Mobridge Bluetooth Gateway User manual

Bluetooth Gateway for Audi
User Manual

2010 Fiberdyne Systems Pty Ltd
Welcome
Congratulations on purchasing a mObridge
Bluetooth Gateway for your Audi. The mObridge
Bluetooth Gateway allows for full hands-free
phone control using the existing radio and
steering wheel controls in your Audi vehicle.

This booklet contains important information and warnings
on using your mObridge Bluetooth kit in your Audi.
The booklet is designed to t into your Audi User Manual
folder. We recommend adding this booklet to your Audi User
Manual folder for further reference.
Some illustrations may vary from your vehicle. You should
therefore regard illustrations as a general guide.
Refer to the separate mObridge Bluetooth for Audi:
Installation document for the installation instructions.
An alphabetical index can be found at the end of the guide.
About this Manual

Contents
Getting Started 04
Supported Equipment 04
Features 04
Steering wheel controls 05
Head-Unit Control 06
Base Model Radios 06
Pairing your Bluetooth Phone 06
Connecting & Disconnecting the Phone 07
Operation: Combi-instrument Display 08
Menu Structure 08
Making a phone call from the phonebook 09
Dialing a telephone number 09
Accepting an incoming call 09
Ending a telephone call 09
Accessing Call Lists 10
Changing System Settings 11
Operation: Head Unit 12
Making a phone call from the phonebook 12
Dialing a telephone number 12
Accepting an incoming call 13
Ending a telephone call 13
Sending DTMF tones 13
Call Lists 14
Software Updates 15
Troubleshooting 15
Warranty 15
Index 16

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
GETTING STARTED
04
Supported Equipment
The mObridge Bluetooth kit supports
the following equipment:
RNS-E
BNS 5.0
Chorus II+, Chorus III
Concert II+, Concert III
Symphony II+, Symphony III
Features
Hands free functionality
Dial Numbers
Access your phone book
Answer and Reject Incoming Calls
On-board DSP (digital signal processor)
for advanced noise-free audio.
Getting Started

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
GETTING STARTED 05
NOTES Steering wheel controls and vehicle display may differ between Audi models. This may slightly
change the operation of the mObridge Bluetooth kit between vehicles.
The mObridge Bluetooth kit can be controlled via the steering wheel controls in your vehicle.
An example of the steering wheel controls is found in the diagram below. Your controls may
differ slightly from shown, but the basic operation will remain the same.
Steering Wheel Controls
Applies to vehicles: with steering wheel controls.
6/,5-%
-/$%"544/.
0RESSINGTHE;-/$%=
BUTTONWILLCYCLEBETWEEN
THEAVAILABLEMENUSON
THECLUSTERDISPLAYAND
CANBEUSEDTOSELECTTHE
4ELEPHONE-ENU
6/,5-%
"Y USING THEVOLUME
;6/,5-%=SCROLLWHEEL
ONTHERIGHTHANDSIDE
ITISPOSSIBLETOCHANGE
THEVOICEVOLUMEDURING
ACALL
,%&4(!.$3#2/,,
5SING THE ,EFT ;3#2/,,=
WHEELWILLSCROLLBETWEEN
THEAVAILABLEMENUOPTIONS
!LONGPRESSON
;3#2/,,=DROPSBACK
TOTHEPREVIOUSMENU
3TEERING7HEEL"UTTONS &)'
-/$%
3#2/,,7(%%,

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
PAIRING YOUR BLUETOOTH PHONE
06
Pairing your Bluetooth Phone
Applies to vehicles: All
To pair your Bluetooth phone with the
mObridge Bluetooth kit, you will need to
do the following:
01 Turn ignition on.
02 Using the Bluetooth features of your
phone, perform a search for new devices.
03 Your Bluetooth phone should nd a device
named “CAR BT”. Connect to this device.
04 When prompted for a passkey, enter 1234
which is the default passkey.
05 Your phone should now connect to
the mObridge kit where it can then be
accessed using the steering wheel or
the radio controls.
NOTES
Please consult your phone’s user manual if you
have trouble searching for the mObridge device
from your phone.
A maximum of 5 Bluetooth devices can be paired
with the mObridge system at any time. To pair
an additional device, one or more of the existing
pairings will need to be deleted from the mObridge,
or the factory settings of the mObridge need to
be restored.
For some phones, you must manually allow the
phonebook synchronization to occur, by pressing
“OK” on the phone.
Head-Unit Control
Applies to vehicles: with RNS-E, BNS 5.0,
Concert III, Symphony III
It is also possible to control the telephone
operation using the head unit. Only head
units featuring a telephone mode provide
this functionality.
Base Model Radios
Applies to vehicles: without telephone controls
on the head-unit
Audi base-model radios (i.e. those without
telephone controls) are not capable of
controlling the telephone. In this case the
telephone must be operated only using the
steering wheel controls and cluster display.

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
PAIRING YOUR BLUETOOTH PHONE 07
Connecting a Phone
Now that the phone has been paired to
the system, it will connect and disconnect
automatically when ignition is turned on/off.
When the key is inserted and ignition is on,
mObridge will begin searching for all paired
devices, beginning with the most recent one
connected. It will do this until a connection
has been made. When ignition is switched
off and the key is removed, mObridge will
disconnect from any connected phone. If a
call is ongoing at this time it will transfer to
private mode on the handset.
NOTES
Some phones do not support automatic
connection – for these phones you will need to
manually connect to mObridge using the controls
on your phone.
Automatic Connection & Disconnection
When no phone is connected to the system,
this will be indicated on both the MFD and
also the head-unit (if head-unit features
telephone controls).
When a phone is connected, the current
phone name, signal strength, and network
name will be sent to your vehicle, provided
the phone supports this.
,ATERMODE
VEHICLE
&)'
km
16 16.1
D +19.0°c
IZaZe]dcZ
CdiZ
Telephone not
End
connected or
attached.
#LUSTER$ISPLAY
0HONENOT
CONNECTED
&)'
`b
]
D
E
CD
E=DC:

VOperation: Combi-instrument Display
Applies to vehicles: with DIS display
'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: COMBI-INSTRUMENT DISPLAY
08
Menu Structure
Applies to vehicles: All – except A4(B8), A5, Q5
Main Menu
The following menus are available in the Telephone menu on the combi-instrument.
When a phone is connected the entire menu is available.
Phonebook See page 08
Dialed List See page 10
Received Calls See page 10
Missed Calls See page 10
Settings Menu See page 11
When no phone is connected, only the Settings Menu is available.
4ELEPHONE-ENUS &)'
E
E=DC:
7DD@
&$&
!(,$+9
'&&ac
B
E
9>6A:9
A>HI
&$&
!(,$+9
'&&ac
B
E
G:8:>K:9
86AAH
&$&
!(,$+9
'&&ac
B
E
B>HH:9
86AAH
&$&
!(,$+9
'&&ac
B
E
H:II>C<H
B:CJ
&$&
!(,$+9
'&&ac
B
NOTE
In A4(B8), A5, Q5 vehicles, the DIS telephone display
is controlled by your radio. Please refer to your
vehicle documentation for the menu structure
in these vehicles. For instructions on changing
telephone settings in these vehicles, please refer
to the Installation guide.

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: COMBI-INSTRUMENT DISPLAY
09
It is possible to dial a number from the phonebook of the connected phone using the
steering wheel buttons.
Making a Telephone Call From the Phonebook
Applies to vehicles: All
NOTES
Your Bluetooth phone must support phonebook
sync to use this feature.
It may take a few minutes for your phonebook
to be available after connecting your phone,
depending on the size of your phonebook.
01 Enter Telephone Menu on the DIS using
the [MODE] button on the steering wheel.
02 Using the scroll wheel, select Phone Book.
The names from your phonebook menu
will be displayed on the cluster.
03 Press the Scroll Wheel to select the
phonebook entry you wish to dial.
04 If there are more than 1 phone numbers
associated with this entry, select the
number use wish to dial using the Scroll
Wheel and buttons.
05 On selecting the number to dial, the your
phone will begin dialling the number.
TIPS
If you have a large phonebook, you can scroll
through it quickly by icking the Scroll Wheel
quickly This will skip through the phonebook
by rst letter.
The system will synchronize up to 1000 entries
from your phonebook. Each entry can have 4
phone numbers assigned to it.
An incoming call will cause the radio to mute
and a ring tone to be audible. An incoming
call display will be displayed.
An incoming call can be accepted by pressing
the scroll wheel on the steering wheel.
Accepting an incoming call
using the steering wheel
Applies to vehicles: All
An active call can be ended using the scroll
wheel on the steering wheel.
Ending a telephone call
using the steering wheel
Applies to vehicles: All

Accessing Call Lists Using the Steering Wheel
Applies to vehicles: All
'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: COMBI-INSTRUMENT DISPLAY
10
mObridge will synchronize the Last Dialled, Missed, and Answered Call lists with your phone.
If a number is known from your phonebook, then the caller name will be displayed in
addition to the number.
Dialing a number from a Call List using the
steering wheel controls
01 Enter Telephone Menu on the DIS using the
[MODE] button on the steering wheel.
02 Using the [SCROLL] button scroll down
to Last Dialed, Missed Calls, or Answered
Calls options, and press the [SCROLL]
button to select.
03 Use the [SCROLL] button to select an
number, and press it to dial.
NOTES
Not all phones support the synchronization of
call lists over Bluetooth. For phones that do not
support this feature, only calls made while the
phone is connected to the vehicle will be contained
in the call lists.

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: COMBI-INSTRUMENT DISPLAY
11
Changing System Settings Using the Steering Wheel
Applies to vehicles: All – except A4(B8), A5, Q5
It is possible to change some of the system
settings of the mObridge system. Settings
are available in the System->Settings menu
on the MFD.
The settings can be changed even when no
phone is connected.
It is also possible to use the “mObridge
Wizard” to change the system settings
over a USB or Bluetooth connection. Please
consult the install manual for details.
NOTE
In A4(B8), A5, Q5 vehicles, the DIS telephone display
is controlled by your radio, and the mObridge-
specic settings menus are not available. Language
Settings on these vehicles are determined from the
vehicle. For instructions on changing telephone
settings in these vehicles, please refer to the
vehicle hand book.
System Settings Options
Telephone Volume 01 - 15
Volume level during a call.
Ring Volume 01 - 15
Volume level of ringing.
Prompt Volume. 01 - 15
Volume level of prompt beeps.
A2DP Streaming Volume 01 - 63
Volume level of A2DP
streaming for ring tones
Microphone Gain 01 - 15
Controls the volume of
the microphone audio
from the mObridge.
Language English
Sets the operating German
language. French
Spanish
Italian
Dutch
Factory Reset
Resets settings back to system defaults, and
deletes all Bluetooth pairings.

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: HEAD UNIT
12
VOperation: Head Unit
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
Making a telephone call from the phonebook
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
01 Select the phonebook menu.
02 Select the phonebook entry and number
you wish to dial
NOTES
Your Bluetooth phone must support phonebook
sync to use this feature.
It may take a few minutes for your phonebook
to be available after connecting your phone,
depending on the size of your phonebook.
0HONEBOOK-ENU &)'
Memory
End call Dial
Telephone - Mobiles
Telephone
John - 0419188647
Phone Book
Kim - 0419188647
Melissa - 0419188647
Tony - 0419188647
11:33
Dialing a telephone number
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
01 Using the control knob, enter the
telephone number you wish to dial.
02 Use the dial button to dial it.
$IAL.UMBER &)'
Memory
End call Dial
Telephone - Mobiles
Number
0418977369
0
1
2
3
45678
9
#
•
•
11:33
1

Accepting/Rejecting an Incoming Call
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: HEAD UNIT
13
Select Answer to answer the call.
Select Reject to reject the call to voice mail.
!NSWER2EJECT#ALL &)'
Memory
End call Dial
Telephone - Mobiles
Telephone
John
0419376599
Dialling
11:33
Phone Book
Ending a telephone call
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
Press the End call button.
Sending DTMF tones
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
While in a phone call, DTMF tones can be
sent using number select wheel.
3ENDING$4-&TONES &)'
Memory
End call Dial
Telephone - Mobiles
Number
0
1
2
3
45678
9
#
•
•
11:33
0

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
OPERATION: HEAD UNIT
14
Call Lists
Applies to vehicles: with RNS-E, BNS 5.0, Concert III, Symphony III
01 Enter the phonebook menu, and select
the call list you wish to view.
02 In the call list, select the number to dial it.
NOTES
Not all phones support the synchronization of
call lists over Bluetooth. For phones that do not
support this feature, only calls made while the
phone is connected to the vehicle will be contained
in the call lists.
Call Lists may take several minutes to synchronize
with the phone.
#ALL,ISTS &)'
Memory
End call 0417128642 Dial
Telephone - Mobiles
Call List
John - 0413858637
Cameron - 0417128642
Kim - 0417348940
Melissa - 0412964385
Tony - 0415366698

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
SOFTWARE UPDATE 15
Unable to pair a device
You already have five devices paired to
mObridge. The system can only support
ve paired devices so you must delete an
existing device.
Phone book not appearing
Your Bluetooth phone does not support
phonebook sync.
It may take several minutes for your phone
book to sync, especially with very large
phone books.
Call lists not appearing or updating
Your phone does not support the
synchronization of phone lists.
SMS not appearing
Your Bluetooth phone does not support SMS.
SMS may take a minute or two to
synchronize with the phone.
Troubleshooting
Applies to vehicles: All
From time to time mObridge will release
software updates for mObridge Bluetooth
for Volkswagen. These software updates will
provide support for new Bluetooth phones
as well as adding support for new vehicles.
There is never any need to return the unit to
mObridge to update it.
This is important as it helps to future-proof
your investment.
Software updates can be performed in 2 ways:
01 If your mObridge has an SD-card slot
equipped, insert an SD-card with the
new software into the SD-card slot to
automatically update the device.
02 If your mObridge has a micro-USB
connector, connect the mObridge to a
PC with the mObridge Update Wizard
installed.
In either case, the latest software together
with update instructions are available on
our website. www.mobridgeinc.com
Software Update
Applies to vehicles: All
Warranty
Your mObridge audio interface is warranted against any manufacturing defects for a period of
12 months from purchase. Any part of the mObridge audio interface may be replaced or repaired
at the discretion of the manufacturer after such part is deemed to have a manufacturing fault.
If you have any questions about your mObridge audio interface, please contact your local
service agent, whose details are attached to the back page of this user instruction manual.

'%44).'34!24%$
",5%4//4(&/2!5$)-!.5!,
INDEX
16
Index
Answered Calls List 10, 14
Bluetooth Devices
Connecting 07
Deleting 11
Pairing 06
Unable to Pair 07
Call Lists 10, 14
Making a Telephone Call
via RNS-E, BNS 5.0, Concert III, Symphony III 12
Missed Calls List 10
Received Calls List 10
Steering Wheel Controls 05
Reorient or relocate the receiving antenna
Increase the separation between the
equipment and receiver
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/
TV technician for help
WARNING:
Any changes or modications not expressly
approved by mObridge, Inc. could void the user’s
authority to operate this equipment.
FCC information
Applies to US customers only
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference
in a residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interface
by one or more of the following measures:

www.mobridgeinc.com
ASIA-PACIFIC
Address 2/88 Northgate Drv Thomastown Melbourne VIC 3074
Phone [phone]
Inquiries [email protected]
NORTH AMERICA
Address 800 South Pacic Coast Highway
Suite 8 - #348 Redondo Beach California 90277
Phone [phone]
Inquiries [email protected]
EUROPE
Address Marconiweg 15 3899 BR, Zeewolde The Netherlands
Phone [phone]
Inquiries [email protected]