Modus Furniture PARAGON 4N02L4 User manual

PARAGON FULL/QUEEN BED
TOOL REQUIRED : PHILLIPS HEAD
SCREWDRIVER (NOT PROVIDED)
0:30
YOUR BOX
MAY CONTAIN
EXTRA HARDWARE
PAN HEAD SCREW
(6x15mm)
WOOD SCREW
(8x30mm)
(6x40mm)
7
4
(6x35mm) (M6) (M6)
FLAT
E. SIDE RAIL 2 PCS
F. BED SLAT 3 PCS
G. SUPPORT LEG 3 PCS
BED HARDWARE BOX*
A. HEADBOARD PANEL 1 PC
B. LEFT HEADBOARD LEG 1 PC
C. RIGHT HEADBOARD LEG 1 PC
D. FOOTBOARD 1 PC
HEADBOARD HARDWARE BOX*
USE HEADBOARD HARDWARE PACKED IN BOX #1
FOR STEP 1.
USE BED HARDWARE PACKED IN BOX #2 FOR STEP 2
AND ALL REMAINING STEPS.
BED HARDWARE PACKED IN BOX #2
HEADBOARD HARDWARE PACKED IN BOX #1
UPDATED : JULY 1ST, 2020

3
4
F
G
IF USING BED FRAME WITH ADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX A: ADJUSTABLE
MATTRESS BASE ASSEMBLY SUPPLEMENT.
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION CONTINUE TO STEP 6.
STOP
F
G
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
SUPPORT LEG.
READJUST LEVELERS AFTER MOVING
YOUR BED.
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
SUPPORT LEG (G).
TURN LEVELERS COUNTER-CLOCKWISE
TO EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH
SUPPORT LEG IS APPLYING EQUAL
UPWARD PRESSURE ON THE BED SLAT.
INSTRUCTIONS FOR ADJUSTING
LEVELERS :
MAINTENANCE INSTRUCTIONS :
UPDATED : JULY 1ST, 2020

NOTE: YOU MAY WISH TO RETAIN UNUSED PARTS IF IN THE FUTURE YOU INTEND TO USE THE BED FRAME WITH
A STANDARD BOX SPRING OR FOUNDATION.
USE ALLEN KEY (3) TO UNSCREW ALLEN BOLTS
AND REMOVE PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
PARAGON FULL/QUEEN BED
F. BED SLAT 3 PCS
G. SUPPORT LEG 3 PCS
2. WOOD SCREW (8x30mm) 7 PCS
4. ALLEN BOLT (6x40mm) 4 PCS
3

PARAGON KING BED
E. SIDE RAIL 2 PCS
F. BED SLAT 3 PCS
G. SUPPORT LEG 6 PCS
BED HARDWARE BOX*
A. HEADBOARD PANEL 1 PC
B. LEFT HEADBOARD LEG 1 PC
C. RIGHT HEADBOARD LEG 1 PC
D. FOOTBOARD 1 PC
HEADBOARD HARDWARE BOX*
TOOL REQUIRED : PHILLIPS HEAD
SCREWDRIVER (NOT PROVIDED)
0:30
YOUR BOX
MAY CONTAIN
EXTRA HARDWARE
PAN HEAD SCREW
(6x15mm)
WOOD SCREW
(8x30mm)
(6x40mm)
7
7
(6x35mm) (M6) (M6)
FLAT
USE HEADBOARD HARDWARE PACKED IN BOX #1
FOR STEP 1.
USE BED HARDWARE PACKED IN BOX #2 FOR STEP 2
AND ALL REMAINING STEPS.
BED HARDWARE PACKED IN BOX #2
HEADBOARD HARDWARE PACKED IN BOX #1
UPDATED : JULY 1ST, 2020

IF USING BED FRAME WITH ADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX A: ADJUSTABLE
MATTRESS BASE ASSEMBLY SUPPLEMENT.
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION CONTINUE TO STEP 6.
STOP
F
G
3
4
F
G
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
SUPPORT LEG.
READJUST LEVELERS AFTER MOVING
YOUR BED.
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
SUPPORT LEG (G).
TURN LEVELERS COUNTER-CLOCKWISE
TO EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH
SUPPORT LEG IS APPLYING EQUAL
UPWARD PRESSURE ON THE BED SLAT.
INSTRUCTIONS FOR ADJUSTING
LEVELERS :
MAINTENANCE INSTRUCTIONS :
UPDATED : JULY 1ST, 2020

NOTE: YOU MAY WISH TO RETAIN UNUSED PARTS IF IN THE FUTURE YOU INTEND TO USE THE BED FRAME WITH
A STANDARD BOX SPRING OR FOUNDATION.
USE ALLEN KEY (3) TO UNSCREW ALLEN BOLTS
AND REMOVE PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
PARAGON KING BED
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
F. BED SLAT 3 PCS
G. SUPPORT LEG 6 PCS
2. WOOD SCREW (8x30mm) 7 PCS
4. ALLEN BOLT (6x40mm) 7 PCS
3
UPDATED : JULY 1ST, 2020