Modus Furniture LAWSON User manual

BOX #1
A. HEADBOARD (1PC) BOX #2
B. FOOTBOARD (1PC)
D.SLATROLL(1SET)
B
D
HARDWARE PACKED INBOX#2
18pcs
ALL-THREADBOLT
(5/16"x100mm)
2HALFMOONWASHER(5/16")
3HEXNUT(5/16")
4SPANNER 1pc
5WOODSCREW(4x30mm) 4pcs
00:30
ASSEMBLEONASOFTSURFACE
PAGE1OF7
BED HARDWARE BOX
No DESCRIPTION IMAGE QUANTITY
FULLY ASSEMBLED
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS
8pcs
8pcs
Not provided
6
1pc
ALLENKEY
BOX #3
C.SIDERAIL(2PCS)
E. CENTER SLATSUPPORT(1PC)
F.SUPPORTLEG (4PCS)
E
F
C
7
8
9
ALLEN BOLT(1/4"x40mm) 2pcs
2pcs
2pcs
LOCKWASHER(5/16")
FLATWASHER(1/4")
A

PAGE2OF7
STEP #1:
A
23
STEP #2:
STEP #3:
NOTE: HEX NUT(3)WILL BE FULLYTIGHTENED
WITH SPANNER (4) INSTEP 5.
C
B
A
C
A
1
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS
1

PAGE3OF7
C
STEP #5:
NOTE:AFTERINITIALLYHAND-TIGHTENINGTHEHEXNUTS (3),
THEY CAN ALLBEFULLYTIGHTENEDNOWUSINGTHESPANNER(4).
A
B
CA
32
C
STEP #4:
NOTE: HEX NUT(3)WILL BE FULLYTIGHTENED
WITH SPANNER (4) INSTEP 5.
4
CB
2
3
4
C
B
4
23
4
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS

PAGE4OF7
STOP
*IFUSINGBEDFRAME WITHADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX
A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT.
*IFUSINGBEDFRAME WITHSTANDARD BOXSPRINGORFOUNDATION
CONTINUE TOSTEP 6.
STEP #6:
E
Fleveler
E
F
STEP #7:
AB
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS

PAGE5OF7
STEP #8:
STEP #9:
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS
6
8
7
6
7
8
9
9

ASSEMBLY COMPLETE.
PAGE6OF7
STEP #10:
5D
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS
INSTRUCTIONSFORADJUSTINGLEVELER:
*POSITIONTHEBEDIN YOUR SPACEAND LOCATE
THELEVELER UNDER EACHSUPPORTLEG.
*TURNTHELEVELERCOUNTER-CLOCKWISE TO EXTEND
THELEVELER AND CLOCKWISETORETRACTIT.
*ADJUSTEACHLEVELERUNTIL EACH SUPPORTLEGISAPPLYING
EQUAL, UPWARDPRESSUREONTHEBEDSUPPORTSLAT.
MAINTENANCEINSTRUCTIONS:
*PERIODICALLYCHECKALLFITTINGSAND TIGHTEN IF
NECESSARY,ASTHEY CANLOOSEN OVERTIME.
*ALWAYSREMOVEBOXSPRINGANDMATTRESS BEFORE
MOVINGTHEBED.
LIFTTHEBEDWHEN MOVINGIT.DRAGGINGTHEBED CAN
DAMAGETHECENTERSUPPORT.
*READJUSTLEVELERSAFTERMOVINGTHEBED.

AN ADJUSTABLE MATTRESS BASE ISAFREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THEBED FRAME.
IFUSING THISBED FRAMEWITH ASTANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
PRE-ASSEMBLED SIDE RAILCLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOWTHESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
D. SLAT ROLL (1SET)
E. CENTER SLAT SUPPORT (1PC)
F. SUPPORT LEG(4PCS)
5. WOOD SCREW4x30mm (4PCS)
6. ALLEN BOLT 1/4"x40mm (2PCS)
7. LOCK WASHER 5/16"(2PCS)
8. FLAT WASHER 1/4"(2PCS)
9. ALLEN KEY (1PC)
PAGE7OF7
APPENDIXA: ADJUSTABLE MATTRESSBASE ASSEMBLYSUPPLEMENT
STEP 1:
USE ALLEN KEY (9) TO UNSCREWALLEN BOLTS AND REMOVE PRE-ASSEMBLED SIDE RAILCLEATS.
NOTE: YOU MAY WISH TO RETAINUNUSED PARTS IFINTHE FUTURE YOUINTEND TO USE THE BED FRAMEWITH
ASTANDARD BOX SPRING OR FOUNDATION
LAWSONQUEEN/KING BED
ASSEMBLYINSTRUCTIONS
9

BOX #1
A. HEADBOARD (1PC)
AB
D
HARDWARE PACKED INBOX#2
No Description Image Quantity
18pcs
2
3
4
ALLEN BOLT(1/4"x50mm)
514pcs
ALLENKEY
WOODSCREW(4x30mm)
16pcs
16pcs
1pc
4pcs
PAGE1OF8
6
7
8
9
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS
ALL-THREADBOLT
(5/16"x100mm)
HALFMOONWASHER(5/16")
HEXNUT(5/16")
SPANNER
8pcs
8pcs
1pc
FULLY ASSEMBLED
LOCKWASHER(5/16")
FLATWASHER(1/4")
BOX #2
B. FOOTBOARD (1PC)
D.SLATROLL(1SET)
BED HARDWARE BOX
BOX #3
C.SIDERAIL(2PCS)
E. CENTER SLATSUPPORT(1PC)
F. MATTRESSSPACER (2PCS)
G.SUPPORTLEG (4PCS)
C
E
G
F
10
ALLEN BOLT(1/4"x40mm) 2pcs
00:30
ASSEMBLEONASOFTSURFACE
Not provided

PAGE2OF8
STEP #1:
A
23
STEP #2:
C
B
AC
A
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS
1
1
STEP #3:
NOTE: HEX NUT(3)WILL BE FULLYTIGHTENED
WITH SPANNER (4) INSTEP 5.

PAGE3OF8
C
A
B
CA
32
C
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS
STEP #4:
NOTE: HEX NUT(3)WILL BE FULLYTIGHTENED
WITH SPANNER (4) INSTEP 5.
STEP #5:
NOTE:AFTERINITIALLYHAND-TIGHTENINGTHEHEXNUTS (3),
THEY CAN ALLBEFULLYTIGHTENEDNOWUSINGTHESPANNER(4).
CB
2
3
4
C
4
C
B
4
23
4

PAGE4OF8
STOP
*IFUSINGBEDFRAME WITHADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX
A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT.
*IFUSINGBEDFRAME WITHSTANDARD BOXSPRINGORFOUNDATION
CONTINUE TOSTEP 6.
STEP #6:
E
Gleveler
E
G
STEP #7:
AB
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS

PAGE5OF8
STEP #8:
STEP #9:
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS
6
8
7
6
7
8
9
9

STEP #11:
F
PAGE6OF8
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS
STEP #10:
10
D

PAGE7OF8
F
F
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS
5
7
8
9
F
7
8
5
9
x7
x7
STEP #12:
ASSEMBLY COMPLETE.
INSTRUCTIONSFORADJUSTINGLEVELER:
*POSITIONTHEBEDIN YOUR SPACEAND LOCATE
THELEVELER UNDER EACHSUPPORTLEG.
*TURNTHELEVELERCOUNTER-CLOCKWISE TO EXTEND
THELEVELER AND CLOCKWISETORETRACTIT.
*ADJUSTEACHLEVELERUNTIL EACH SUPPORTLEGISAPPLYING
EQUAL, UPWARDPRESSUREONTHEBEDSUPPORTSLAT.
MAINTENANCEINSTRUCTIONS:
*PERIODICALLYCHECKALLFITTINGSAND TIGHTEN IF
NECESSARY,ASTHEY CANLOOSEN OVERTIME.
*ALWAYSREMOVEBOXSPRINGANDMATTRESS BEFORE
MOVINGTHEBED.
LIFTTHEBEDWHEN MOVINGIT.DRAGGINGTHEBED CAN
DAMAGETHECENTERSUPPORT.
*READJUSTLEVELERSAFTERMOVINGTHEBED.

AN ADJUSTABLE MATTRESS BASE ISAFREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THEBED FRAME.
IFUSING THISBED FRAMEWITH ASTANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
PRE-ASSEMBLED SIDE RAILCLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOWTHESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
D. SLAT ROLL (1SET)
E. CENTER SLAT SUPPORT (1PC)
F. MATTRESS SPACER (2PCS)
G. SUPPORT LEG(4PCS)
PAGE8OF8
APPENDIXA: ADJUSTABLE MATTRESSBASE ASSEMBLYSUPPLEMENT
STEP 1:
USE ALLEN KEY (9) TO UNSCREWALLEN BOLTS AND REMOVE PRE-ASSEMBLED SIDE RAILCLEATS.
NOTE: YOU MAY WISH TO RETAINUNUSED PARTS IFINTHE FUTURE YOUINTEND TO USE THE BED FRAMEWITH
ASTANDARD BOX SPRING OR FOUNDATION
5. ALLEN BOLT 1/4"x50mm (14PCS)
6. ALLEN BOLT 1/4x40mm (2PCS)
7. LOCK WASHER 5/16"(16PCS)
8. FLAT WASHER 1/4"(16PCS)
9. ALLEN KEY (1PC)
10. WOOD SCREW4x30mm (4PCS)
9
LAWSONCALKING BED
ASSEMBLYINSTRUCTIONS