Modus Furniture GENEVA BED User manual

P8
P3 P4
P5 P6 P7
P9 P10
GENEVA BED ASSEMBLED
P1
P1. HEADBOARD 1 PC
P2. WOODEN LEG 2 PCS
P2
P3.FOOTBOARD 1 PC
P4.SIDE RAIL 2 PCS
P6.SLAT 26 PCS
P7.WOODEN LEG 2 PCS
P8.SIDE RAIL SLAT CLIP 26 PCS
P5.CENTER SLAT SUPPORT 1 PC
P9.CENTER SUPPORT SLAT CLIP 13 PCS
P10.CENTER SUPPORT LEG 2 PCS
HARDWARE* PACKED IN BOX #1
ALLEN KEY
5/16" PC PCS PCS PCS
A1 1444
BOLT FLAT
HARDWARE* PACKED IN BOX #2
PC PC PCS
B1 11 4 4
PCS PCS PCS PCS
416 12 4
5/16" 5/16"
5/16"*3.25" WASHER
LOCK
WASHER
BOLT
5/16"*1"
BOLT
5/16"*2.5"
BOLT
5/16"*3.25"
FLAT
WASHER
LOCK
WASHER
NUT
PCS
ALLEN KEY
A2 A3 A4
B2 B3 B4
B5 B6 B7 B8 5/16"
SPANNER
ALLEN KEY
1/4" PC PCS PCS PCS
A5 1888
BOLT FLAT
1/4"*1" WASHER
LOCK
WASHER
A6 A7 A8
ASSEMBLY INSTRUCTIONS
GENEVA BED
FULL/QUEEN SIZE
UPDATED : MAY 24TH, 2022

LOOSEN THE BOLTS OF HEADBOARD(P1) & FOOTBOARD(P3). CONNECT THE SIDERAIL(P4)
WITH HEADBOARD(P1) AND FOOTBOARD (P3) BY HOOK, TIGHTEN THE PRE-INSTALLED
BOLTS BY WRENCH(B1).
STEP 2 :
STEP 3 :
CONNECT THE METAL TUBE TO THE HEADBOARD & FOOTBOARD WITH BOLT(B3) BY
WRENCH(B1).ASSEMBLE THE SUPPORT LEG(P10) TO THE BOTTOM OF TUBE WITH
BOLT(B4) BY WRENCH(B1).
P1
P2
P2
A4
A2
A1
A3
STEP 1:
ASSEMBLE THE WOODEN LEGS TO THE BOTTOM OF HEADBOARD AND FOOTBOARD.
P4
B1
P1
P4 P3
P1
P4 P3
P5
P10
P1
P3
P7
B7
B5
B1
B6
P1
P3
B1
B3
B7
B6
P5
B1
B4 P5
B2
B7
B6 B6
B8
P10
STOP
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION, CONTINUE TO STEP 3.
IF USING BED WITH AN ADJUSTABLE MATTRESS BASE, SKIP STEPS 3,4& 5 AND
REFERENCE APPENDIX A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT.
UPDATED : MAY 24TH, 2022

INSERT CLIPS(P8) TO SIDE RAILS' TUBE.INSERT SLATS TO THE CLIPS(P8),THEN
CONNECT THE TWO SIDE'S OF THE SLATS TOGETHER BY CLIPS(P9).
STEP 4 :
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
TURN COUNTER-CLOCKWISE TO
EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH LEG
INSTRUCTIONS FOR ADJUSTING
LEVELERS :
MAINTENANCE INSTRUCTIONS :
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
CENTER SUPPORT.
READJUST LEVELERS AFTER MOVING
YOUR BED.
INSERT CLIPS(P9) INTO THE MIDDLE TUBE OF THE REMAINING SLATS TO THE BED
FOUNDATION.
STEP 5 :
SUPPORT LEG (P10).
SUPPORT IS APPLYING EQUAL UPWARD
PRESSURE ON THE CENTER SLAT.
P6 P5
P9
P6
P4
P8
P6
P5
P9
P6 P5
P1
P4 P3
P1
P4 P3
P6
P5
UPDATED : MAY 24TH, 2022

APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
USE A PHILLIPS HEAD SCREWDRIVER (NOT PROVIDED)
TO UNSCREW THE PHILLIPS SCREWS AND REMOVE THE
PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
WARNING!
SIDE RAIL CLEATS ARE HELD IN PLACE USING PHILLIPS HEAD SCREWS. ONCE THEY ARE REMOVED THE USER
WILL NOT BE ABLE TO SAFELY RE-INSTALL THE SIDE RAIL CLEATS FOR FUTURE USE WITH A STANDARD BOX
SPRING OR FOUNDATION.
P5. CENTER SLAT SUPPORT 1 PC
P6. SLAT 26 PCS
P8. SIDE RAIL SLAT CLIP 26 PCS
P9. CENTER SUPPORT SLAT CLIP 13 PCS
P10. CENTER SUPPORT LEG 2 PCS
ASSEMBLY INSTRUCTIONS
GENEVA BED
FULL/QUEEN SIZE
UPDATED : MAY 24TH, 2022

P8
P3 P4
P5 P6 P7
P9 P10
GENEVA BED ASSEMBLED
P1
P1. HEADBOARD 1 PC
P2. WOODEN LEG 2 PCS
P2
P3.FOOTBOARD 1 PC
P4.SIDE RAIL 2 PCS
P6.SLAT 39 PCS
P7.WOODEN LEG 2 PCS
P8.SIDE RAIL SLAT CLIP 26 PCS
P5.CENTER SLAT SUPPORT 2 PCS
P9.CENTER SUPPORT SLAT CLIP 26 PCS
P10.CENTER SUPPORT LEG 4 PCS
HARDWARE* PACKED IN BOX #1
ALLEN KEY
5/16" PC PCS PCS PCS
A1 1444
BOLT FLAT
HARDWARE* PACKED IN BOX #2
PC PC PCS
B1 1188
PCS PCS PCS PCS
428 20 8
5/16" 5/16"
5/16"*3.25" WASHER
LOCK
WASHER
BOLT
5/16"*1"
BOLT
5/16"*2.5"
BOLT
5/16"*3.25"
FLAT
WASHER
LOCK
WASHER
NUT
PCS
ALLEN KEY
A2 A3 A4
B2 B3 B4
B5 B6 B7 B8 5/16"
SPANNER
ALLEN KEY
1/4" PC PCS PCS PCS
A5 1888
BOLT FLAT
1/4"*1" WASHER
LOCK
WASHER
A6 A7 A8
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
GENEVA BED
UPDATED : MAY 24TH, 2022

LOOSEN THE BOLTS OF HEADBOARD(P1) & FOOTBOARD(P3). CONNECT THE SIDERAIL(P4)
WITH HEADBOARD(P1) AND FOOTBOARD (P3) BY HOOK, TIGHTEN THE PRE-INSTALLED
BOLTS BY WRENCH(B1).
STEP 2 :
STEP 3 :
CONNECT THE METAL TUBE TO THE HEADBOARD & FOOTBOARD WITH BOLT(B3) BY
WRENCH(B1).ASSEMBLE THE SUPPORT LEG(P10) TO THE BOTTOM OF TUBE WITH
BOLT(B4) BY WRENCH(B1).
P1
P2
P2
A4
A2
A1
A3
STEP 1:
ASSEMBLE THE WOODEN LEGS TO THE BOTTOM OF HEADBOARD AND FOOTBOARD.
P4
B1
P1
P4 P3
P3
P10
P1
P3
P7
B7
B5
B1
B6
P1
P3
B1
B3
B7
B6
P5
B1
B4 P5
B2
B7
B6 B6
B8
P10
P1
P4
P5
STOP
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION, CONTINUE TO STEP 3.
IF USING BED WITH AN ADJUSTABLE MATTRESS BASE, SKIP STEPS 3,4& 5 AND
REFERENCE APPENDIX A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT.
UPDATED : MAY 24TH, 2022

INSERT CLIPS(P8) TO SIDE RAILS' TUBE.INSERT SLATS TO THE CLIPS(P8),THEN
CONNECT THE TWO SIDE'S OF THE SLATS TOGETHER BY CLIPS(P9).
STEP 4 :
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
TURN COUNTER-CLOCKWISE TO
EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH LEG
INSTRUCTIONS FOR ADJUSTING
LEVELERS :
MAINTENANCE INSTRUCTIONS :
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
CENTER SUPPORT.
READJUST LEVELERS AFTER MOVING
YOUR BED.
INSERT CLIPS(P9) INTO THE MIDDLE TUBES OF THE REMAINING SLATS TO THE BED
FOUNDATION.
STEP 5 :
SUPPORT LEG (P10).
SUPPORT IS APPLYING EQUAL UPWARD
PRESSURE ON THE CENTER SLAT.
P6 P5
P9
P6
P4
P8
P9
P6 P5
P5
P6
P1
P4 P3
P5
P6
P1
P4
P3
UPDATED : MAY 24TH, 2022

APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
USE A PHILLIPS HEAD SCREWDRIVER (NOT PROVIDED)
TO UNSCREW THE PHILLIPS SCREWS AND REMOVE THE
PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
WARNING!
SIDE RAIL CLEATS ARE HELD IN PLACE USING PHILLIPS HEAD SCREWS. ONCE THEY ARE REMOVED THE USER
WILL NOT BE ABLE TO SAFELY RE-INSTALL THE SIDE RAIL CLEATS FOR FUTURE USE WITH A STANDARD BOX
SPRING OR FOUNDATION.
P5. CENTER SLAT SUPPORT 2 PCS
P6. SLAT 39 PCS
P8. SIDE RAIL SLAT CLIP 26 PCS
P9. CENTER SUPPORT SLAT CLIP 26 PCS
P10. CENTER SUPPORT LEG 4 PCS
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
GENEVA BED
UPDATED : MAY 24TH, 2022