modway EEI-1109 User manual

EEI-1109 & 3869 OFFICE CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 1of 4
Thank you for purchasing the MODWAY OFFICE CHAIR!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the office chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Hardware:
Components:
Bolt M6x25mm x2
1. Base x1 2. Gas Lift x1 3. Castor x5 4. Fixing Plate x1
A.
Allen Wrench x1
5. Seater Frame x1 6. Backrest x1 7. Seater x1
C.
Flat Washer x4
D.
Bolt M6x20mm x2
B.
Nut M12 x2
E.
Spring Washer M12 x2
F.
Nut Driver x1
G.

EEI-1109 & 3869 OFFICE CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 2of 4
STEP 1:
1. Attach the Backrest (6) to the Seater frame (5) by using 2 pieces of Nuts (E) and 2 pieces of
Spring Washers (F) as shown.
2. Use Nut Driver (G) to tighten all Nuts (E) clockwise as shown.
STEP 2:
1. Put the Seater (7) on the the Seater Frame (5) as shown.
2. Carefully turn over the assembled Seater Frame (5) and make sure the holes of the Seater (7) are
aligned with the holes of the Seater Frame (5) as shown.

EEI-1109 & 3869 OFFICE CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 3of 4
STEP 3:
1. Attach the Fixing Plate (4) to the Seater frame (5) and the Seater (7) by using 2 pieces of Bolts(A)
and 2 pieces of Flat Washers (C) for front as shown.
2. Attach the Fixing Plate (4) to the Seater frame (5) and the Seater (7) by using 2 pieces of Bolts(B)
and 2 pieces of Flat Washers (C) for back as shown.
3. Use Allen Wrench (D) to tighten all Bolts (A) and Bolts (B) clockwise as shown.
STEP 4:
1. Please put Base (1) on a carpeted or padded surface.
2. Insert 1 piece of Castor (3) into the Base (1) as shown by hand.
3. Repeat the same steps for the remaining 4 pieces of Castors (3).
4. Carefully turn over the assembled Base (1) and Insert the Gas Lift (2) as shown.

EEI-1109 & 3869 OFFICE CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 4of 4
STEP 5:
Insert Fixing Plate (4) into the Gas Lift (2) as shown.
Your office chair is ready to be used now!
Attention:
When you use the handle to
adjust the height to be lower,
please move away your feet
from the base at the same time.