modway MOD-6007 User manual

Thank you for purchasing the MODWAY BED!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step instructions.
2. Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
1JCBC BOLT M6 x 30 20 PCS
2JCBB BOLT M8 x 70 2 PCS
3FLAT WASHER M6 20 PCS
4SPRING WASHER M6 20 PCS
5FLAT WASHER M8 2 PCS
6SPRING WASHER M8 2 PCS
7WOOD SCREW M3.5 x 16mm 8 PCS
8BED SLAT SIDE FITTER 26 PCS
9BED SLAT CENTER FITTER 13 PCS
10 ALLEN KEY (BALL SHAPE) M4 1 PC
Component:
A. HEADBOARD x 1
B. FOOTBOARD x 1
C. SIDE RAIL (L&R) x 2
D. CENTER RAIL x 1
E. CENTER SUPPORT LEG x 3
F. CENTER SUPPORT x 2
G. BED SLAT x 26
H. LEG x 4
01 of 05
MOD - 6007 / 6008 QUEEN BED
A
BC
D
F
E
G
H
11 ALLEN KEY (BALL SHAPE) M5 1 PC

STEP 1
1.1 Fasten center support leg (D) to center rail (E) attach by screwing the protruding nut into
the corresponding holes.
02 of 05
DE
B
A
11
11. ALLEN KEY (BALL SHAPE) M5 x 1pc
1.1 Loosen the pre-inserted bolt on the headboard and footboard using Allen key ball shape (11).
MOD - 6007 / 6008 QUEEN BED

STEP 2
2. JCBB BOLT M8 x 70 x 2pcs 6. SPRING WASHER M8 x 2pcs 5. FLAT WASHER M8 x 2pcs 11. ALLEN KEY (BALL SHAPE) M5 x 1pc
1. JCBC BOLT M6 x 30 x 20pcs 4. SPRING WASHER M6 x 20pcs 3. FLAT WASHER M6 x 20pcs 10. ALLEN KEY (BALL SHAPE) M4 x 1pc
03 of 05
C A
STEP 2.1
X 2
STEP 2.2
265
11
A
C
143
H
10
H
2.1 Attach the side rails (C) to the headboard (A) & footboard (B)
3.1 Assemble bed leg ( H ) JCBC Bolt M6 x 20mm x 20pcs (1),M6 spring washer x 20pcs (4)
and M6 flat washer x 20pcs (3) on each leg using M4 allen key (10)
2.2 Insert and secure the Headboard (A) to the side rail (C) using hardware parts 2,5,6 and
11.
STEP 3
MOD - 6007 / 6008 QUEEN BED

STEP 4
STEP 5
04 of 05
D
A
C
7
F
7. WOOD SCREW M3.5 x 16 x 8pcs Screw Driver
4.1 Locate center rail (D) into the corresponding brackets inside of headboard (A) and
footboard (B).
5.1Insert and secure the center rail support (F) to the side rail (L/R) (C) using hardware parts
7 & screwdriver.
MOD - 6007 / 6008 QUEEN BED

STEP 6
Assembly is complete. The bed is ready to use now!
NOTE: Hardware may loosen over time. Periodically check that all connections are tight. 05 of 05
Palm
Palm G
G9
8
8
G
8
9
G
G
STEP 7
8. BED SLAT SIDE FITTER x 26pcs 9. BED SLAT CENTER FITTER x 13pcs
6.1 Insert the slats (G) into the end slat cap (8)&(9) and fix it to the corresponding holes on
the side rail (C)
7.1 Carefully position the assembled bed to the desired location by four adults.
MOD - 6007 / 6008 QUEEN BED