modway EEI -1328 User manual

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 1 of 8
EEI -1328 DESK
Hardware:
Thank you for purchasing the MODWAY DESK！
！！
！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
a Cam x30 b Cam Post x30
c Screw M4x35mm x12 d Pull Screw M4x20mm x6
e Pull x2 f Drawer Guides x3 sets
g Screw M4x14mm x30 h Dowel x32
j Knob x2 k Bolt M6x12mm x12
m n Drawer Bottom Holder x6
p Allen Wrench x1
Bolt M6x50mm x2
m Leveler x4

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 2 of 8
EEI -1328 DESK
Component:
A Top Panel x1 B Left Side Panel x1
A
C Right Side Panel x1 D Left Divide Panel x1
E Right Divide Panel x1 F Left Bottom Panel x1
G Center Bottom Panel x2 H1 Side Drawer Front x2
H2 Side Left Drawer Side x2 H3 Side Right Drawer Side x2
H4 Side Drawer Back x2 H5 Side Drawer Bottom x2
J1 Center Drawer Front x1 J2 Center Left Drawer Side x1
J3 Center Right Drawer Side x1 J4 Center Drawer Back x1
J5 Center Drawer Bottom x1 K Side Back Panel x2
L Center Back Panel x1 M Left Leg x1
N Right Leg x1
B C
F
D E
G H
H1 H1
J1
M
N
P
H2
H3
H4
H5 H5
H3 H4
H2
J2 J3
J4 J5
L
K K
P Bottom Rail x1

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 3 of 8
EEI -1328 DESK
HOW TO USE CAN AND CAM POST HARDWARE
STEP 1:
1. 2.
3. 4.
Note cam arrow
direction
Note cam arrow
direction
Turn cam clockwise
1/2 turn
5.
Place 1pc Side Drawer Front (H1),1pc Side Drawer Back (H4),1pc Left Drawer Side (H2), 1pc Right Drawer Side (H3)
and 1pc Side Drawer Bottom (H5) together as shown.
Attach them by 2pcs Cam Post (a), 2pcs Cam (b), 4pcs Screw (c), tighten the Screws (c) and Cam (b)
Attach 1pc Pull (e) to the Side Drawer Front (H1) by using 2pcs Pull Screw (d).
Fully tighten Cams (b), Screws (c), Pull Screws (d) with Phillips Head Screw Driver (not included).
Repeat the same steps and hardware for the other Side Drawer.
ax4 bx4 cx8 dx4 ex2
Phillips Head Screwdriver
( not included) Hardware & Tools required
h
H1
d
H2
H3
H4 H5
a
a
b
b
c
c d e

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 4 of 8
EEI -1328 DESK
STEP 3:
Place the assembled Center Drawer upside down on a carpeted or padded surface.
Attach the 6pcs Drawer Bottom Holder (n) to the bottom of the assembled Center Drawer by using 6 pcs Screw (g) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Screws (b) clockwise until secure.
gx6 nx6 Phillips Head Screwdriver
( not included) Hardware & Tools required
J2
e
STEP 2:
Place 1pc Center Drawer Front (J1),1pc Center Drawer Back (J4),1pc Center Left Drawer Side (J2),
1pc Center Right Drawer Side (J3) and 1pc Center Drawer Bottom (J5) together as shown.
Attach them by 1pc Cam Post (a), 1pc Cam (b), 4pcs Screw (c), tighten the Screws (c) and Cam (b)
Attach 2pcs Knob (e) to the Center Drawer Front (H1) by using 2pcs Pull Screw (d).
Fully tighten Cams (b), Screws (c), Pull Screws (d) with Phillips Head Screw Driver (not included).
ax2 bx2 cx4 dx2 jx2
Phillips Head Screwdriver
( not included) Hardware & Tools required
J3
J1
J5
J4
e
d
d
a
a
b
b
j
j
J1 J3
J5
J2 J4
g
n n
n
g
g g g

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 5 of 8
EEI -1328 DESK
STEP 4:
STEP 5:
Place the Left Side Panel (B), Right Side Panel (C), Left Divide Panel (D) and Right Divide Panel (E) upside down
on a carpeted or padded surface.
Attach the 3 sets Drawer Guides (f) to the Left Side Panel (B), Right Side Panel (C), Left Divide Panel (D) and
Right Divide Panel (E) by using 12pcs Screw (g) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Screws (g) clockwise until secure.
Insert 20pcs Cam Post (a) into the corresponding holes on the Top Panel (A), Left Divide Panel (D) , Right Divide Panel
(E), Left Bottom Panel (F) and Right Bottom Panel (H) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Cams (a) clockwise until secure.
Insert 26pcs Dowel (h) into the corresponding holes on the Top Panel (A), Left Divide Panel (D) , Right Divide Panel (E),
Left Bottom Panel (F) and Right Bottom Panel (H) as shown.
ax20 hx26 Phillips Head Screwdriver
( not included) Hardware & Tools required
A
Hardware & Tools required
fx3 gx12 Phillips Head Screwdriver
( not included)
B
C D
E
C
C
f
f
g
g
g
g g
g
g
g
g
g g
g
g
g
D
E
F H
h h h
h h h
h h
h
h
h
h
h
h
a
a a a
a
a a
a
a a
a
a
h
h
h
h
a
a
h
h
h
h
a
a
h
a a h
h
h
a
a

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 6 of 8
EEI -1328 DESK
bx8 Phillips Head Screwdriver
( not included)
STEP 7:
STEP 8:
Place the Left Divide Panel (D), Right Divide Panel (E) and Center Back Panel (L) to the Center Bottom Panel (G) as shown.
Attach them by using 12pcs Cam (b) and 2pc Dowel (h).
Use Phillips Head Screwdriver (not included) to tighten the Cams (b) clockwise until secure.
Place the Left Side Panel (B), Right Side Panel (C), Side Back Panel (K) and the Assembled Left Divide Panel (D),
Right Divide Panel (E), Center Back Panel (L) to the Top Panel (A) as shown.
Attach them by using 8pcs Cam (b) .
Use Phillips Head Screwdriver (not included) to tighten the Cams (b) clockwise until secure.
Hardware & Tools required
Hardware & Tools required
bx4 Phillips Head Screwdriver
( not included)
hx2
D
E
G
L
b b
b
b
h h
B
C D
E G
A
L
K K
b
b
b
b b
b

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 7 of 8
EEI -1328 DESK
hx4 Phillips Head Screwdriver
( not included)
bx8
STEP 9:
STEP 10:
Please put Assembled Top Panel(A1&A2) upside down on a carpeted or padded surface.
Place the Bottom Panel (B) to the assembled Side Panels (C&D),
, ,
, Divide Panels (E&F) and Back Panel (G) as shown.
Attach them by using 12pcs Bolt (j).
Use Allen Wrench (q) to tighten the Bolts (j) clockwise until secure.
Hardware & Tools required
Hardware & Tools required
G B C D
E
K K
F E
h h h h
b
b b b b
b
Place the Left Leg (M), Right Leg (N) and Bottom Rail (P) upside down on a carpeted or padded surface as shown.
Attach them by using 2pcs Bolt (m).
Use Allen Wrench (p) to tighten the Bolts (q) clockwise until secure.
M N
P
mx2 px1
m
p p
m

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 8 of 8
EEI -1328 DESK
STEP 10:
Please put the assembled desk’s top upside down on a carpeted or padded surface as shown .
Attach assembled Left Leg (M) and Right Leg (N) into the bottom of the Left Bottom Panel (F) and Right Bottom
Panel (H) by using 12pcs Blot (k).
Use Allen Wrench (p) to tighten the Bolts (k) clockwise until secure.
Hardware & Tools required
kx12 px1 mx4
STEP 11:
M
J
m
p
Pull out the 3 sets metal drawer guides of Drawer Guides (f).
Attach the Side Drawers and Center Drawer to the Drawer Guides (f) by using 12pcs Screws (g).
Use Phillips Head Screw Driver (not included) to tighten the Screws (g) clockwise until secure.
N
P
m
m
m
F
H
gx12 Phillips Head Screwdriver
( not included) Hardware & Tools required
A
B C
g
g g
g
g
g
g
g g
g
g
g

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 9 of 8
EEI -1328 DESK
STEP 12:
Carefully turn over the desk.
Rotate the adjustable feet on bottom of each leg to desired height and leveling according to your floor surface.
Assembly is completed. The desk is ready to enjoy now!