error type
*****
(1)
: 04834
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
*****
(1)
: 04821
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
*****
(1)
: 04822
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
*****
(1)
: 04817
*****
(2)
:
00000 : OFF 00001 : ON 00002 : ALARM
**
(3)
: Error type
*****
(1)
: 04848 ~ 04851
04848 : MODE OUT 1 04849 : MODE OUT 2
04850 : MODE OUT 3 04851 : MODE OUT 4
*****
(2)
:
00000 : OFF 00001 : REC
00002 : PLAY 00003 : REMAIN
00004 : POWR 00006 : MOTION
00009 : ALARM
**
(3)
: Error type
*****
(1)
: 04853
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
*****
(1)
: 04855
*****
(2)
:
00000 : OFF 00001 : REMAIN
00002 :WARNING 00003 :ALARM
**
(3)
: Error type
*****
(1)
: 04864
*****
(2)
:
00000 : OFF 00001 : HDD
**
(3)
: Error type
*****
(1)
: 04865
*****
(2)
:
00002 : 2% 00004 : 4%
00006 : 6% 00008 : 8%
00010 : 10% 00015 : 15%
00020 : 20% 00030 : 30%
00040 : 40% 00050 : 50%
**
(3)
: Error type
*****
(1)
: 04880
*****
(2)
:
00002 : 2% 00004 : 4%
00006 : 6% 00008 : 8%
00010 : 10% 00015 : 15%
00020 : 20% 00030 : 30%
00040 : 40% 00050 : 50%
00255 : OFF
**
(3)
: Error type
*****
(1)
: 04102
*****
(2)
: 00000 ~ 03600
00060 : 1M 00120 : 2M
00300 : 5M 00600 : 10M
01200 : 20M 01800 : 30M
03600 : 60M
**
(3)
: Error type
*****
(1)
: 05360
*****
(2)
:
00000 : OFF 00001 : ON
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

73
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [Direct operation specification] menu setting system command form
<INITIAL SET UP/INFORMATION> (Continued)
<Menu setting>
DW,
*****
(1)
*****
(2)
<Inquiry for setting information>
DR,
*****
(1)
RS-232C
MODE
RS-232C
SETTINGS
TRANSMISSION RATE
RS-233C
SETTINGS
DATA BIT LENGTH
RS-232C
SETTINGS
PARITY BIT
RS-232C
SETTINGS
STOP BIT LENGTH
RS-232C
SETTINGS
DELIMITER
<Writing of menu information>
RC EX,
**
(3)
DW,
*****
(1)
*****
(2)
<Reading of menu information>
RC EX,
**
(3)
DR,
*****
(1)
*****
(2)
*****
(1)
: 04896
*****
(2)
:
00000 : OFF 00001 : REMOTE A
00002 : REMOTE B
**
(3)
: Error type
*****
(1)
: 04912
*****
(2)
:
01200 : 1200 02400 : 2400
04800 : 4800 09600 : 9600
19200 : 19200
**
(3)
: Error type
*****
(1)
: 04913
*****
(2)
:
00007 : 7 BIT 00008 : 8 BIT
**
(3)
: Error type
*****
(1)
: 04914
*****
(2)
:
00000 : NONE 00001 : ODD
00002 : EVEN
**
(3)
: Error type
*****
(1)
: 04915
*****
(2)
:
00001 : 1 BIT 00002 : 2 BIT
**
(3)
: Error type
*****
(1)
: 04916
*****
(2)
:
00000 : CR 00001 : CR•LF
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1

74
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] menu setting system command form
<SEARCH>
Refer to the playback of [Direct operation specification] operation setting system command form for search execution.
<Menu setting>
DW,*****
(1)*****(2)
<Inquiry for setting information>
DR,*****
(1)
<Inquiry for setting information>
DR,*****
(1)
<Menu setting>
DW,*****
(1)*****(2)
<Inquiry for setting information>
DR,*****
(1)
TIME DATE SEARCH
INDEX SEARCH
ALARM INDEX
SEARCH
ALARM LIST SEARCH
DATE/TIME
SEARCH TYPE
PLAY DEVICE
SELECTION
CAMERA NO.
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****(2)
<Writing of menu information>
RC EX,**
(3)
DW,*****
(1)
*****(2)
<Reading of menu information>
RC EX,**
(3)
DR,*****
(1)
*****(2)
*****(1)
:
05044 : Search time (Year) 05045 : Search time (Month)
05046 : Search time (Day) 05047 : Search time (Hour)
05048 : Search time (Minute) 05049 : Search time (Second)
*****
(2)
:
Year : 00001 ~ 00099 Month : 00001 ~ 00012
Day :00001 ~ 00031 Hour : 00001 ~ 00023
Minute : 00000 ~ 00059 Second : 00000 ~ 00059
**
(3)
: Error type
*****
(1)
: 05072
*****
(2)
: 00001 ~ 00099
**
(3)
: Error type
*****
(1)
: 05088
*****
(2)
: 00001 ~ 00099
**
(3)
: Error type
*****
(1)
:
05060 : List time mask (Year) 05061 : List time mask (Month)
05062 : List time mask (Day) 05063 : List time mask (Hour)
05064 : List time mask (Minute) 05065 : List time mask (Second)
*****
(2)
:
Year : 00001 ~ 00099 Month : 00001 ~ 00012
Day :00001 ~ 00031 Hour : 00001 ~ 00023
Minute : 00000 ~ 00059 Second : 00000 ~ 00059
None mask : 00238
**
(3)
: Error type
*****
(1)
: 05057
*****
(2)
:
00000 :TIME DATE 00001 : INDEX
00002 : ALARM INDEX 00003 : ALARM SKIP
00004 : ALARM LIST
**
(3)
: Error type
*****
(1)
: 05056
*****
(2)
:
00001 : HDD
00003 : CFC
**
(3)
: Error type
*****
(1)
: 05058
*****
(2)
:
00000 : CH1 00001 : CH2
00002 : CH3 00003 : CH4
00004 : CH5 00005 : CH6
00006 : CH7 00007 : CH8
00008 : CH9 00032 : ALL
**
(3)
: Error type
Menu Commands NotesStatus
#2
#2
#2
#2
#1
#1
#2
#2
#1
#2
#2
#2
#2
#1
#1

75
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [Direct operation specification] menu setting system command form
<COPY>
<Inquiry for setting information>
DR,
*****
(1)
<Menu setting>
DW,
*****
(1)
*****
(2)
<Inquiry for setting information>
DR,
*****
(1)
COPY
DIRECTION
COPY
MODE
COPY
START/END
COPY
TRANSFER PERIOD
RESTORE
MODE
RESTORE
START/END
RESTORE
TRANSFER PERIOD
<Reading of menu information>
RC EX,
**
(3)
DR,
*****
(1)
*****
(2)
<Writing of menu information>
RC EX,
**
(3)
DW,
*****
(1)
*****
(2)
<Reading of menu information>
RC EX,
**
(3)
DR,
*****
(1)
*****
(2)
*****
(1)
: 05120
*****
(2)
:
00000 : HDD CFC 00001 : CFC HDD
**
(3)
: Error type
*****
(1)
: 05121
*****
(2)
:
00000 : OVERWRITE 00001 : FIFO
**
(3)
: Error type
*****
(1)
:
05136 : Copy start time (Year)
05137 : Copy start time (Month)
05138 : Copy start time (Day)
05139 : Copy start time (Hour)
05140 : Copy start time (Minute)
05141 : Copy start time (Second)
05142 : Copy end time (Year)
05143 : Copy end time (Month)
05144 : Copy end time (Day)
05145 : Copy end time (Hour)
05146 : Copy end time (Minute)
05147 : Copy end time (Second)
*****
(2)
:
Year : 00001 ~ 00099 Month : 00001 ~ 00012
Day :00001 ~ 00031 Hour : 00001 ~ 00023
Minute : 00000 ~ 00059 Second : 00000 ~ 00059
**
(3)
: Error type
*****
(1)
: 05126
*****
(2)
:
00000 : START•END 00001 : START
**
(3)
: Error type
*****
(1)
: 05152
*****
(2)
:
00000 : OVERWRITE 00001 : FIFO
**
(3)
: Error type
*****
(1)
:
05168 : Restore start time (Year)
05169 : Restore start time (Month)
05170 : Restore start time (Day)
05171 : Restore start time (Hour)
05172 : Restore start time (Minute)
05173 : Restore start time (Second)
05174 : Restore end time (Year)
05175 : Restore end time (Month)
05176 : Restore end time (Day)
05177 : Restore end time (Hour)
05178 : Restore end time (Minute)
05179 : Restore end time (Second)
*****
(2)
:
Year : 00001 ~ 00099 Month : 00001 ~ 00012
Day :00001 ~ 00031 Hour : 00001 ~ 00023
Minute : 00000 ~ 00059 Second : 00000 ~ 00059
**
(3)
: Error type
*****
(1)
: 05126
*****
(2)
:
00000 : START•END 00001 : START
**
(3)
: Error type
NotesStatus
Menu Commands
#2
#2
#2
#2
#1
#1
#2
#2
#1

76
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C [Direct operation specification] menu setting system command form
<ANOTHER SETTINGS>
<Inquiry for setting information>
DR,*****
(1)
MD?
ME?
UTO?
COMD,**
(1)**(2)*******
****************
*********(3)
COMS,**
(1)
DC
RECORDING
PATTERN
CHECK THE
CONDITION
CHECK THE
CONDITION
ACQUIRE THE
ELAPSED TIME
WRITE COMMENT
DATA INFORMATION
WRITE COMMENT
DELETE THE
COMMENT DISPLAY
<Writing of menu information>
RC EX,**
(3)
DR,*****
(1)
*****(2)
RC
EX,**
(26)
MD,**
(1)**(2)**(3)**(4)
**(5)****(6)**(7)**(8)**(9)
**(10)**(11)**(12)**(13)**(14)
**(15)**(16)**(17)**(18)**(19)
**(20)**(21)**(22)**(23)**(24)
**(25)
(Each status corresponds to the last two
digits of each operating mode within
the condition change notification system.)
RC
EX,**
(26)
ME,**
(1)**(2)**(3)**(4)
**(5)****(6)**(7)**(8)**(9)
**(10)**(11)**(12)**(13)**(14)
**(15)**(16)**(17)**(18)**(19)
**(20)**(21)**(22)**(23)**(24)
**(25)
(Each status corresponds to the last two
digits of each operating mode within
the condition change notification system.)
RC
EX,**
(2)
UTO?,*********
*
(1)
RC
EX,**
(4)
COMD,**
(1)**(2)*****
******************
*********(3)
RC
EX,**
(2)
COMS,**
(1)
RC
EX,**
(2)
00DC
*****
(1)
: 05268
*****
(2)
:
00000 : NORMAL
**
(3)
: Error type
**
(1)
: System condition
**
(2)
: Key lock condition
**
(3)
: Remote / local condition
**
(4)
:Timer condition
**
(5)
: Alarm interrupt condition
****
(6)
: Menu condition
**
(7)
: Recording condition
**
(8)
: Playback condition
**
(9)
: Display condition
**
(10)
: Motion detection condition
**
(11)
: Back up condition
**
(12)
: Copy condition
**
(13)
: Restore condition
**
(14)
: Device control condition
**
(15)
: Acquire information condition
**
(16)
: Delete device condition
**
(17)
: Data reset condition
**
(18) ~ **(25)
: Reserved
**
(26)
: Error type
**
(1)
: System condition
**
(2)
: Key lock condition
**
(3)
: Remote / local condition
**
(4)
:Timer condition
**
(5)
: Alarm interrupt condition
****
(6)
: Menu condition
**
(7)
: Recording condition
**
(8)
: Playback condition
**
(9)
: Display condition
**
(10)
: Motion detection condition
**
(11)
: Back up condition
**
(12)
: Copy condition
**
(13)
: Restore condition
**
(14)
: Device control condition
**
(15)
: Acquire information condition
**
(16)
: Delete device condition
**
(17)
: Data reset condition
**
(18) ~ **(25)
: Reserved
**
(26)
: Error type
(When there is a lag in response time of the unit during
condition change, sending this command will read RS-232C
status after readying the unit for response by clearing
all remaining commands in the reception buffer.)
**********
(1)
: Elapsed time
0000000000 ~ 9999999999 (Hour)
**
(2)
: Error type
**
(1)
: Camera number
00 : CH1 01 : CH2 02 :CH3 03 : CH4 04 : CH5
05 : CH6 06 : CH7 07 : CH8 08 : CH9
**
(2)
: Character size (00 - 32)
*****************************
***
(3)
: Comment
**
(4)
: Error type
**
(1)
: Camera number
00 : CH1 01 : CH2 02 :CH3 03 : CH4 04 : CH5
05 : CH6 06 : CH7 07 : CH8 08 : CH9
**
(2)
: Error type
NotesStatus
Menu Commands
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#1
#1
#2
#2
#1
#2
#2
#2
#2
#1

77
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
• RS-232C [False operation panel] command form
KKP0
KKR0
KKR1
KKB0
KKB1
KKB2
KKB4
KKT0
KKT1
KKZ
KKE
KKD01
KKD02
KKD03
KKD04
KKD05
KKD06
KKD07
KKD08
KKD09
KKL0
KKL5
KKM
KKC
KKK0
KKW0
KKW5
KKA
KKJ0
KKJ1
KKS00
KKS01
KKS02
KKS03
KKS04
KKS11
KKS12
KKS13
KKS14
POWER
REC/STOP
STOP
PLAY
REV.PLAY
(REVERSE PLAY)
PAUSE
TIMER
ZOOM
SPLIT/SEQUENCE
Camera number
LOCK
SET UP
COPY
SEARCH
WARNING RESET
ALARM INTERRUPT
JOG
SHUTTLE
RC
EX,**
(2)
KKP0
RC
EX,**
(2)
KKR0
RC
EX,**
(2)
KKR1
RC
EX,**
(2)
KKB0
RC
EX,**
(2)
KKB1
RC
EX,**
(2)
KKB2
RC
EX,**
(2)
KKB4
RC
EX,**
(2)
KKT0
RC
EX,**
(2)
KKT1
RC
EX,**
(2)
KKZ
RC
EX,**
(2)
KKE
RC
EX,**
(2)
KKD01
RC
EX,**
(2)
KKD02
RC
EX,**
(2)
KKD03
RC
EX,**
(2)
KKD04
RC
EX,**
(2)
KKD05
RC
EX,**
(2)
KKD06
RC
EX,**
(2)
KKD07
RC
EX,**
(2)
KKD08
RC
EX,**
(2)
KKD09
RC
EX,**
(2)
KKL0
RC
EX,**
(2)
KKL5
RC
EX,**
(2)
KKM
RC
EX,**
(2)
KKC
RC
EX,**
(2)
KKK0
RC
EX,**
(2)
KKW0
RC
EX,**
(2)
KKW5
RC
EX,**
(2)
KKA
RC
EX,**
(2)
KKJ0
RC
EX,**
(2)
KKJ1
RC
EX,**
(2)
KKS00
RC
EX,**
(2)
KKS01
RC
EX,**
(2)
KKS02
RC
EX,**
(2)
KKS03
RC
EX,**
(2)
KKS04
RC
EX,**
(2)
KKS11
RC
EX,**
(2)
KKS12
RC
EX,**
(2)
KKS13
RC
EX,**
(2)
KKS14
POEWR ON/OFF
**
(2)
: Error type
RECORDING
STOP RECORDING
**
(2)
: Error type
STOP PLAYBACK
**
(2)
: Error type
PLAYBACK
**
(2)
: Error type
REVERSE PLAYBACK
**
(2)
: Error type
PAUSE
**
(2)
: Error type
TIMER ON
TIMER OFF
**
(2)
: Error type
ZOOM
**
(2)
: Error type
SPLIT / SEQUENCE
**
(2)
: Error type
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
**
(2)
: Error type
SIMPLE LOCK
PASSWORD LOCK
**
(2)
: Error type
MENU
**
(2)
: Error type
COPY
**
(2)
: Error type
SEARCH
**
(2)
: Error type
WARNING RESET
WARNING RESET 5 second pressing
**
(2)
: Error type
ALARM INTERRUPT
**
(2)
: Error type
JOG right turn
JOG left turn
**
(2)
: Error type
SHUTTLE center
SHUTTLE right 1
SHUTTLE right 2
SHUTTLE right 3
SHUTTLE right 4
SHUTTLE left 1
SHUTTLE left 2
SHUTTLE left 3
SHUTTLE left 4
**
(2)
: Error type
(Send SHUTTLE center command before send this command.)
Button Commands NotesStatus

78
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
• RS-232C Status condition change information system
System mode
Timer mode
Alarm disable mode
Recording mode
Playback mode
Display mode
Motion detection mode
Copy mode
Restore mode
Acquire the information
mode
Data delete mode
Inform the NO SIGNAL
condition
Inform the error
warning
Inform the data
falsification error
Inform the renewal of
Alarm number
Inform the position
EX,AA,
****(1)
EX,AB11,
*************
******************
*(1)
EX,AB,
**(1)
EX,AB51,
**(1)
EX,AC11,
*****(1)
EX,AC,
**(1)
,
***(2)
****(1)
: System mode
0100 : Power off 0103 : Power on
0106 : Setting menu 0107 :Copy menu
0108 : Search menu 0109 : Device unusual situation
010A : Device initialize 010B :Device reconstruction
010F : System unusual situation
****(1)
:Timer mode
0500 :Timer off 0501 :Timer on
0502 :Timer error
****(1)
: Alarm disable mode
0600 : Alarm disable off 0601 : Alarm disable on
****(1)
: Recording mode
0800 : Stop 0803 : Stop(pause)
0804 : Recording 0805 : Pre alarm recording
0806 : Alarm recording during pause
0807 : Alarm recording during recording
0808 : Alarm recording during Pre alarm recording
080A : Recording error
****(1)
: Playback mode
0900 : Stop 0903 : Playback (1)
0904 : Reverse playback (1) 0905 :Playback pause (1)
0906 : Reverse playback pause (1) 0907 :Forward speed search (1)
0908 : Reverse speed search (1) 0909 : Fast forward (1)
090A : Rewind (1) 090B : Playback (2)
090C : Reverse playback (2) 090D : Playback pause (2)
090E : Reverse playback pause (2) 090F : Forward speed search (2)
0910 : Reverse speed search (2) 0911 : Fast forward (2)
0912 : Rewind (2) 0913 :Playback (3)
0914 : Reverse playback (3) 0915 :Playback pause (3)
0916 : Reverse playback pause (3) 0917 :Forward speed search (3)
0918 : Reverse speed search (3) 0919 : Fast forward (3)
091A : Rewind (3) 091C : Playback error
(1) : Single screen , (2) : Split display, (3) :Zoom
****(1)
: Display mode
0A07 : Display error
****(1)
: Motion detection mode
0B05 : Motion detection error
****(1)
: Copy mode
0D00 : Stop 0D02 : Execute
0D04 : Copy error
****(1)
: Restore mode
0E00 : Stop 0E02 : Execute
0E04 : Restore error
****(1)
: Acquire information mode
1000 : Done 1002 : Acquire information
****(1)
: Data delete mode
2000 : Done 2002 : Data delete error
******************************
**(1)
: Information the NO SIGNAL condition
Output the NO SIGNAL condition (3 : Having signal, 2 : Judge having signal
1 : Judge not having signal, 0 : Not having signal) about 9CH(32CH) when
the condition changes.But this information is effective to the camera which is
recording, so the information about the camera whitch is not recording is
indefinite.
**(1)
:
12 : REC R/W ERROR
13 : REC SYSTEM ERROR
32 : COPY R/W ERROR
33 : COPY SYSTEM ERROR
34 : COPY OVERWRITE ERROR
35 : COPY EARLY WARNING ERROR
36 : COPY OVERWRITE WARNING
42 : RESTORE R/W ERROR
43 : RESTORE SYSTEM ERROR
**(1)
: Camera number
*****(1)
: Renewal of Alarm number
(Output when the Alarm number is renewed.)
**(1)
: Position
12 : Main device recording position
32 : Copy device recording position
42 : Restore device recording position
***(2)
: 000 ~ 100 (%)
Mode NotesStatus
#2
#2
#2
#2
#2
#2