modway EEI-2155 User manual

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 1 of 4
EEI –2155 OFFICE CHAIR
Hardware:
Component:
1 Bolt M6x18mm x8
2 Allen Wrench x1
Thank you for purchasing the MODWAY OFFICE CHAIR！
！！
！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the office chair, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approximate assembly time: 15 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
B
A
C
F
3 Plastic Cover x6
F
E
A Chair Back with Arm x1 B Chair Seat x1 C
D
Control Mechanism x1
E Chair Base x1 F Castor x5 Cylinder Column x1
F
F
D

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 2 of 4
EEI –2155 OFFICE CHAIR
STEP 1:
STEP 2:
Please put the Chair Base (E) upside down on a carpeted or padded surface.
Insert 1pc of Castor (F) into the Chair Base (E) as shown by hand.
Repeat the same steps for the other 4pcs of Castor (F).
E
F
F
F
F
F
1x4pcs 2x1pc 3x6pc Hardware & Tool required
Place a sealed carton on the floor with a carpeted or padded surface on the top side of carton.
Please put a heavy object into the carton for balance prior to assembling the office chair.
Place the Chair Seat (B) upside down on the carton.
Attach the Chair Back with Arm (A) into the bottom of Chair Seat (B) by using 6 piece of Bolts (1) as shown.
Use Allen Wrench (2) to tighten the Bolts (1) clockwise until secure.
Insert the 6 pieces of Plastic Covers (3) into the corresponding holes on the side of Chair Back with Arm (A) as shown.
B
A
B
A
3
3
1
1
1
1 2
3
1
3
1 3

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 3 of 4
EEI –2155 OFFICE CHAIR
STEP 3:
STEP 4:
1x4pcs 2x1pc Hardware & Tool required
Attach the Control Mechanism (C) into the bottom of Chair Seat (B) by using 4 piece of Bolts (1) as shown.
Use Allen Wrench (2) to tighten the Bolts (1) clockwise until secure.
Insert the Cylinder Column (D) into the Bottom of Control Mechanism (C) as shown.
C
D
B
C
A
A
B
1
1
1 1
1
2

Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 4 of 4
EEI –2155 OFFICE CHAIR
STEP 5:
STEP 6:
Insert the assembled Chair Base (E) into the Cylinder Column (D) as shown.
Carefully turn over the office chair.
Place the armrests to the correct position for using.
E
D