Modus Furniture DORSEY WOOD QUEEN BED User manual

BOX#1
A. HEADBOARD 1PC A
BOX#2
BOX#3 :
B
D
HARDWARE KITPACKEDIN BOX#2
18PCS
ALL-THREADBOLT
(5/16"x80mm)
2THREADED HALFMOON
WASHERNUT(5/16")
3SPANNER 1PC
WOODSCREW(4x30mm) 6PCS
00:30
ASSEMBLEONASOFTSURFACE
PAGE1OF8
No. DESCRIPTION IMAGE QUANTITY
FULLYASSEMBLED
8PCS
Not provided
1PC
ALLENKEY
B. FOOTBOARD 1PC
D.SLATROLL1SET
BED HARDWARE BOX
4
5
ALLEN BOLT(1/4"x50mm)
612PCS
LOCKWASHER(5/16")
FLATWASHER(1/4")
7
8
E
C
F
G
C.SIDERAIL2PCS
E. CENTER SLATSUPPORT1PC
F. MATTRESSSPACER 2PCS
G. SUPPORTLEG 4PCS
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS
12PCS
12PCS

PAGE2OF8
STEP #1:
A
STEP #2:
B
x4
x4
1
1
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS

C
STEP #4:
STEP #3:
PAGE3OF8
A
B
C
C
C
X8
2
X8
3
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS

PAGE4OF8
STEP #5:
STEP #6:
A
B
E
G
X4
E
G
E
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS
STOP
*IFUSINGBEDFRAME WITHADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX
A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT.
*IFUSINGBEDFRAME WITHSTANDARD BOXSPRINGORFOUNDATION
CONTINUE TOSTEP 5.

PAGE5OF8
STEP #7:
STEP #8:
D
X2
X4
4
4
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS

PAGE6OF8
STEP #9:
STEP #10:
F
F
6
7
8
5
x12
F
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS

PAGE7OF8
INSTRUCTIONSFORADJUSTINGLEVELER:
.POSITIONTHEBEDIN YOUR SPACEAND LOCATE
THELEVELERUNDEREACH SUPPORTLEG.
.TURN THELEVELERCOUNTER-CLOCKWISETOEXTEND
THELEVELERANDCLOCKWISETORETRACTIT.
.ADJUSTEACHLEVELERUNTIL EACH SUPPORTLEGISAPPLYING
EQUAL,UPWARD PRESSUREON THEBEDSUPPORTSLAT.
MAINTENANCEINSTRUCTION:
.REMOVEBOXSPRINGANDMATTRESSBEFOREMOVING
YOUR BED.
.LIFT YOUR BEDWHEN MOVINGIT.
DRAGGINGCANDAMAGETHELEGSUPPORT.
.READJUSTLEVELERSAFTERMOVINGYOUR BED.
ASSEMBLY COMPLETE.
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS

AN ADJUSTABLE MATTRESS BASE ISAFREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THEBED FRAME.
IFUSING THISBED FRAMEWITH ASTANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
PRE-ASSEMBLED SIDE RAILCLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOWTHESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLEMATTRESS BASE INSTALLATION:
PAGE8OF8
APPENDIXA: ADJUSTABLE MATTRESS BASEASSEMBLY SUPPLEMENT
STEP 1:
USE ALLEN KEY (5) INBOX #2 TO UNSCREWALLEN BOLTS AND REMOVE PRE-ASSEMBLED SIDE RAILCLEATS.
NOTE: YOU MAY WISH TO RETAINUNUSED PARTS IFINTHE FUTURE YOUINTEND TO USE THE BED FRAMEWITH
ASTANDARD BOX SPRING OR FOUNDATION
6. ALLEN BOLT (1/4x50MM) 12PCS
7. LOCK WASHER (5/16") 12PCS
8. FLAT WASHER (1/4") 12PCS
x12
DORSEY WOOD CALKING BED
ASSEMBLY INSTRUCTIONS
D.SLATROLL1SET
E. CENTER SLATSUPPORT1PC
F. MATTRESSSPACER 2PCS
G. SUPPORTLEG 4PCS
4.WOOD SCREW(4x30MM)6PCS