MOBILUS COSMO User manual

User manual of
COSMO | WT controller.
www.mobilus.pl

1. GENERAL INFORMATION
COSMO | WT is a 1-channel remote controller for wall mounting, designed for remote
control receivers brand MOBILUS (radio remote controls for roller shutters, awnings, blinds /
control modules for motors without radio communication module / ON / OFF modules).
• Support 1 channel.
• Support 1 channel group.
• Bi-directional communication - the opportunity to receive additional feedback information
from receivers.
Remote COSMO | WT - a remote control with touch screen keyboard. It has the ability to
control with the motions.
2. DESCRIPTION OF THE REMOTE CONTROL
1
5
1 The touch screen of remote control
COSMO | WT.
2 Battery compartment 2 x AAA.
3 The upper, main housing of remote
COSMO | WT.
4 The rear housing flap mounted to the wall.
Control button / navigation area - UP.
Control button / navigation area - DOWN.
Control button / navigation area - STOP.
P1 Function button 1.
P2 Function button 2.
2

CONTINUED 2. DESCRIPTION OF THE REMOTE CONTROL
4
P2
2
3P1
3. CONTENTS OF THE PACKAGE
The packaging contains the following items:
• remote COSMO | WT,
• 4 AAA batteries in the remote control protected against discharging with a seal,
• user manual,
• fixing pins (2 pcs.).
4. TECHNICAL PARAMETERS
• Radio protocol: COSMO
• Frequency: 868 [MHz]
• Dynamic code
• FSK modulation
• The supply voltage 3,0 V DC .
• Power source: batteries 4 x AAA LR03.
• Working temperature [ oC ]: 0-40oC.
• Display: touch screen with illuminated fields.
• Range in building: 40 [m]. The range of the radio signal depends on the type of con-
struction, used materials and placement of units. The transmition of the radio signal in
different conditions is as follows: brick wall 60-90%, reinforced concrete 2,060%, wooden
structures with sheets of plasterboard 80-95%, glass 80-90%, metal walls 0-10%.
• Buzzer - tone generator.
• Dimensions: 80 x 80 x 20 mm.
3

5. ASSEMBLY OF A HOLDING FIXTURE
Elements of wall handle:
• rear housing of remote - A,
• anchors with screws - B.
1. Determine the position where the rear flap
of housing will be located (easy access, no
running power cables, pipes, reinforcement
of walls, etc.).
2. Determine the points on the wall so that the
rear housing after assembly will adhere to
the wall and will be mounted perpendicular
to the ground.
A
B
3. Drill the holes and place the assembly anchors
(distance between the holes 36 mm, diameter 3.5 mm).
4. Attach the handle and tighten it to the wall.
5. Place front housing of the remote control to screwed flip.
6. POWER SUPPLY
The device is powered by four batteries
AAA LR003.
In order to change the battery, disconnect the
upper housing remote from parts mounted
on the wall.
-- --
7. THE INITIAL COMMISSIONING
The device is factory protected against battery
wearing. To the deprotecion:
1. Open the battery cover
2. Remove the seal Z, which protects the
batteries from discharging (marked
in white).
Z
4

8. WT REMOTE CONTROL OPERATION | MOTIONS
Remote control COSMO | WT allows the user two control modes.
Mode 1 - touch - the user issue commands by touching with his finger on the remote’s screen.
Waking up the remote control followed by touching the screen of remote control.
Mode 2 touch with full support for motions - you wake up the remote through both by waving
your hand to the screen of remote control (a distance of about 10 cm) and by the touch. You
issue commands by touching the screen with your finger on the screen of remote control and the
corresponding movement of the hand in front of remote control.
To select a mode, press the P2 button located under the battery cover - Fig. 8a. Activation of
thenext mode is confirmed by lighting up of all control LEDs:
Mode 1 - light up control keys on red - Fig. 8b.
Mode 2 - light up control keys on blue - Fig. 8c.
Fig. 8
P2
a b c
1. In order to control the channel, activate the screen by waving your hand at a distance of
10 cm. The screen will be activated. White color is highlighted in the upper left corner. Wake up
by touching the surface of the remote sends an order to the receiver corresponding to the field.
2. Command ON / UP - you need to make a
movement with your hand from the bot-
tom up in front of the motor. The display
lights up control field on blue color .
WARNING! The return movement
of the hand should be performed
outside the remote control. Otherwise,
the command OFF / DOWN will be
activated.
5

CONTINUED 8. WT REMOTE CONTROL OPERATION | MOTIONS
3. Command OFF / DOWN - you need to
make a movement with your hand in the
direction from up to down in front of the
motor. The display lights up the control
field on blue color .
WARNING! The return movement of
the hand should be performed outside
the remote control. Otherwise, the
command ON / UP will be activated.
4. STOP command - you need to make a
movement with your hand from left to
right in front of the remote control (or vice
versa). The display lights up control field
on blue color .
9. WT REMOTE CONTROL OPERATION | ACTIVATING THE DISPLAY
Remote control COSMO | WT in order to save energy introduces a screen in stand-by mode.
Its re-activation can be done in two ways:
1. Activation by touching the finger in the control buttons field. The pilot will send to the receiver
an order corresponding to the area on the screen- Fig. 9.2.
Fig. 9.2
a b c
2. Activation by waving your hand to the field on the remote control screen. This mode is only
possible with the active control the motions. In this mode, the LED on the screen lights up in
the upper left corner of the screen.The remote control is expected to order for these channels or
select more channels - Fig. 9.3.
6

CONTINUED 9. WT REMOTE CONTROL OPERATION | ACTIVATING THE DISPLAY
Fig. 9.3
a
1 s.
b
10. READING OF REMOTE INTO THE MOTOR’S MEMORY
WARNING! Do not program the remote control when the shutter is in the extreme position
(top or bottom). Each program and changes of motor’s operation directions are confirmed by
two micro-movements of the driver. Failure to comply with these rules may result in damage
the blinds (inhaled by the housing).
WARNING! Operation: LOADING THE REMOTE CONTROL INTO MOTOR’S MEMORY is only
possible in the MODE 1 of remote control (motions control is off).
1. Enter MOBILUS motor, serie R in the PROGRAMMING MODE OF MASTER REMOTE:
- press for 5 seconds PROGRAMMING BUTTON in the motor - Fig. 10.2a;
- or double turn off and turn on the power supply od the motor - Fig. 10.2b;
The confirmation of properly performed operation will be two micro-movements of the motor drive - Fig. 10.2c.
Fig. 10.2
ON OFFON OFF
2x
a b c
5 s.
7

CONTINUED 10. READING OF REMOTE INTO THE MOTOR’S MEMORY
WARNING! The first remote control readed into the receiver is a remote control MASTER.
It allows you to operate motor and enter it in the PROGRAM MODE OF OTHER REMOTES.
3. On the remote control simultaneously press and - Fig. 10.3a.The LED’s will flash (two
upper rows) - Fig. 10.3b. Hold the buttons until the motor driver will perform two micro-mo-
vements. The remote control has been readed into the motor.
Fig. 10.3
a
b
2 s.
a
b
2 s.
a b c
4 s.
11. READING IN OTHER REMOTE
WARNING! Operation: READING THE NEXT REMOTE CONTROL is only possible in the MODE 1
of remote control (motions control is off).
1. On the MASTER remote control simultaneously press the and - Fig. 11.1a. The
LED’s will flash (two upper rows). Hold the buttons until the motor driver will perform
two micro-movements confirming the input of the motor in the PROGRAM MODE
- Fig. 11.1b.
Fig. 11.1
ab
MASTER MASTER
a b c
4 s.
Fig. 11.2
MASTER
PILOT 2
MASTER MASTER
a b c
4 s.
2. On the second remote control, you want to program, press the and . Hold the
buttons until the motor driver will perform two micro-movements - Fig. 11.2. Another
remote was loaded into the motor.
8

CONTINUED 11. READING IN OTHER REMOTE
Within 20 sec. you can proceed to load the next remote. However, if no action of programming at this
time doesn’t happen, motor automatically returns to the OPERATING MODE. You can expedite return
to the OPERATING MODE manually using the remote control MASTER. In this case, press the button
on the and and hold more than 5 seconds. In both cases, return to the OPERATING MODE will
be confirmed by two micro-movements of the driver.
12. CHANGE OF MOTOR’S OPERATION DIRECTION
a b c
4 s.
After loading the remote control to the motor check that the buttons UP and DOWN
correspond to lifting and lowering the blinds. If not, press simultaneously buttons STOP and
DOWN and hold them for about 4 seconds on the remote control any loaded to the motor. The
confirmation of correctly performed operation are two micro-movements of the driver.
WARNING ! You can change the direction of the work of motor for MOBILUS drives with electronic
limit switches only before setting the upper and lower limit switches. You can change the direction
of work for the MOBILUS motors with mechanical limit switches at any time.
WARNING! Operation: CHANGING THE DIRECTION OF MOTOR’s OPERATION is only possible
in the remote control MODE 1 (control motions are off).
13. BI-DIRECTIONAL COMMUNICATION
Remote control COSMO | WT enables bi-directional exchange of information with the receiver
/ receivers (sends and receive messages). This feature allows you to control the state of blinds,
check whether they have been properly lowered or raised as to whether there is damage to be
checked (eg. due to interference by third parties).
Correct functioning of bidirectional communication requires:
- use of the receivers with bidirectional communication,
- programming one channel only for one receiver,
- the correct channel configuration - setting for bidirectional communication channel,
- ensure seamless communication of the remote control with the receiver.
9

CONTINUED 13. BI-DIRECTIONAL COMMUNICATION
Receivers supporting the bidirectional communication: MOBILUS: M35 ERS, M45 ERS.
In the case where the performed operation remote COSMO | WT
receives from the receiver the error message (eg. the casing lock) red
LEDs in the lower row will light up. Due to the battery consumption
time of waiting for feedback has been limited to 20 seconds.
3 s.
a b
14. TRANSMISSION PROTOCOL SWITCHING COSMO - COSMO | 2WAY
Remote control COSMO | WT works in latest version of radio communication COSMO | 2WAY.
If you need to change the mode to an older version (for example, if you purchase a new remote
control for older COSMO radio tubular motors), follow these instructions:
1. Activate the remote control.
2. Press and hold the P1 + P2 function buttons on the back of the controller for 20 seconds at the
same time. - Fig. 14.
3. When the LEDs at the bottom of the front panel light up, the corresponding communication
standard is activated:
colour red - the latest radio communication COSMO | 2WAY
blue colour - previous communication COSMO
Fig. 14
P2P1
> 20 s.
15. CHECK THE ACTIVE COMMUNICATION MODE
To quickly identify the active communication mode:
1. Activate the remote control.
2. Press and hold the STOP button for about 5 seconds - Fig. 15.
3. The LEDs in the lower part of the front panel shall light up indicating:
colour red - the latest radio communication COSMO | 2WAY
blue colour - previous communication COSMO
10