Fan Wi-Fi Reset
NOTE: This function only resets the Wi-Fi settings.
1. Press and hold the and buttons for 10 sec.
2. The LED will blink green and the receiver will beep to
indicate that Wi-Fi reset is successful.
3. After the Wi-Fi resets, the fan will broadcast its factory
set network name beginning with “ModernFormsFan.”
NOTE: Changes to your Wi-Fi network settings
(SSID or Security Passphrase) will prevent your fan from
connecting to the cloud. You can re-establish connectivity
by performing a Wi-Fi Reset and using the Modern Forms
app to recongure the fan to connect to the network with
the new settings.
5
Using Power Switch
This process can be used when it is inconvenient to use
one of the other processes.
NOTE: You must use a switch that cuts power to the fan
receiver for this process to work.
This will reset all fans connected to the switch being used.
1. Turn o power at power switch for 3 seconds.
2. Turn on power for 6 seconds. Turn o power.
3. Turn on power. In approximately 6 seconds the receiver
will beep. When the receiver beeps turn o power.
Repeat step 3 four additional times. On the fourth
repetition the fan will beep three times indicating the
fan has performed a factory reset.
NOTE: This will remove remote control(s), wall control(s)
and Modern Forms app connections.
Using Receiver Button
1. Power down the receiver and within
3 minutes of turning the power back on,
press and hold the reset button on the receiver
until the receiver beeps.
2. Power cycle the circuit to complete
the process.
NOTE: This will remove remote control(s), wall
control(s) and Modern Forms app connections. FIG.7
6
Factory Reset
Using remote control
Remote Control Factory Reset:
1. Press and hold the , and buttons
for 10 seconds.
2. The LED will blink green and the receiver will
beep
CAUTION: The user is cautioned that changes or modications
not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION: The cells shall be disposed of properly, including keeping
them away from children and even used cells may cause injury
FCC Supplier’s Declaration of Conformity
Brand name: Modern Forms
Model number: F-RCBT-WT
This device complies with part 15 of the FCC Rules. Operation is subject to
the
following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WAC LIGHTING CO.
44 Harbor Park Drive, Port Washington, NY 11050
Tel: 1-866-810-6615
Rules and Regulations
Unpairing
NOTE: Unpairing must be completed
within 3 minutes of turning the power
on to the fan receiver.
1. When you re-engage power to the
fans you want to unpair, press and
hold the and buttons
for 4 seconds.
2. The LED will blink green, and the
receiver will beep to indicate that
unpairing is successful.
4
FIG.5
FIG.6
Press and Hold
Press and Hold
“The bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Wangs Alliance
Corporation is under license. Other trademarks and trade names are those
of their respective owners.”
NOTE: This will remove remote control(s), wall
control(s)
WARNING: Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery. If a new or used
lithium button/coin cell battery is swallowed or enters the body, it can cause
severe internal burns and can lead to death in as little as 2 hours. Always
completely secure the battery compartment. If the battery compartment
does not close securely, stop using the product, remove the batteries, and
keep it away from children. If you think batteries might have been swallowed
or placed inside any part of the body, seek immediate medical attention.
