modway EEI –2046 User manual

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 1 of 2
EEI –2046 ROOM DIVIDER
Hardware:
Component:
A Long Bolt M8x435mm x6
G Allen Wrench x1
1 Top Panel x1 3 Side Panel x3
D Flat Washer x24
Thank you for purchasing the MODWAY ROOM DIVIDER！
！！
！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the room divider, we recommend that it is assembled by two adults, on
a carpeted or padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
2
1
2
2
3
5
3
5
3
5
4
5
2 Shelf x3
4 Bottom Divide Panel x1 5 Divide Frame x4
Wrench x1
Nut M8x8mm x8
F
E
B Short Bolt M8x395mm x2
C Bolt M8x35mm x14
H Cover x12
J Square Cover x4

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 2 of 2
EEI –2046 ROOM DIVIDER
STEP 1:
STEP 2:
Please put the Top Panel (1) upside down on a carpeted or padded surface.
Attach one piece of Divide Frame (5) into the bottom of Top Panel (1) by using 2 piece of Bolt (C) and 2 pieces of
Flat Washers (D) as shown.
Use Allen Wrench (G) to tighten the Bolts (C) clockwise until secure.
Insert 2 pieces of Long Bolt (A) into the bottom of Top Panel (A) by hand as shown.
Ax2 Cx2 Dx2 Gx1 Hardware & Tool required
Cx2 Dx4 Ex2 Fx1 Gx1 Hardware & Tool required
1
5
A C
G
A
C
5
D
Place 1 piece of Side Panel (3) to the bottom of Top Panel (1) through the 2 pieces of Long Bolt (A) as shown.
Attach 1 piece of Shelf (2) upside down to the Side Panel (3) and Divide Frame (5) by using 2 pieces of Nut (E) with
2 piece of Flat Washer (D) and 2 pieces of Bolt (C) with 2 pieces of Flat Washer (D) as shown.
Use Wrench (F) to tighten the Nuts (E) and Allen Wrench (G) to tighten the Bolts (C) clockwise until secure as shown.
1
3
2
5
2
3
F
E
D
G
C
D
D
C

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 3 of 2
EEI –2046 ROOM DIVIDER
STEP 3:
STEP 4:
Attach one piece of Divide Frame (5) into the bottom of Shelf (2) by using 2 piece of Bolt (C) and 2 pieces of
2pieces of Flat Washers (D) as shown.
Use Allen Wrench (G) to tighten the Bolts (C) clockwise until secure.
Insert 2 pieces of Long Bolt (A) into the bottom of Top Panel (A) by hand as shown.
Ax2 Cx2 Dx2 Gx1 Hardware & Tool required
Cx2 Dx4 Ex2 Fx1 Gx1 Hardware & Tool required
Repeat the same procedure as Step 2 for one pieces of Side Panel (3) and one piece of Divide Frame (5) as shown.
1
A
3
5
2
5
A
G
C
D
C
3 1
5
3
5
2
2
C
D
G E
E
D
F D
D
C

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 4 of 2
EEI –2046 ROOM DIVIDER
STEP 5:
STEP 6:
Repeat the same steps as Step 3 and Step 4 for one piece of Side Panel (3), one piece of Divide Frame (5) and one piece of
Shelf (2) as shown.
Ax2 Cx4 Dx6 Gx1 Ex2 Fx1 Hardware & Tool required
Hardware & Tool required
Repeat the same step as Step 3 for one pieces of Divide Frame (5) and 2 piece of Short Bolt (B) as shown.
1
1
3
2
3
5
2
5
3
2
Bx2 Cx2 Dx2 Gx1
B
B
3
2
2
2
3
3
5
5
5
C
D
G
C

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 5 of 2
EEI –2046 ROOM DIVIDER
Assembly is completed. The room divider is ready to enjoy now!
STEP 8:
Carefully turn over the room divider by two people.
Place the Bottom Panel (4) to the bottom of Shelf (2) through the Short Bolt (B) as shown.
Attach them by using 2 pieces of Flat Washer (6) and 2 pieces of Nut (E).
Use Wrench (F) to tighten the Nuts (E) clockwise until secure as shown.
Attach 12 pieces of Cover (H) to holes on bottom of the Shelves (2).
Attach 4 pieces of Square Cover (J) to the bottom of Divide Frame (5)
and Bottom Panel (4) as shown.
STEP 7:
Hardware & Tool required
2
2
2
3
3
3
4
5
5
5
5
D
E
D
E
F
H
H
H H
H
H
Dx4 Ex2 Fx1 Hx12 Jx4
H
H
H
H
H
H
J
J
J
J