Modus Furniture MAXIME User manual

F U R N I T U R E
MAXIME FULL/QUEEN/E.KING BED
ASSEMBLY INSTRUCTIONS
UPDATED : JULY 25TH, 2023
STEP 1 :
NOT PROVIDED
0:30
YOUR BOX MAY CONTAIN
EXTRA HARDWARE
PART NO.
BOX 1 - HEADBOARD-FOOTBOARD BOX 2 - SIDERAILS
IMAGE DESCRIPTION QUANTITY
E SIDERAIL 2
PART NO. IMAGE DESCRIPTION QUANTITY
A HEADBOARD 1
B LEFT HEADBOARD LEG 1
1 ALLEN BOLT (6X35mm) 8
2 SPRING WASHER (M6) 8
3 FLAT WASHER (M6) 8
4 WOOD SCREW (8X30mm) 9
5 ALLEN BOLT (6X40mm) 11
6 ALLEN KEY 1
FULLY ASSEMBLED
F
CENTER SLAT
1
G LEG SUPPORT 4
PART NO.
BOX 3 - SLAT ROLL
IMAGE DESCRIPTION QUANTITY
H
SLAT ROLL
1
ASSEMBLE ON A SOFT SURFACE
D
FOOTBOARD
1
C RIGHT HEADBOARD LEG 1
HARDWARE KIT PACKED IN BOX 1
A
C
B
1
2
3
6
BACK VIEW
BACK VIEW
A
B
C
B
A
X8

STEP 2 :
F U R N I T U R E
STOP
· IF USING BED FRAME WITH ADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX A: ADJUSTABLE
MATTRESS BASE ASSEMBLY SUPPLEMENT.
· IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION CONTINUE TO STEP 5.
STEP 3 :
MAXIME FULL/QUEEN/E.KING BED
ASSEMBLY INSTRUCTIONS
UPDATED : JULY 25TH, 2023
STEP 4 :
E
DE
A
B
B
E
E
D
E
D
C
E
C
D
E

F U R N I T U R E
STEP 5 :
F
G
X4
6
5
F
G
G
F
T-NUT
5
6
STEP 8 : STEP 9 :
X2
X2 X1
HH
F
HH
GG
H
H
E
4
5
66
5
F
F
F
F
MAXIME FULL/QUEEN/E.KING BED
ASSEMBLY INSTRUCTIONS
UPDATED : JULY 25TH, 2023
STEP 6 : STEP 7 :
H
E
E

INSTRUCTIONS FOR ADJUSTING
LEVELER :
Position the bed in your space and locate the leveler
under each leg support ( G ).
Turn the leveler counter-clockwise to extend the
leveler and clockwise to retract it.
Adjust each leveler until each leg support is applying
equal, upward pressure on the center slat.
MAINTENANCE INSTRUCTIONS :
· Periodically check all fittings and tighten if
necessary, as they can loosen over time.
· Always remove box spring and mattress
before moving the bed.
· Lift the bed when moving it. Dragging the
bed can damage the center support.
· Readjust levelers after moving the bed.
F U R N I T U R E
STEP 10 :
STEP 12 :
ASSEMBLY COMPLETE
STEP 11 :
STEP 13 :
X6
X1 X2
G
HH
H
H
H
H
4
5
66
5
F
F
EE
E
MAXIME FULL/QUEEN/E.KING BED
ASSEMBLY INSTRUCTIONS
UPDATED : JULY 25TH, 2023

MAXIME FULL/QUEEN/E.KING BED
APPENDIX A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
F U R N I T U R E
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
F. CENTER SLAT 1PC
G. LEG SUPPORT 4PCS
H. SLAT ROLL 1SET
4. WOOD SCREW (8X30mm) 9PCS
5. ALLEN BOLT (6X40mm) 11PCS
STEP 1 :
USE ALLEN KEY (6) TO UNSCREW ALLEN BOLTS
AND REMOVE PRE-ASSEMBLED SIDE RAIL CLEATS.
X20
6
NOTE: YOU MAY WISH TO RETAIN UNUSED PARTS IF IN THE FUTURE YOU INTEND TO USE THE BED FRAME WITH
A STANDARD BOX SPRING OR FOUNDATION.
UPDATED : JULY 25TH, 2023