MOBILUS COSMO | HB Lite User manual

MOBILUS MOTOR Spółka z o.o.
ul. Miętowa 37, 61-680 Poznań, PL
tel. [phone], fax [phone]
VAT NO. PL9721078008
www.mobilus.pl
User manual of
COSMO |HB Lite controller.
Wersja 1.0ENG, 201104

1. GENERAL INFORMATION
COSMO | HB lite is a 15-channel remote control, designed for remote control receivers brand
MOBILUS (radio remote controls for roller shutters, awnings, blinds / control modules for
motors without radio communication module / ON / OFF modules)
• Support 15 channels.
• Support 15 channel groups.
• One-way radio communication.
Remote COSMO | HB Lite - is a remote control with touch screen keyboard with additional
beeps.
Please refer to the instruction manual that tells how to safely use the device. You are solely
responsible for any damages resulting from the using the device in a manner inconsistent
with its intended purpose. The manufacturer accepts no responsibility for damage or injury
caused by misuse, improper handling and running.
2. DESCRIPTION OF THE REMOTE CONTROL
2
1
COSMO | HB lite
1Display - channels / status.
2 Ring of 4 information LED’s.
3 Flap housing.
4 Battery compartment 2 x AAA.
P1 Programming button 1.
P2 Programming button 2.
Control button / navigation area LEFT.
Control button / navigation area RIGHT.
Control button / navigation area UP.
Control button / navigation area DOWN.
Control button / navigation area STOP.

CONTINUED 2. DESCRIPTION OF THE REMOTE CONTROL
P2
3
P1
4
3. CONTENTS OF THE PACKAGE
The packaging contains the following items:
• remote COSMO | HM or COSMO | HB
• 2 AAA batteries in the remote control protected against discharging with a seal,
• user manual,
• wall holder with magnet and fixing pins (2 pcs.).
4. TECHNICAL PARAMETERS
• Radio protocol: COSMO / COSMO | 2WAY READY (the remote control does not support
two-way communication transmission - it does not receive feedback messages, it
ensures sending commands to receivers)
• Frequency: 868 [MHz]
• Dynamic code
• FSK modulation
• The supply voltage 3,0 V DC .
• Power source: batteries 2 x AAA LR03.
• Working temperature [ oC ]: 0-40oC.
• Display: LED segment.
• Range in building: 40 [m]. The range of the radio signal depends on the type of con-
struction, used materials and placement of units. The transmition of the radio signal in
different conditions is as follows: brick wall 60-90%, reinforced concrete 2,060%, wooden
structures with sheets of plasterboard 80-95%, glass 80-90%, metal walls 0-10%.
• Buzzer - tone generator – only the remote COSMO | HB
• Dimensions of the remote control (without the handle): 49 x 16 x 125 mm.

5. POWER SUPPLY
The device is powered by two batteries AAA LR03. In the case of low battery level the display shows
information Lo. To change the battery slide the bottom flap down tight.
+ -
6. THE INITIAL COMMISSIONING
The device is factory protected against battery
wearing. To the deprotecion:
1. Open the battery cover.
2. Remove the seal Z, which protects the
batteries from discharging (marked
in white).
Z
7. READING OF REMOTE INTO THE MOTOR’S MEMORY
WARNING! Do not program the remote control when the shutter is in the extreme position
(top or bottom). Each program and changes of motor’s operation directions are confirmed by
two micro-movements of the driver.
Failure to comply with these rules may result in damage the blinds (inhaled by the housing).
1. Press the / to select the appropria-
te channel. Select the desired channel 1
to 15 with the buttoms. - FIg. 7.1.
Fig. 7.1
2. Enter MOBILUS motor, serie R in the PROGRAMMING MODE OF MASTER REMOTE:
- press for 5 seconds PROGRAMMING BUTTON in the motor - Fig. 7.2a;
- or double turn off and turn on the power supply od the motor - Fig. 7.2b;
The confirmation of properly performed operation will be two micro-movements of the
motor drive - FIg. 7.2c;.

CONTINUED 7. READING OF REMOTE INTO THE MOTOR’S MEMORY
Fig. 7.2
ON OFFON OFF
2x
a b c
5 s.
WARNING! The first remote control readed into the receiver is a remote control MASTER.
It allows you to operate motor and enter it in the PROGRAM MODE OF OTHER REMOTES.
3. On the remote control simultaneously press the P1- Fig. 7.3a.4 LEDs start blinking - Fig.
7.3b. Hold the button until the motor driver will perform two micro-movements. The
remote control has been readed into the motor.
Fig. 7.3a
P2P1
Fig. 7.3b
8. READING IN OTHER REMOTE
1. On the MASTER remote control press the P1 - Fig. 8.1a. 4 LEDs start blinking - Fig. 8.1b.
Hold the button until the motor driver will perform one micro-movement confirming
the input of the motor in the PROGRAM MODE.
Fig. 8.1a
MASTERPILOT 2 MASTER MASTER
P2P1
Fig. 8.1b
MASTERPILOT 2 MASTER MASTER
2. On the second remote control, you want
to program, press the
and - Fig. 8.2c. or for another
COSMO | HB lite - press the programming
button P1. Hold the button until the motor
driver will perform on micro-movement -
Fig. 8.2d. Another remote was loaded into
the motor.
FIg. 8.2c
MASTERPILOT 2 MASTER MASTER
Fig. 8.2d
a b c
4 s.
Within 20 sec. you can proceed to load the next remote. However, if no action of programming at this
time doesn’t happen, motor automatically returns to the OPERATING MODE. You can expedite return
to the OPERATING MODE manually using the remote control MASTER. In this case, press the button
P1 and hold more than 5 seconds. In both cases, return to the OPERATING MODE will be confirmed
by two micro-movements of the driver.

9. CHANGE OF MOTOR’S OPERATION DIRECTION
a cb
P2P1
WARNING ! You can change the direction of the work of motor for MOBILUS drives with
electronic limit switches only before setting the upper and lower limit switches. You can change
the direction of work for the MOBILUS motors with mechanical limit switches at any time.
After loading the remote control to the motor check that the buttons UP and DOWN correspond
to lifting and lowering the blinds. If not, press buttons P2 and hold them for about 4 seconds on
the remote control any loaded to the motor. The confirmation of correctly performed operation
are micro-movements of the driver.
10. TRANSMISSION PROTOCOL SWITCHING COSMO - COSMO | 2WAY
Remote control COSMO | HB Lite works in latest version of radio communication COSMO | 2WAY
ready. If you need to change the mode to an older version (for example, if you purchase a new
remote control for older COSMO radio tubular motors), follow these instructions:
1. Activate the remote control with the / buttons.
2. Press and hold the P1 + P2 function buttons on the back of the controller for 20 seconds at the
same time - Fig. 10.
3. When the LEDs at the bottom of the front panel light up, the corresponding communication
standard is activated:
colour red - the latest radio communication COSMO | 2WAY READY
blue colour- previous communication COSMO
Fig. 10
P2P1
> 20 s.
11. CHECK THE ACTIVE COMMUNICATION MODE
To quickly identify the active communication mode:
1. Activate the remote control with the / buttons.
2. Press and hold the STOP button for about 5 seconds - Fig. 11.
3. The LEDs in the lower part of the front panel shall light up indicating:
colour red - the latest radio communication COSMO | 2WAY READY
blue colour- previous communication COSMO
Fig.11
> 5 s.

NOTES

WARRANTY
The manufacturer guarantees correct device functioning. The manufacturer also agree to repair or
replace device damaged if the damage results from defects in materials and construction.
The warranty is valid for 24 months from the date of purchase under the following conditions:
• Installation was made by a person authorized in accordance with the manufacturer’s
instructions.
• Seals haven’t been breached and unauthorized design changes haven’t been made.
• The device was operated as intended by the user manual.
• Damage is not a result of the improperly performed electrical installation or any atmospheric
phenomena.
• The manufacturer is not responsible for damage resulting from misuse or mechanical
damage.
• In case of failure the device should be provided for repair with proof of purchase.
Defects found during the warranty period will be removed free for no longer than 14 working days
from the date of acceptance of device for repair. The manufacturer MOBILUS MOTOR Sp. z o.o.
carries on warranty repairs repairs. If you have any questions, please contact your dealer (please
provide the following information: event description, description of the error, the conditions under
which the accident occurred).
MAINTENANCE
1. For cleaning, use a soft cloth (eg. microfiber), moistened with water. Then wipe dry.
2. Do not use chemicals.
3. Avoid using in soiled and dusty environments.
4. Do not use the device at temperatures higher or lower than the declared range.
5. Do not open the device - otherwise the warranty shall be lost.
6. The device is sensitive to dropping, throwing.
ENVIRONMENTAL PROTECTION
This appliance is marked according to the European Directive on Waste Electrical and Electronic
Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of
correctly, you will help to prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate wa- ste handling of this
product. The symbol on the product, or the documents accompanying the product, indicates
that this appliance may not be treated as household waste. It shall be handed over to the ap-
plicable collection point for the waste electrical and electronic equipment for recycling purpose.
For more information about recycling of this product, please contact your local authorities, your
household waste disposal service or the shop where you purchased the product.