modway EEI-3864 User manual

Customer Service 908-368-1025︱www.modway.com Page 1 of 17
Thank you for purchasing the MODWAY TV STAND !
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 120 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
EEI-3864 TV STAND
Owing to the size and weight of the TV Stand, we recommend that
Q) Grommet Hole Cover/Plastic
x 1
L) Screw/Metal
M 6 x 10.5 mm x 16
G) Pin Sliding Top/Plastic
Ø 8 x 19 mm x 4
B) CamLock/Metal
Ø 15 mm x 12
M) Plate/Metal
80 x 90 mm x 4
H) Pin Sliding Bottom/Plastic
Ø 8 x 16 mm x 4
C) Dowel Big/Wood
Ø 8 x 30 mm x 34
P) Wall plug
5002 x 14
K) Screw/Metal
M 6.4 x 25 mm x 20
F) Hex /Allen Key/Metal
L 4 x 1
A) Cambolt/Metal
Ø 6 x 35 mm x 12
Bracket Set/Metal
x 1
R)
N) Shelf Pin/Metal
Ø 5 x 15 mm x 4
I) Stopper/Plastic
42 x 14 x 8 mm x 2
D) Dowel Small/Wood
Ø 8 x 20 mm x 22
O) Screw/Metal
M 12 x 45 mm x 13
M 12 x 55 mm x 1
J) Buffer/Rubber
Ø 8 mm x 1
E) Screw/Metal
M 7 x 50 mm x 19
Hardware :
Screw/Metal
x 4
S)
M 6 x 15 mm
T)
R1)
R (BRACKET SET)
R7) R8)
R2) R3) R4)
R5) R6)
M 6 x 45 mm
M 6 x 30 mm M 8 x 30 mm
Bracket/Metal
x 1
Bracket/Metal
x 1
Screw/Metal
Screw/Metal Screw/Metal
x 2 x 4
x 4 x 4 x 4
Ø16 mm x 4 Ø16 mm
Screwdriver (Not Include)
Waterpass (Not Include)
Drill (Not Include)
U) x 1
V) x 1
W) x 1

Customer Service 908-368-1025︱Page 2 of 17www.modway.com
Components:
6
7
8
8
9
10
11
12
13
14
15
15
15
15
16
17
18
18
19
20
22
14
5
1 2 3
67
4
8
10 11 12
9
14 15 16
13
21 22
18
17 19 20
Top Board x1
Centre Board Left x1
Centre Board Top x4 Mdf Support x2 Centre Board Top x4 Support Wall Panel 1 x2
Back Board x1 Wall Panel 1 x1 Wall Panel 2 x1 Wall Panel 3 x1
Centre Board Right x1 Adjustable Shelf x1 Frame Door x2
Bottom Board x1 Side Board Left x1 Side Board Right x1
Support Wall Panel 2 x1
Support Wall Panel 6 x4
Support Wall Panel 3 x2
Support Wall Panel 7 x1
Support Wall Panel 4 x1 Support Wall Panel 5 x1
16
EEI-3864 TV STAND
21
21
21
21

Customer Service 908-368-1025︱Page 3 of 17www.modway.com
STEP 1:
Hardware required.
Screwdriver not included
Ax12 Cx24 Ux1
6
20
19
EEI-3864 TV STAND
PART 1 : ASSEMBLE BASE UNITPART 1 : ASSEMBLE BASE UNIT

Customer Service 908-368-1025︱Page 4 of 17www.modway.com
STEP 2:
STEP 3:
Hardware required.
Screwdriver not included
Bx4 Ux1
6
19
20
EEI-3864 TV STAND

Customer Service 908-368-1025︱Page 5 of 17www.modway.com
STEP 4:
STEP 5:
Hardware required.
Screwdriver not included
Bx8 Ux1
9
Hardware required.
Ex8Fx1
EEI-3864 TV STAND
Base Unit Ready for Installation (Part 3)

Page 6 of 17Customer Service 908-368-1025www.modway.com
STEP 7:
13
15
15
15
15
Hardware required.
Ex4 F
PART 2 : ASSEMBLE WALL UNIT
EEI-3864 TV STAND
STEP 6:
Hardware required.
Cx10
15

Customer Service 908-368-1025︱ Page 7 of 17 www.modway.com
STEP 8:
STEP 9:
10
11
12
EEI-3864 TV STAND
14
16
17
18
Hardware required.
Dx22

Customer Service 908-368-1025︱Page 8 of 17www.modway.com
STEP 10:
STEP 11:
Hardware required.
Kx12 F
Lx16
Hardware required.
Screwdriver not included
Ux1
16
16
10
EEI-3864 TV STAND

Hardware required.
Ex7Fx1
13 10
STEP 12:
Kx8 F
Hardware required.
Screwdriver not included
Customer Service 908-368-1025︱Page 9 of 17www.modway.com
EEI-3864 TV STAND
STEP 13:
Wall Unit Ready for Installation (Part 3)

Customer Service 908-368-1025︱Page 10 of 17www.modway.com
( 585 ) ( 585 )
14.1. Determine your Base Unit center
position on the wall (X).
It’s 585 mm from the edge of Base unit.
14.2. Determine your desired (Y)
height, then subtract by 82 mm.
This is the drill holes height from
the floor.
14.3. Continue to complete measurment on drill holes position on the wall.
#refer to page 11 (Step 14.4)
#refer to page 11 & page 12
( Z )
82
( Y )
*Unit in millimeter (mm)
PART 3 : Preparations for mounting items to the wall
EEI-3864 TV STAND
STEP 14: