Mobilita M606MG Installation guide

www.mobilita.in
TollFree : 1800 121 8485
Mobilita Wheelchair
Front
CODE M606MG , M606MC, M606MO , M606MW

Product Description
Weight Capacity : 100 Kg
01
Back Upholstery
Armrest Pad
Armrest
Side Panel
Seat Upholstery
Rigging
Footplate Caster ForkCaster Front
Brakes
Cap Hub Rear Wheel
Hand Grip
Rear Wheel
Mobilita wheelchairs are a product of quality
engineering and are manufactured to meet our
own highly rigid specifications and will surpass all
your expectations.
Please read this manual carefully to ensure safe
usage and understanding of maintenance
instructions.

02
EVERYDAY USE
CUSTOM ADJUSTMENTS *
To open chair - Open wheelchair by tilting to
one side and pushing down on seat rail until
fully opened.
To Close / Fold Chair - First fold foot plates to
vertical position. Grab seat with both hands at
front and back edge and lift. Or, tilt chair to
one side and lift up on seat rail.
Flip up Arms – Flip up arms by depressing
release spring button and lifting arms out of
front socket.
Adjusting length of Footrest / Leg rest - When
adjusting length of foot rests or leg rests, user
should be sitting in wheelchair with feet on the
foot plates. Loosen bolt on the clamp around
support assembly. Raise or lower foot plate to
desired position that will provide maximum
support of thighs. Front rigging should not be so
low that it causes uncomfortable pressure to
thighs at front of seat upholstery. Footrest should
not be lower than 2-1/2” from the ground to
ensure clearance.
Adjusting / Elevating Leg rest - Lift foot plate on
leg rest assembly to desired position. Release leg
rest assembly and it will automatically lock into
place. To lower, push out on leg rest lever and
lower foot plate to desired position.
Please read this manual carefully to ensure safe
usage and understanding of maintenance
instructions.

03
PERIODIC INSPECTION & CARE
Wheels - Large rear wheels should be inspected
at least once a month to ensure proper tightness.
Check for wheel wobble or looseness.
General Care - Wipe chrome parts with a clean,
soft cloth at least once a week. All metal parts can
be cleaned with auto wax or similar products. If
exposed to moisture, dry immediately. Do not use
an abrasive cleanser that will scratch the finish.
USE & SAFETY
Wheel Locks - Engage both wheel locks before
getting in or out of chair, leaning forward in chair,
or while in an elevator or wheelchair lift. Locks are
engaged by pushing handle completely forward.
Adjustments to locks are made by loosening or
tightening nut on the carriage bolt. Tighten nut
and bolt to secure in position. Test for correct
locking action before actual use.
Tyres - Solid tyres need minimal maintenance,
but should be cleaned occasionally with a damp
cloth. Replace if tyres become severely worn or
cracking appears.
Front Castors - Castors should be checked
periodically and lubricated occasionally.
Removal of Swing away Foot Rests / Leg Rests -
Release lock by pushing on the front rigging lever.
Swing-away foot rest /leg rest out and sideways.
Lift to remove.

04
CAUTION
Do not attempt to adjust or operate wheelchair
without reading carefully all instructions in this
manual.
This wheelchair is not suitable to be used as a seat
that can be used within vehicles of any kind.
Always transfer wheelchair user to a vehicle man-
ufacturers approved seat and use safety restraints
available.
Do not operate this wheelchair on roadways,
streets or any surfaces with vehicular trac.
Do not attempt to operate on inclines 10% or
greater without proper assistance.
Be sure to completely engage wheel locks when
getting in and out of wheelchair or when in eleva-
tor or wheelchair lift.
Wheelchair should be on a smooth, stable and
level area with wheel locks engaged before trans-
ferring user in or out of wheelchair.
When getting in or out of wheelchair, do not
stand on or apply weight to foot rests.
Before reaching or leaning forward, rotate castors
to front of the wheelchair engage wheel locks to
help prevent wheelchair from tipping over.
Do not lean over or apply weight to the top of
wheelchair back. This can cause wheelchair to tip
over. When trying to extend arms over back, only
reach as far as your arm can extend without
having to alter your seating position.

05
DO NOT stand on wheelchair.
DO NOT use wheel locks to slow your descent
down an incline.
Abruptly changing directions while going down
an incline could cause instability or possible
tipping over.
Stability - Wheelchair is designed to be safe and
stable as long as center of gravity is maintained
while going about normal activities. Care must be
taken while performing activities that shift your
center of gravity in the chair. Never reach so far
that require you to shift in the seat or bend over
out of the chair.
Ramps - Be sure of your own capabilities, limita-
tions and strength before attempting to go up a
ramp. Correct techniques on ramp negotiation
should be shown to you by a qualified profession-
al. Assistance is recommended when going up or
down inclines greater than 10 degree. Avoid
changing direction when going down an incline,
as this could result in instability of tipping over.
*Applicable for certain wheelchair models

Warranty
Your Mobilita branded product carries a limited warranty
to be free from defects in material and workmanship.
Applicable to the original purchaser only.
This device is built to exacting standards and
carefully inspected prior to shipment. This Warranty is an
expression of our confidence in the materials and
workmanship of our products and our assurance to the
consumer of years of dependable service.
This warranty does not cover device failure due to owner
misuse or negligence, or normal wear and tear. The
warranty does not extend to non-durable components,
such as rubber accessories, casters, and grips, which are
subject to normal wear and need periodic replacement.
If you have a question about your Mobilita device or this
warranty, please contact an authorized Mobilita dealer.
© 2018 Eternity Distribution Pvt. Ltd. All rights reserved
Mobilita is a trademark of
Eternity Distribution Pvt. Ltd.
Chennai, Tamil Nadu, India | Made in China for Mobilita
[email protected] | TollFree 1800 121 8485

www.mobilita.in
TollFree : 1800 121 8485