modway EEI-1326 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI -1326 DESK
Component:
Thank you for purchasing the MODWAY DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
Hardware:
a Bolt M6x12mm x12
d Nut x8
e Leveler x4
g Allen Wrench x1
h Open Wrench x1
A Top Panel x1 B Leg x2
G Back panel x1
A
C
B
B
b Bolt M6x23mm x8
c Bolt M6x25mm x4
D
D
E
E
E
E
F
F
G H
C Center Rail x1
D Connect Rail x2 E Back Stretcher x4 F Tray x2
H Pen Box x1
f Flat Washer x4

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI -1326 DESK
STEP 1:
STEP 2:
Please put the Top Panel (A) upside down on a carpeted or padded surface as shown .
Attach the assembled Legs (B) into the bottom of Top Panel (A) by using 4pcs Bolts (a).
Use Allen Wrench (g) to tighten the Bolts (a) clockwise until secure.
Secure the 4pcs Levelers (e) to the bottom of the Legs (B) clockwise until secure as show.
ax4 cx4 gx1 Hardware & Tool required
ax8 dx8 gx1 hx1 Hardware & Tool required
Please place the Center Rail (C) and 2pcs of Legs (B) as shown.
Attach one of Legs (B) to the Center Rail (C) by using 4pcs Bolts (a) and 4pcs Nut (d) as shown.
Full tighten the Bolts (a) and Nuts (d) by using Allen Wrench (g) and Open Wrench (h).
Repeat the same steps for the other Leg (B) to the Center Rail (C).
A
B
B
C
a
a
a
a
a
g
B
A
e
e
B
B
C
B
C
g
a
d
h d
a
a
d d
d d
a

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI -1326 DESK
STEP 3:
Carefully turn over the desk.
Attach one piece of Connect Rail (D) the Center Rail (C) by using 2pcs Bolts (b) from the bottom of the Top Panel (A) as shown.
Full tight the Bolts (b) with the Allen Wrench () as shown.
STEP 4:
bx2 gx2 gx1 Hardware & Tool required
cx4 gx1 Hardware & Tool required
A
D
D
A
D b
b
g
Attach the Connect Rail () the Center Rail (C) by using 2pcs Bolts (b) from the bottom of the Top Panel (A) as shown.
Full tight the Bolts (b) with the Allen Wrench (g) as shown.
Hang the Back Panel (G) on the Back Stretcher (E) as shown.
D
E
G
A
D
b b
g E
g
g

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI -1326 DESK
STEP 6:
Assembly is completed. The desk is ready to enjoy now!
Please hang the 2pcs of Tray (F) and Pen Box (H) on the Back Stretchers (E) as shown.
Rotate the adjustable feet on bottom of each leg to desired height and leveling according to your floor surface.
F
F
E
E E
E
G H
bx6 fx6 gx1 Hardware & Tool required
Insert the remain three Back Stretcher (E) from the side of the Back Panel (G) as shown.
Then attach them to the Connect Rail () by using 6pcs Bolts (b) and 6pcs Flat Washer (f) as shown.
Full tight the Bolts (b) with the Allen Wrench (g) as shown.
Note: The bottom of the Back Stretcher (E) should be locked by the Back Panel (G).
STEP 5:
E
E
E E
D
D
D
E
b g
f
b
b
b
b
b
b f
f
f
f
f
f
G