Saab 12 787 887 User manual

Saab 9-3 M03-
900 Installation instructions
SCdefault
MONTERINGSANVISNING ·INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG ·INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3 M03-
Parking assistance (SPA)
Accessories Part No. Group Date Instruction Part No. Replaces
12 787 887 9:40-03 Oct 02 12 788 454 12 788 454 Jul 02
F930A042

2 12 788 454
Saab 9-3 M03-
1 SPA control module
2 Holder (x4)
3Seal(x4)
4 Distance sensor (x4)
5 Moulding, bumper
6 Wiring harness, distance sensor
7 SPA wiring harness
8 Dust cover
9 Cable tie (x2)
F930A054
1
9
5
7
6
2
3
4
8

12 788 454 3
Saab 9-3 M03-
1 Disconnect the negative cable from the battery
and raise the vehicle.
2 Remove the two nuts holding the air shield of the
rear bumper against the body. Remove the two
screws holding the bumper shell against the
wheel housings.
3 Lower the vehicle and remove the rear bumper
trim moulding.
4 Open the hatchback.
F930A044
2
2 2
3

4 12 788 454
Saab 9-3 M03-
5 Lift up and fold aside the luggage compartment
floor and remove the luggage compartment
scuff plates.
6 Remove the hatches from the luggage compart-
ment side trims.
7 Remove the scuff plates from the side frames.
8 Remove the clip for the left-hand side trim and
move the trim aside.
9 Remove the rear lamp cluster.
F930A045
6
7
9
9
8
8

12 788 454 5
Saab 9-3 M03-
10 Remove the bumper shell screws that are locat-
ed below the rear lamp cluster.
11 Remove the bumper bolts at the wheel housings.
12 Remove the bumper shell by first pulling the
side pieces outwards and then pulling the bump-
er shell rearwards.
13 Remove the sound insulation from behind the
right-hand wheel housing.
Important
Place the bumper on a clean, soft surface.
F930A046
10
13
12
11

6 12 788 454
Saab 9-3 M03-
14 Remove the rubber plug from under the left-
hand rear light.
15 Remove the console in which such equipment
as a CD changer may be fitted. Disconnect the
connections to any equipment in the console.
16 Remove the rearmost connector (blue) from the
rear electrical centre. Make a note of how the
rear wiring harness is connected and then
remove it.
WARNING
The visible red light is a class 1 laser. Do not look
directly into the optical fibre or the control module
connector at close range. A distance of less than
20 mm between your eyes and the light source
may cause eye injury.
F930A047
16
16
16
16
16
16
16
16
14
16
16
16
16
16
16

12 788 454 7
Saab 9-3 M03-
17 Fit the new wiring harness.
Connect the wiring harness with reference to the
notes from the preceding point. Fit a new dust
cover and secure the harness components with
a cable tie.
Important
The harness attachment under the rear light should
not be fitted yet as the sound insulation uses the
same attachment.
F930A048
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17 17

8 12 788 454
Saab 9-3 M03-
18 Plug in the control module and fit it onto the
mounting point on the rear electrical centre.
19 Remove the support from the bumper shell.
F930A049
19
18

12 788 454 9
Saab 9-3 M03-
20 Fit the bumper-shell trim-moulding with the help
of the guide tabs and clip in the hooks, begin-
ning at the centre and working outwards.
21 Fit the seals to the sensors.
22 Fit together the distance sensors and the holders.
23 Fit the distance sensors to the mountings on the
trim moulding.
24 Connect the sensor wiring harness to the sen-
sors and fit it into the slots in the bumper shell.
25 Fit the support to the bumper shell.
Important
The connector sockets on the sensors should
point towards the right-hand side of the vehicle.
F930A050
21
22
23 25
24 24
24

10 12 788 454
Saab 9-3 M03-
26 Lift up the bumper shell and thread the wiring
harness through the hole under the left-hand
rear light. Fit the grommet.
27 Fit the two tabs of the bumper shell under the
holders and the outer corners between the
wheel arch liner and the holder at the wheel
housings. Press the bumper shell into place.
28 Plug in the parking assistance harness connec-
tor and fit the connector into the hole beside the
left-hand rear light. Fasten the wiring harness
with a cable tie.
29 Fit the bumper shell screws which are located
below the rear lamp cluster.
30 Fit and connect the rear lamp cluster. Check the
fit against the boot lid moulding.
WARNING
Check that the wiring harness is not pinched.
Incorrect fitting can damage the wiring harness
and cause a short-circuit/fire.
F930A051
30
30 30
27
27
28
26
F930A051
28