modway Bayport EEI-2699 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI-2699 COFFEE TABLE
Hardware:
Component:
1 Table Top x1
Thank you for purchasing the MODWAY COFFEE TABLE！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the coffee table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
1
4 Stretcher x2
2
A Short Bolt M6x30mm x 10
C Allen Wrench M4 x 1
B Long Bolt M6x70mm x 6
2
3
3
3
4
4
2 Side Frame x2 3 Support Rail x3

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI-2699 COFFEE TABLE
STEP 1:
Please put the Table Top (1) upside down on a carpeted or padded area.
Position 1 piece of Support Rail (3) into the bottom of Table Top (1) as shown.
Insert 2 pieces of Long Bolt (B) into the pre-drilled holes on bottom of Table Top (1) through the pre-drilled holes on Support Rail (3).
Repeat the same steps for the remaining Support Rails (3).
Use Allen Wrench (C) to tighten Long Bolts (B) clockwise until secure.
STEP 2:
1
Position 1 piece of Side Frame (2) to the assembled Table Top (1) and Support Rails (3) as shown.
Insert the tenon on assembled Support Rails (3) into the rabbet on the Side Frame (2).
Then position 2 pieces of Stretcher (4) to the assembled Table Top (1), Support Rails (3) and Side Frame (2) as shown.
Insert the tenon on assembled Stretchers (4) into the rabbet on the Side Frame (2).
3
Inside Label
Bx6 Cx1
B
3
3
C
B
B
B
B
B
2
3
3
3
4
4
1
Inside

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI-2699 COFFEE TABLE
STEP 3:
STEP 4:
Hardware & Tool required
Ax10 Cx1
Carefully position the other piece of Side Frame (2) to the assembled Table Top (1),Side Frame (2), Support Rails (3),
and Stretchers (4) as shown.
Insert the tenon on assembled Support Rails (3) and Stretchers (4) into the rabbet on the other Side Frame (2).
2
2
4
3
3
3
4
Insert 10 pieces of Short Bolt (A) into the pre-drilled holes on Support Rail (3) and Stretchers (4) through the pre-drilled
holes on Side Frames (2).
Use Allen Wrench (C) to tighten all Short Bolts (A) clockwise until secure.
2
2
3
3
3
4
4
1
A A
A
A
A
A A
A
A
A
C
1

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI-2699 COFFEE TABLE
STEP 5:
Assembly is complete. Your coffee table is ready to be used now!
Carefully turn over the assembled coffee table.