modway MOD-6047 User manual

Customer Service 908-368-1025 www.modway.com Page 1/4
Thank you for purchasing the MODWAY BED！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that has been provided.
6.Please keep all small pieces out of reach of children.
1
2
3
4
5
6
8
9
7
12
13
14
11
MOD-6047, MOD-6078
Compenent :
1 - x 1HEADBOARD CUSHION
2 - x 1
HEAADBOARD TOP RAIL
3 - x 1HEADBOARD MIDDLE RAIL
Hardware:
AJCBB BOLT M8 x 80
JCBC BOLT M6 X 70
JCBC BOLT M6 X 60
JCBC BOLT M6 X 50
JCBC BOLT M6 X 40
WOOD DOWEL M10 X 40mm
U WASHER
B
C
D
E
F
G
4 PCS
4 PCS
2 PCS
14 PCS
2 PCS
4 PCS
2 PCS
4 - x 1
HEADBOARD RAIL
5 - x 1
HEADBOARD LEG (L)
6 - x 1HEADBOARD LEG (R)
7 - x 1SIDERAIL (L)
8 - x 1
SIDERAIL (R)
9 - x 1FOOTBOARD LEG(L)
10 - x 1
FOOTBOARD LEG(R)
11 - x 3
SUPPORT LEG
12 - x 1CENTER SUPPORT
13 - x 1
FOOTBOARD RAIL
14 - x 13
BED SLAT
10
WOOD SCREW M4 X 32mm
H10 PCS
ADJUSTER
I3 PCS
BARREL NUT
J4 PCS
SPRING WASHER M5
K4 PCS
FLAT WASHER M5
L8 PCS
ALLEN KEY (BALL SHAPE) M4
M1 PC
ALLEN KEY M5
N1 PC

Hardware & Tool required
Customer Service 908-368-1025 www.modway.com Page 2/4
Hardware & Tool required
Hardware & Tool required
Mx1
STEP 1:
1. Attach the Headboard Leg(L)(5) and Headboard Leg(R)(6)as per diagram shown. Place JCBC bolt 60MM(C) and tighten by
using M4 Allen Key(M). Then Insert JCBCbolt 40MM(E) and tighten byM4 Allen Key(N).
2. Place the Footboard Leg(L)(9) and Footboard Leg(R)(10) as per picture shown and attach JCBC bolt 50MM(D) and tighten
using M4 Allen Key(M).
STEP 2:
1.Place Headboard (1) and Side rail (L)(7) Side rail (R)(8)on a carpeted or padded area as shown. Attach Side rail (L)(7) Side rail (R)(8) into
Headboard (1) and by using JCBB 80mm Bolt (A),Spring Washer(K) into the preholes Headboard (1) and Footboard(2) as per diagram. Tighten
with M5 Allen Key (N).
2. Insert JCBC M6x70(B),Barrel Nut(J) as per diagram shown and tighten with M4 Allen Key(M) to all 4 side bed corner.
3. Attach Headborad Guardrail(3) into Headbord(1) then insert JCBC Bolt 50mm(D),Flat Washer 2mm(L) and tighten by using M4 Allen Key(M)
Ex2 Cx2
Ax4 Bx4 Jx4 Kx4 Nx1
C
Dx4 Mx1Lx4
MOD-6047, MOD-6078
Dx4

Hardware & Tool required
Customer Service 908-368-1025 www.modway.com Page 3/4
Dx2 Gx2 Mx1
Hardware & Tool required
Hardware & Tool required
STEP 3:
Place Headboard Rail(2) as diagram shown. Attach M10x40MM(F) and JCBC Bolt 50MM(D), U Washer (G) and tighten until 50%
with M4 Allen Key (M). Repeat for another side.
Ix3
Fx4
STEP 4:
1. Attach the Center Support (12) to the hinges as per diagram shown . Repeat again at Footboard(2).
2.Attach the Adjuster(J) to the three support leg(11).
3. Attach the Support Leg(11) to the Center support (12) as shown in diagram.
12
MOD-6047, MOD-6078
11
11
11

Hardware & Tool required
Customer Service 908-368-1025 www.modway.com Page 4/4
Hx10
Hardware & Tool required
Hardware & Tool required
Dx4
Assembly is completed. The bed is ready to enjoy now!
14
Screwdriver (Not provided) .
STEP 5:
Attach Slat (14) into bed by inserting CSK screw (H) into the predrilled holes on the Slat (14) . Tighten with Screwdriver (Not
provided) .
STEP 6:
1. Attach the Headboard (1) as shown in diagram. Place the JCBC bolt 50MM(D), Flat Washer(L) and tighten by using M4 Allen Key(M). Repeat
again at 3 another hole.
Mx1
Lx4
MOD-6047, MOD-6078