MLis MLB-Z4001 User manual

MLB-Z4001 Terminal User Manual 1 Rev 1.0
MLB-Z4001
Ethernet to 900 MHz
RF Modem
USER MANUAL

MLB-Z4001 Terminal User Manual 2 Rev 1.0
Information provided by Schmidt & Co., (HK) Ltd, (herein known as ‘the company’), is believed to be
accurate and reliable. However, the company assumes no responsibility for its use, nor any
infringement of patents or other rights of third parties, which may result from its use. No license is
granted by implication or otherwise under any patent rights of the company other than for circuitry
embodied in the company’s products. The company reserves the right to change the circuitry and
specifications at any time without notice. This document is subject to change without notice.
No part of this document may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including but not limited to photocopying, recording, transmitting via fax and/or modem
devices, scanning, and/or information storage and retrieval systems for any purpose without the
expressed written consent of the company.
WARNING: The MLiS GSM Terminal is a RF product intended for interfacing and operating with a host
device. Local relevant RF regulations such as allowed frequencies and usage in commercial flights
must be observed. Safety instructions must be included in the manuals of the host device. Schmidt &
Co., (HK) Ltd assumes NO liability for customers, who fail to comply with these precautions.
Service and Support
[e-mail]
Download Information
http://www.schmidtm2m.com/en/support_download.php

MLB-Z4001 Terminal User Manual 3 Rev 1.0
CONTENTS
1INTRODUCTION .....................................................................................................................................................5
1.1 Description...................................................................................................................................................5
1.2 Highlights......................................................................................................................................................5
1.3 Functional Block diagram.............................................................................................................................6
1.4 Main Features and Services .........................................................................................................................7
1.4.1 Terminal Features and Electrical Specifications ......................................................................................7
1.5 Precautions ..................................................................................................................................................8
2MECHANICAL DESCRIPTION ..................................................................................................................................9
2.1 Overview ......................................................................................................................................................9
2.2 Dimensions...................................................................................................................................................9
3ELECTRICAL INTERFACE DESCRIPTIONS...............................................................................................................10
3.1 Overview ....................................................................................................................................................10
3.2 Radio Interface (Type SMA Connector Female) - RF Antenna ...................................................................12
4OPERATING MODES.............................................................................................................................................13
4.1 Power on the Modem ................................................................................................................................13
4.2 Configuration Tool.............................................................................................................................................13
4.1.1 Data Connection Demo ( H/W & Software Installation) ………………………………………………………………..14
5SALES CONTACT...................................................................................................................................................31
6ORDER INFORMATION.........................................................................................................................................32

MLB-Z4001 Terminal User Manual 4 Rev 1.0
List of Figures
Figure 1: Functional Block Diagram for MLB-Z4001...................................................................................................6
Figure 2: Chassis Dimension for MLB-Z4001 ..............................................................................................................9
Figure 3: External Interfaces/Indicators for MLB-Z4001......................................................................................... 10
Figure 4: Antenna Connector for MLB-Z4001 ......................................................................................................... 12
List of Tables
Table 1: Operating Modes……………………………………………………………………………………………………………………………………7
Table 2: Features and Specifications..........................................................................................................................7
Table 3: Chassis Dimensions and Mechanical Description for MLB-Z4001................................................................9
Table 4: RS232 connector configuration for MLB-Z4001...…………………………………………………………………………….……11
Table 5 : Interfaces and Indicators Description of MLB-Z4001 ............................................................................... 13

MLB-Z4001 Terminal User Manual 5 Rev 1.0
1INTRODUCTION
1.1 Description
The MLiS MLB-Z4001 900HMZ ZigBee terminal is a compact terminal that is designed for wireless M2M
communications.
The MLB-Z4001 terminal uses the RJ45 Connector to provide data communication interface and the DC jack to
provide power input. LEDs are used to indicate the status of the terminal.
MLB-Z4001 is taking advantage of the specific Mesh networking protocol, featuring dense network operation
and supporting for sleeping routers, and are also available in a proprietary point-to-multipoint configuration.
The MLB-Z4001 terminal can be used to provide a wireless communications link for many applications, including
warehouse, building automation, and street light applications.
1.2 Highlights
Interface
•DC jack connector for power
•RJ45 connector for data communications
•SMA female connector (Antenna connector)
General Features
•ZigBee 902 to 928 MHZ, software selectable channel mask for interference immunity
•Supply voltage range: 5~32VDC
•Temperature range
-Operating: -40°C~+75°C
•Surge protection: IEC61000-4-5 LV1
•Casing Material: Metal
•Dimensions (L) x(W) X(H): 85 x 97 x 24mm (excluding connectors)
•Weight: 210g
•
Data Transmission
•RF Data Rate: 10 Kbps or 200 Kbps
•Indoor/Urban Range: up to 2000 foot (610 m)
•Outdoor/ Line-Of-Sight Range: Up to 9 miles (14 km) w/ dipole antenna;
Up to 28 miles (45 km) w/ high-gain antenna
•Transmit Power: Up to 24 dBm (250 mW) software selectable
•Receiver Sensitivity: -101 dBm @ 200 Kbps, -110 dBm @ 10 Kbps

MLB-Z4001 Terminal User Manual 6 Rev 1.0
1.3 Functional Block Diagram
Figure 1: Functional Block Diagram for MLB-Z4001
The MLB-Z4001 consists of a fully certified (CE approved).
The terminal is supplied with power via the DC jack connector. The RJ45 connector pins are used for
data communications.
The SMA female connector provides the air interface to an external 50 ohm antenna specified for the
correct frequency band.

MLB-Z4001 Terminal User Manual 7 Rev 1.0
1.4 Main Features and Services
The MLB-Z4001 performs a set of ZigBee services according. The services and functions of the MLB-
Z4001 are implemented by issuing customized applications embedded on the device, or over the RJ45
to Ethernet interface.
1.4.1 Terminal Features and Electrical Specifications
MLB-Z4001
General Features
Frequency Band
902 to 928 MHZ, software selectable channel mask for interference
immunity
Power input
5 to 32 VDC
Operating Temptation
-40°C~+75°C
ESD Protection
IEC61000-4-5 LV1
Dimension (L)x(W)x(H)
85mm x 97mm x 24mm (excluding connectors)
Weight
210g
Casing Material
Metal
Data Transmission
RF Data Rate
10 Kbps or 200 Kbps
Indoor/Urban Range
up to 2000ft (610m)
Outdoor/Line-of-Sight
Range
Up to 9 miles (14 km) w/ dipole antenna;
Up to 28 miles (45 km) w/ high-gain antenna
Transmit Power
Up to 24 dBm (250 mW) software selectable
Receiver Sensitivity
-101 dBm @ 200 Kbps, -110 dBm @ 10 Kbps
Special Features
Networking Topologies
Mesh, Repeater, Point-to-Point, Point-to-Multipoint, Peer-to-Peer
Spread Spectrum
FHSS (Software Selectable Channels)
Interfaces
RF Antenna Socket
50ohm SMA
Power Connector
DC jack Connector
Ethernet Interface
RJ45 connect for Ethernet (female)
LED
1 x for Power , 1 x for Tx\Rx, 1 x Ethernet Indicator
Reset
HW Reset
Approvals
CE
Yes
Table 1: Features and Specifications

MLB-Z4001 Terminal User Manual 8 Rev 1.0
1.5 Precautions
The MLB-Z4001 terminal is designed for indoor use only. For outdoor use it has to be integrated into a
weatherproof enclosure. Do not exceed the environmental and electrical limits as specified in the user
manual.

MLB-Z4001 Terminal User Manual 9 Rev 1.0
2MECHANICAL DESCRIPTION
2.1 Overview
The pictures below show the mechanical design of the terminal along with the positions of the different
connectors. The terminal case is made of durable PC/ABS plastic.
2.2 Dimensions
Figure 2: Chassis Dimension for MLB-Z4001
S/N
Parameter
Value
1
Height (H)
24mm
2
Length (L)
85mm
3
Width (W)
97mm
4
Weight
210g
5
Chassis Material
Metal
6
Mounting
Standard
Suitable for use with DIN Rail
Clips
Table 2: Chassis Dimensions and Mechanical Description for MLB-Z4001

MLB-Z4001 Terminal User Manual 10 Rev 1.0
3ELECTRICAL INTERFACE DESCRIPTIONS
3.1 Overview
1 2 3
Front/Back View
Figure 3: External Interfaces/Indicators for MLB-Z4001
The interfaces and indicators for MLB-Z4001 are as follows:
Item
Description
Function
1
DC-jack
For Power
2
Reset
HW-Reset-Key
3
RJ45
Signal Transmission Signal Trans

MLB-Z4001 Terminal User Manual 11 Rev 1.0
Table below defines the RJ45 pin configuration on the Terminal:
Pin No.
Signal Name
Function
1
Tx+
2
CT
VDD33A
3
Tx-
4
NC
5
NC
6
Rx+
7
CT
VDD33A
8
Rx-
9
LED1+
Indicator
10
LED1-
11
LED2+
Indicator
12
LED2-
Table 4: RJ45 Connector Configuration for MLB-Z4001
Item
Description
Function
Status
1
LED (Green)
Power -LED
Turn on the power LED is On
2
LED (Green\Yellow)
TX\RX- LED
Data transfer-Green is On\receive-
Yellow is On
3
LED(Orange)
Link-LED
Ethernet link-Orange is On
Table 5: Interfaces and Indicators Description of MLB-Z4001

MLB-Z4001 Terminal User Manual 12 Rev 1.0
3.2 Radio Interface (Type SMA Connector Female) - RF Antenna
Figure 4: Antenna Connector for MLB-Z4001
The connection of the antenna or other equipment must be decoupled from DC voltage.
For optimum RF performance, the MLiS Terminal has to be connected to an external RF antenna
matched to 50ohms including other connecting cables across the operating frequency bands. Please
use a SMA Male connection for the terminal.
Choose suitable types of low attenuation coaxial cables if possible. In general, the ohm types RG174 or
RG58 50 can be used. Avoid excessive cable length of > 10 meter
Compatible RF antennas (PCB patched or Monopole type) are available for order, please refer to
accessories document.

MLB-Z4001 Terminal User Manual 13 Rev 1.0
4OPERATING MODES
4.1 Power on the Modem
The modem is usually fully operational within 60 seconds, after powering it up. Depending on the signal strength
of the network in the area, logging into a network may take longer and is outside the control of the modem.
4.2 Configuration Tool
The MLiS ZigBee Configuration Utility is used to configure MLB-Z1001 or MLB-Z4001. If the user
wants to configure MLB-Z4001, you can select it from the drop down menu.

MLB-Z4001 Terminal User Manual 14 Rev 1.0
It can be used to set Destination Address, Network ID, and AES Encryption method etc. Also
Send/Recv data for testing MLB-Z4001 even configure the remote MLB-Z1001 or MLB-Z4001 devices
which are in the same ‘Network ID’and ‘AES Encryption’if enabled (under Advanced Tab) via API
mode in the ZigBee network.
Step 1：Choose MLB-Z4001 from the drop down menu. Select the desired device in the list. The
default IP address of MLB-Z4001 is 192.168.0.3/24. Please set your laptop NIC’s IP address to be in the
same network subnet accordingly. Then click on “Connect”.
Please note that the chosen MLB-Z4001 must be on the ‘Server’mode for connection. If not, you can
double click on the device to go into the web console management. Please change the device from
‘Client’mode to ‘Server’mode so the Configuration Utility could further work.
If the user would like to directly connect to the specific device instead by the broadcast search. You
can click on the blank column so the Socket Setting Window would pop up. You can input the Remote
IP and its port for the connection.

MLB-Z4001 Terminal User Manual 15 Rev 1.0
Step 2: Under the “Basic”Tab, the user can define the device name which can be up to 20 ASCII
characters.

MLB-Z4001 Terminal User Manual 16 Rev 1.0
Device Name: The user can input the desired device name for identification.
Serial Number: The device serial name is displayed here.
Destination address: The user can choose two methods to transmit the data. One is to broadcast the
input data to all connected devices in the same ‘Network ID’group. The second one is to input the
specific serial number of MLB-Z1001 or MLB-Z4001 ZigBee device to find that device for the data
transmission. Both methods are under Transparent Mode. Click on Apply and then hit Confirm button
in the Message pop-up window.

MLB-Z4001 Terminal User Manual 17 Rev 1.0
Transparent Mode:
All the transmission data can propagate thru from End Devices to the Computer located in the control
center via ZigBee network without any data modification.

MLB-Z4001 Terminal User Manual 18 Rev 1.0
API Mode:
The user can configure the remote MLB-Z1001 or MLB-Z4001 devices which are in the same ‘Network
ID’and ‘AES Encryption’with key if enabled. Please note that once change to this mode, the original
data would be added with extra header for configuration purpose. Please remember to change back to
the “Transparent Mode”for the original data transmission which is operational.
Once hit the “Apply”button after select API mode, Remote Modules Tab will be displayed. Go on to hit
“Discover”button to find the MLB-Z1001 or MLB-Z4001 devices which are in the same ‘Network ID’
and ‘AES encryption’if enabled. Then Double Click on the selective device for further configuration
from the remote.

MLB-Z4001 Terminal User Manual 19 Rev 1.0

MLB-Z4001 Terminal User Manual 20 Rev 1.0
Ethernet Setting (Web Console Management)
The default log-in account is Username: admin | Password: admin
The Default IP address is 192.168.0.3/24