Mocet Communicator IP3092 Instruction manual

IP3092/IP3092L Communicator
Quick User Guide
Copyright © 2013, All Rights Reserved.
Ver: R12 D/C: 102-1216

Page 2
MOCET IP3092/IP3092L Communicator Quick User Guide
CE Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic compatibility, EN55022 class
B for ITE and EN 50082-1. This meets the essential protection requirements of the European Council
Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic
compatibility.
A & C Tick Declaration of Conformity
This equipment complies and passed tests preformed according to AS/NZS CISPR 22-2009 Class B at
Sporton International Inc. Lab. Certificate No. A1272301 and complies with AS/ACIP S004-2008 test
report No. 1022TEC_Mocet IP 3092_S004.
Environment
The phone you have purchased, as well as any used batteries must not be disposed of with household
waste. You should return these to your distributor if they are to replaced or dispose of them in an
approved recycling center.
Trademarks
iPad™, iPod™, iPhone™, iPad2™, the new iPad™, iTunes™, iOS™, Safari™, AirplayTM and Facetime™
are registered trademarks of Apple Inc., USA. All other company, brand and product names, like
Metaswitch™, Broadsoft™, Freeswitch™ and Asterisk™ are registered trademarks of their
respective owners.
WARNING! ▼
1. Read these installation instructions carefully before connecting the IP phone to its power
2. To reduce the risk of electric shock, do not remove the cover from the IP phone or attempt to
dismantle it. Opening or removing covers may expose you to dangerous voltage levels. Equally,
incorrect reassembly could cause electric shock on re-use of the appliance.
3. Do not expose the IP Phone to Fire, direct sunlight or excessive heat.
4. Do not expose the IP Phone to rain or moisture and do not allow it to come into contact with water.
5. Do not install the IP phone in an environment likely to present a THREAT OF IMPACT.
6. You may clean the IP phone using a fine damp cloth. Never use solvents (such as
trichloroethylene or acetone), which may damage the phone’s plastic surface and LCD screen.
Never spray the phone with any cleaning product whatsoever.
7. Take care not to scratch the LCD screen.
8. The IP phone is designed to work in temperatures from 5oC to 40oC.
9. The IP phone must be installed at least 1 meter from radio frequency equipment, such as TVs,
radios, hi-fi or video equipment (which radiate electromagnetic fields).
10. Do not connect the LAN/PC port to any network other than an Ethernet network.
11. Do not attempt to upgrade your IP phone in an unstable power environment. This could cause
unexpected issues.
12. Do not work on the system or connect or disconnect cables during lightning storms.
13. Children don't recognize the risks of electrical appliances. Therefore use or keep the phone only
under supervision of adults or out of the reach from children.
14. No repair can be performed by the end user, if you experience trouble with this equipment,
for repair or warranty information, please contact your supplier.
!

Page 3
MOCET IP3092/IP3092L Communicator Quick User Guide
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna
or transmitter.

Page 4
MOCET IP3092/IP3092L Communicator Quick User Guide
Introduction
The MOCET™ Communicator™ is an innovative accessory for the Apple™ iPad™ that will
enable you to use your iPad as your desk phone with popular APPs such as FaceTime™ and
Skype™. Different Communicator models are used for different iPad devices. IP3092
supporting Apple 30-pin connector is designed for iPad 1, iPad 2, and iPad 3, and IP3092L
supporting 8-pin lightning connector is designed for iPad 4.
Use the high definition audio-enabled handset and speakerphone on the Communicator to
enhance your communication and ensure privacy and comfort. For small office use, an external
desktop microphone can be attached improving your conference call experience. The enhanced
dynamic range stereo speakers make listening to music and watching movies a more engaging
experience.
The Communicator stand is adjustable between 30º and 75º, allowing you to find the most
convenient viewing angle for watching movies or participating in video conferences. The
Communicator can fast charge and power your iPad for all day work and play,and the USB port
can charge an additional iPhone or other mobile device.
A Bluetooth-enabled iPad / iPhone / Android Pad / mobile phone can be paired with the
Communicator allowing calls to be directed to the handset or speakerphone for improved call
quality and comfort.
Your Communicator supports many advanced functions, especially a powerful an embedded
VoIP engine. If you wish to use social media or business communication Apps such as
Skype, Facetime or Jabber etc., disregard the VoIP software installation section.
(1) One micro-SD and one USB host port on the IP3092/IP3092L allows user to connect
WiFi dongle, keyboard or other supported devices.
(2) Two 10/100 Ethernet ports on Communicator allow you to connect your computer as a
pass-through to your network, requiring only one Ethernet cable to your switch or router
for both.
(3) The IP Commander App downloaded from the Apple App Store can support the
operation and control of VoIP function which is embedded in the IP3092.
Hardware Installation
The Communicator comes with all the accessories needed to get going right away. Included
in the box are Quick Guide, the handset, handset cord, power supply adapter, and an
Ethernet cable. Please check on the Communicator and proceed the following sections of
this Quick Guide.
Set Up the Communicator:
- Unpacking the package box; place the Communicator on the table and turn its stand to a
proper angle (say 45 degree, please see Figure 1).
- Then connect the handset to the curly handset cord first and plug the other end of the cord
to the phone jack marked HAND on the rear panel of the Communicator. Please refer
to the Figure 2 and the back shell ports of the Communicator.

Page 5
MOCET IP3092/IP3092L Communicator Quick User Guide
Figure 1. To Set up the Communicator with a proper stand angle
[Remark]:
In the carton the hinge of IP3092 stand is set at 0o. To adjust the stand
position, open the hinge by pulling firmly out from the stand. The first
position of hinge is placed at 30o. Then you can adjust the stand angle
at any position from 30 o to 120 o , so that you can find the most
convenient viewing angle.
Connect the Power:
- Then plug the barrel plug of the included power adapter to the port marked 12VDC.
Make sure you use the right power adaptor with a label showing 12V and 2A.
- Then plug in the other end of power adaptor to an AC power outlet. The LEDs on the
Communicator will illuminate momentarily and then the Communicator will boot.
Figure 2. The Back Panel of the Communicator and How To Connect

Page 6
MOCET IP3092/IP3092L Communicator Quick User Guide
Booting Up :
The Communicator will take about two minutes to boot. When the Communicator is booting
up, the blue-green LED (MWI) indicator on the top of the unit will illuminate. Please don’t
insert the iPad into the Communicator untill the MWI LED is extinguished.
InsertingThe iPad:
-Except iPad 1, keep the add-on tray in the dock no matter IP3092 (for iPad 2 and iPad 3)
or IP3092L (for iPad 4). To dock the iPad 1, remove the add-on tray first. (see figure
below).
-By sliding your iPad into the front bezel slot will cause the battery signal showed on the
upper right corner of the iPad screen to be changed from to . Then the
Communicator is ready for operation.
[Remarks]:
There are some ports not necessary for general App users.
(1) Console port: this is reserved for engineering service only.
(2) PC and LAN Ethernet ports: are for embedded VoIP application only. If required
connect the IP3092 to Ethernet port via the CAT-5 cable that is supplied. To
eliminate the requirement for multiple Ethernet cables to a user’s location, the user’s
computer can be connected to the network through the second Ethernet PC port
on the Communicator
Appearance & Function Description
Before inserting the iPad to the Communicator, please check if you need the add-on tray for
your iPad device (iPad 2, iPad 3, or iPad 4). The figure below shows the Add-on Tray can be
removed or slid in easily. Users of the new thinner iPad Air or iPad Mini with model
IP3092L can use the second tray with your Communicator. (see details with tray)

Page 7
MOCET IP3092/IP3092L Communicator Quick User Guide
Figure 3. The Communicator Front Appearance and Add-on Trays
Communicator Keys
Name of Key Description
Speakerphone Press this key to enable or disable the Speakerphone; a blue
LED is used to indicate status
Mute Press this key to mute a call (the other party will not be able to
hear you when making a phone call by using communication
APP)
Headset Press this key to enable or disable the Headset feature.
Volume Rocker
Volume control keys to adjust volume of Handset Receiver,
Handset DTMF output, Handset Ring output, Headset
Receiver, Headset DTMF output, Headset Ring output,
Speakerphone output, Speakerphone DTMF output and
Speakerphone Ring output
The following 2 keys only relate to VoIP functions of the Communicator

Page 8
MOCET IP3092/IP3092L Communicator Quick User Guide
Hotline Press this key to make an emergency call no matter the iPad is
attached or not; requires subscription to a VoIP service provider
or connection to an IP PBX. A red LED is used to indicate its
status
Home Press this key to bring supported apps immediately to the
foreground. A blue LED is used to indicate its status
LEDs on The Communicator
LED Color Status Description
Off Communicator has booted OK.
Message Waiting
Indicator
Blue Steady The Communicator is booting or updating
Steady System is under upgrade or abnormal state.
Red
Blinking Network is disconnected
Steady Support HD audio quality
Handset
Blue Off HD audio quality not supported
Speakerphone
Blue Blue-green LED indicates that speakerphone is enabled
Mute Blue Blue-green LED indicates that Mute is enabled
Headset Blue Blue-green LED indicates that the headset feature is
enabled
Off Normal condition
Home Blue
Steady On N/A
The following LED only relates to VoIP functions of the Communicator
Hotline
Red N/A (Only supported in VoIP mode)
I/O Port Functions
The front, rear and side view of the Communicator with location of connectors is shown in the
following figures and the description of I/O ports is listed in the table here. Refer to their
locations in Figure 4 and 5.
NO. Port Description of I/O Port
1 iPad Docking Port Apple connector for iPad on the front shell
- IP3092: 30-pin connector
- IP3092L: 8-pin Lightning connector

Page 9
MOCET IP3092/IP3092L Communicator Quick User Guide
2 Handset Port RJ9 jack for attaching handset with curly phone cord
3 Microphone Input Port RJ9 jack to connect an external microphone pair for
hands free (conferencing) mode
4 Ethernet LAN Port RJ45 Ethernet port for VoIP applications
Note: This port is not necesary for App user.
5 Ethernet PC Port RJ45 Ethernet port for VoIP applications
Note: This port is not necesary for App user.
6 12VDC Power In 2.5mm Jack for external power adapter
7 Console Port 4-pin header for engineering service port
Note: This port is not necesary for general user.
8 Kensington Lock
Mount For user to lock the Communicator against theft
9 Micro SD Card Port For VoIP mode only which is used to store
Communicator firmware, configure file, voice mails,
melody, IVR greetings, etc.
Note: This port is not necesary for App user.
10 USB 2.0 Host Port This can be used for iPhone charging.
For VoIP mode only which is to support WiFi USB
dongle, USB Keyboard, or other devices.
11 WiFi AP Router Port Reserved for future WiFi accessory support
Note: This port is not necesary for App user.
12 Wiring Duct For inserting curly handset cord intoits slot
13 Headset Port 3.5mm jack for standard Apple ear buds or headset
Figure 4. The Apple 30-pin or Lightning Connector for Docking

Page 10
MOCET IP3092/IP3092L Communicator Quick User Guide
Figure 5. I/O Ports on Back Shell and Sides

Page 11
MOCET IP3092/IP3092L Communicator Quick User Guide
Software Installation
If you are not a VoIP user or want to use VoIP later, you can skip this section, there is no
need to install the Commander app. However, the system will always display a dialog box
for asking you to install the Commander app if you haven’t installed the app in your iPad.
To avoid this kind of disturbance from the system, we suggest you to install the Commander
app by following below procedures.
If you intend to use VoIP now, please refer to the separate “IP Commander for iOS VoIP
User Guide” booklet.
Installing The Commander App on Your iPad
When an iPad is inserted into the Communicator, the Communicator will scan the iPad to
determine whether it has been connected to the Communicator and whether it has the
Commander app installed previously. If this is the first time you have connected your iPad to
the Communicator, and you do not have the Commander app, a dialog box will
comment“This accessory requires an application you do not have” and “Would you like to
install it from App store?”
Please press the “Yes” button. Then the iPad will lead you to iTunes store to dowload the IP
Commander app. and you will be prompted to confirm the “install” on your iPad.
If more than one iPad shares one Communicator, the download and install process will be
repeated for each new iPad docked.
After successful installation, keep the IP Commander APP on your iPad. If you delete the IP
Commander APP, you need to do the download and install procedure again. If any upgrade is
notified, please update. This IP Commander App is mainly designed to let user to run VoIP
mode and operate the embedded VoIP functions. It does however, provide the way system
updates and provides new features that can be installed on your machine.

Page 12
MOCET IP3092/IP3092L Communicator Quick User Guide
Use Communicator To Play Music/Audio
To start using the Communicator for iPad APP. There are 2 paths supported for delivering
audio to theCommunicator, one by Apple connector (USB) or one by Blue tooth. The Apple
connector’s USB path is set as default.
Docking with an Apple Connector:
(1) Charging: When the Communicator powers on and is ready and the iPad is inserted
all the way into the Apple connector, the iPad will start charging. In addition, the user
can charge his/her iPhone or other mobile phone by connect it to the USB port on
the right side of the Communicator.
(2) Adjusting the Stand Angle for Playing Videos: The user can adjust the screen
angle by holding the stand and the base unit and opening or closing the stand to a
comfortable angle, ranging from 30 to 75 degrees (see the figure above).
(3) Playing Audio: By default audio from an docked iPad plays through Apple
connector onto the speakers, handset or headset of the Communicator.
Audio Path via Bluetooth:
The Communicator supports Bluetooth 2.1 EDR and the A2DP audio profile for a
wireless connection to the iPad’s audio system.
You can pair your iPad, iPhone or another mobile phone to the Communicator by using
the Bluetooth discovery process on your iPad, iPhone or another mobile phone to find
and associate it to the Communicator. You will see a device ID like IP3092-xxxxxxxxxxx
when finished scanning.
When the iPad, iPhone or other mobile phone is properly paired with the Communicator.
When connected, you can control the audio output of the iPad, iPhone or other mobile
phone using the volume controls on the Communicator to play music or make a call of
Facetime, Skype or other App using the Communicator’s handset, speakerphone and
headset.
When the Communicator is paired via Bluetooth, the music or audio will continue playing
even when the iPad/iPone/mobile phone is not connected to the Communicator.
When the iPad is docked successfully on the Communicator, the iPad will use the
Lightning 8-pin or 30-pin connector as it supports true wide-band quality for both music
and voice calls.
To Run iPad Apps
To Run Music Movie Player APP:
After plugging the iPad into the Communicator, you can direct the APP’s audio to the

Page 13
MOCET IP3092/IP3092L Communicator Quick User Guide
Speaker, Headset or Handset just by pressing the Speaker key, Headset key, or handset
off-hook.
To Run Social Networking APP
Many users like to run social networking and communications apps, like FacetimeTM,
SkypeTM,, Hookflash™ and other apps on their iPads. The Communicator’s high quality
audio system greatly enhances the user experience for voice and video calls. Your calls
will sound better, regardless of whether the app supports narrow-band or wide-band
audio. For comfort and convenience, the user can switch the audio among
speakerphone, handset or headset and volume can be adjusted independently for all
three modes.
To Pickup The APP Calls During Playing Music :
(1) When you are playing the music, you can go to the Social Networking APP’s screen
for standby. When an incoming call occurs, the App will wake up and play the ringtone
to Speaker.
(2) When you are playing music, but the Social Networks APP is on the background, the
incoming call will generate a notice to the iPad screen. The ringtone may not be
played if the APP is not well configured. But the music may be reduced or stopped
during the ringtone.
(3) When you encounter the above issue, please go to “Setting” APP of iPad and find that
social networking APP to set it correctly.
Note: To Run Special APP
(1) Some Apps may not support Bluetooth.
(2) Some APPs may not support audio through the Apple connector (USB audio).
In this case, you may need to switch the audio path to Bluetooth. Facetime is a case
that only Bluetooth audio is applicable for Handset mode with the Communicator.
(3) For other APPs, if you get any issue with the Audio play or endpoint (Speakerphone,
Headset, and Handset), you may have to try various settings.
More Information
If you are subscribed to a VoIP service from IP PBX or ISP/ITSP and utilise the VoIP function
of the Communicator, you may contact your administrator or supplier for configuration
assistance. Then refer to the separate IP Commander for iOS VoIP User Guide for more
information. Some IP providers and business/corporate enviroments will deploy an
Auto Configuration Services or wizards to set up your VoIP service.
Thank you for your choice of product. Remember to register your Communicator at first and
record down your Communicator product Serial Number (S/N) below for further support
service.

Page 14
MOCET IP3092/IP3092L Communicator Quick User Guide

 Notes 
This device has Model number, MAC Address and Serial Number which are located on
the back of Base Unit. Please record down them for service check.
Model Number: IP3092 MAC: SerialNumber:
And every time you change the PASSWORD and/or User ID, please record down and retain
them for use.
USERID: PASSWORD:
USERID: PASSWORD:
USERID: PASSWORD: