modway EEI 2806 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI–2805/2806 TABLE
Hardware:
Component:
A Double-End Bolt x 4
Thank you for purchasing the MODWAY TABLE!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
C Spring Washer 1/4” x 8
Table Glass x1 2 Table Top x1 3 Table Leg x4
1
1
D Flat Washer 1/4” x 8
E Wrench 1/4” x 1
F Plastic Cover x 4
B Nut 1/4” x 8
3
3
3
3
2

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI–2805/2806 TABLE
STEP 1:
STEP 2:
Secure 1 piece of Nut (B) into one end of Double-end Bolt (A) by hand as shown.
Repeat the same steps for the remaining Double-end Bolts (A).
Hardware & Tool required
B A
2
Ax4 Bx4
Cx4 Dx4 Hardware & Tool required
Please put Table Top (2) upside down on a carpeted or padded area.
Secure 4 pieces of Double-End Bolt (A) into the bottom of Table Top (2) as shown.
Secure the assembled Nuts (B) at step 1 to Table Top (2) tightly by hand.
A
A
A
A
2
D
C
A
D
C
B
B
C
D
B
D
C
B
C
D
B

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI–2805/2806 TABLE
STEP 3:
STEP 4:
Put 4 pieces of Table Leg (3) to Table Top (2) through the assembled Double-End Bolt (A) as shown.
2
3
3
3
3
Bx4 Ex1 Cx4 Dx4
Secure 4 pieces of Nut (B), 4 piece of Spring Washer (C), and 4 pieces of Flat Washer (D) to the end of assembled
Double-End Bolt (A) as shown.
Use Wrench (E) to tighten Nuts (B) clockwise until secure.
2
3
3
3
3
E
B
C
D
3
E
B
C D
D
C B
D
C B
D
C B

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI–2805/2806 TABLE
STEP 5:
STEP 6:
Insert 4 pieces of Plastic Cover (F) into the assembled Table Leg (3) as shown.
Carefully turn over the assembled table.
Put Table Glass (1) to the Table Top (2) as shown.
Gx4 Hardware & Tool required
3
Assembly is complete. Your table is ready to be used now!
3
2
3
3
F
1
2
3
3
3
3
F
F
F