Mobile Create IMP-R01W User manual

Remark
Cover
IMP-R01W User Manual

Remark
Page 1
Name and Function of parts
[Top]
[Front]
[Bottom] USB port
SOS key
Headset port
Front camera
Receiver
Proxy sensor / Light sensor
LED indicator
Touch Screen
Navy key
Number key
Main Mic

Remark
Page 2
[Side] [Side]
[Back]
Volume key
PTT Key
Power key
SIM/micro SD
slot cover
Rear camera
Flash
Sub Mic
Speaker
External
terminals

Remark
Page 3
Setting
Insert SIM card
Insert the Nano-SIM card and use phone.
1.Open the SIM / microSD slot cover on the right side of your phone.
2.Using the SIM remover, slide it into the hole on the side of the phone and the SIM /
microSD Tray will come out.
3.Place the SIM and microSD card on the removed tray, and then push the tray until it clicks
into the phone slot.
4. Close the SIM / Micro slot cover.
WARNING: Ensure that the SIM / microSD slot cover is properly
sealed to maintain waterproof performance of the phone.

Remark
Page 4
Battery charging
1.Connect the 5-pin connector of the micro-USB cable to the USB
charger port on the bottom of the phone.
2. Plug the other end of the USB cable into the AC adapter and plug the
adaptor into the concert.
WARNING: Only use chargers approved by the device. Using an
incompatible charger or modifying the charger port may damage
the unit and void your warranty.
WARNING: Make sure that the 5-pin connector on the micro-USB
cable is connected correctly or charging is working properly.

Remark
Page 5
Using phone
►Press and hold the Power key until the screen turns on.
Power on / off
Power on
1.Press and hold the Power key until you see the phone option.
2.Select power off to power off phone.
Power off
Display on / off
Display on
►Press the front key and the power key to display the screen.
Display off
►To turn off the screen, press the Power key.
Calling
Calling with keypad
1.Press the number key on the home screen to run the dial pad.
2.Press the number key of the number you want to call.
3.To edit the entered number, press the cancel key.
4.To make a call, press the call key.

Remark
Page 6
Calling with the dial pad
1.Touch the dial icon on the Home screen.
2.On the dial pad, tap the number you want to call.
3.Press the call icon on the dial screen to make a call.
Receive calls
Receive calls on the keypad
1.On the answer calls screen, press the call key.
2.To end the call, press the end call key.
3.If you do not want ring tones, press the volume key.
Answer a call with the dial pad
1.On the call screen, tap the call icon.
2.Press the reject icon to stop receiving calls.

Remark
Page 7
Display setting
Add a widget to your home screen
1.Press and hold the home screen background.
2.Touch Widgets to find the widget you want to add.
3.Drag and drop the widget you want to add to the home screen you want to add.
Move icons on the Home screen
1.On the Home screen, touch and hold the icon you want to move.
2.Drag the icon you want to move to the desired area to set it.
Delete icon on home screen
1.Drag the icon you want to delete to the top of the screen and move it to "X" delete.
2.Release the hand when the color of the icon changes
Change wallpaper
1.Press and hold the home screen background.
2.Select Backdrop and select My Photos to search for the image you want to use.
3.Select the image you want to use, and then tap Set wallpaper.

Remark
Page 8
Product Warranty
This product is officially imported and sold by our company.
The guarantee quality is as follows.
■Customer Service Guide
Before using the product, please refer to this manual.
■Notification before using
If the internal battery is discharged during the initial operation, the unit may not be turned on.
This is not a product defect, please charge the AC adapter for more than 30 minutes and
turn on the power.
The LCD of your product may cause red, white, or other pixels to appear,
but this is inevitable and unfavorable in the LCD manufacturing process.
The operating time of the battery depends on the usage environment of the system,
and the battery is a consumable item and its usage time decreases over time.
If the usage time decreases rapidly, please use the service center after replacement.
The memory provided to the mobile phone is used for the OS capacity and the software
required to run the product, so the actual memory is smaller than the total memory.
Memory will vary depending on your environment and may vary depending on other usage
environments such as software updates.
■Warranty period guide
Warranty period refers to the period during which the manufacturer or the seller of the
product provides free repair service to the defective quality performance function that
occurs naturally under normal conditions.
■Product Warranty Period
The warranty period of the product is two years from the date of purchase.
The warranty period is based on the date of purchase. If the date of purchase can not be
confirmed, the warranty period shall be from the date of manufacture or one month
from the date of shipment.

Remark
Page 9
■Even under the warranty period, the following cases are not eligible for free service.
●User carelessness, negligence or carelessness
(Careless handling, dropping, shock, breakage, flooding, unreasonable operation, etc.)
●The structure, performance, and function of the product may be changed by us or
by a person other than the technician modified, modulated or arbitrarily disassembled
●Replacement of consumable parts that have degraded performance due to normal use
●Failure of the product due to natural disasters (fire, salt, earthquake, flood, lightning, etc.)
●Fault due to power supply failure or faulty connecting device
●Faults that do not fulfill the precautions in the manual
●Inadequate use / storage environment (such as high temperature and humidity,
storage in an enclosed vehicle in summer, etc.) failure during use
●If the user breaks down due to arbitrary manipulation (such as routing) of
software and hardware
●If a malfunction occurs with consumables or accessories not specified by us
●If a malfunction occurs by installing or using an application that is not guaranteed by us
■Precautions for repair request
In the event of a product malfunction, the software and data installed by the user must be backed
up after the backup. We are not responsible for any changes or deletions to the software and data
that occur during the repair process, and the product may be in an initial condition when the repair
is complete. You must remove hardware, software, features, parts, options, options, and other
attachments that were not attached to or installed with the product at the time of purchase.
If you do not do so, we will not be responsible for any loss or damage.
Damage due to accessories not included in the product, surface damage, damage caused by
external shocks, damage caused by software or data, or use of removable storage media is not
guaranteed.

Remark
Page 10
This warranty does not apply when there is an error in operation resulting from the use of this
product in connection with a third party product, accessory or ancillary equipment, or when we
determine that the product itself is free from defects.
■Customer service center
●Homepage :
●Tel :
●Email :
■Precautions
●(When new / device is changed) Reboot 2-3 times with USIM installed.

Remark
FCC RF EXPOSURE INFORMATION:
WARNING!! Read this information before using your device
In August 1986 the Federal Communications Commission (FCC) of
the United States with its action in Report and Outer FCC 96-326
adopted an updated safety standard for human exposure to radio
frequency (RF) electromagnetic energy emitted by FCC regulated
transmitters. Those guidelines are consistent with the safety standard
previously set by both U.S. and international standards bodies. The
design of this device complies with the FCC guidelines and these
international standards. Use only the supplied or an approved
antenna. Unauthorized antennas modifications, or attachments could
impair call quality, damage the device, or result in violation of FCC
regulations. Do not use the device with a damaged antenna. If a
damaged antenna comes into contact with the skin, a minor burn may
result. Please contact your local dealer for replacement antenna.
Page 11

Remark
BODY-WORN OPERATION:
This device was tested for typical body-worn operations with the
back/front of the device kept 1cm from the body. To comply with FCC RF
exposure requirements, a minimum separation distance of 1cm must be
maintained between the user's body and the back/front of the device,
including the antenna,. Third-party belt-clips, holsters and similar
accessories containing metallic components shall not be used. At the
time of equipment certification there is body-worn accessory available in the
market supporting a separation distance of 1 cm which must be used in Hot Spot
and Body worn operation.
For more information about RF exposure, please visit the FCC website
at www.fcc.gov
Your Rugged IP PTT is a low power radio transmitter and receiver. When
it is ON, it receives and also sends out radio frequency (RF) signals. In
August, 1996, the Federal Communications Commissions (FCC)
adopted RF exposure guidelines with safety levels for hand-held wireless
devices. Those guidelines are consistent with the safety standards
previously set by both U.S. and international standards bodies:
<ANSIC95.1> (1992) / <NCRP Report 86> (1986) / <ICNIRP> (1999)
Page 12

Remark
Those standards were based on comprehensive and periodic evaluations
of the relevant scientific literature. For example, over 120 scientists,
engineers, and physicians from universities, government health agencies,
and industry reviewed the available body of research to develop the ANSI
Standard (C95.1). Nevertheless, we recommend that you use a hands-
free kit with your device (such as an earpiece or headset) to avoid
potential exposure to RF energy. The design of your device complies with
the FCC guidelines (and those standards).
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage the
device and may violate FCC regulations.
Page 13

Remark
RF Exposure Information:
This product is compliance to FCC RF Exposure requirements and refers
to FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm
search for FCC ID: 2AR6HIMP-R01W to gain further information include
SAR Values.
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Page 14

Remark
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Page 15

Remark
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Do not use the device with the environment which below minimum -10℃
or over maximum 50℃, the device may not work.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device is acting as host and operating in the 2.4 GHz (2412 ~2462
MHz) band. Ad Hoc function is supported but not able to operate on non-
US frequencies.
Page 16