modway EEI-2712/2713 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI-2712/2713 TABLE
Hardware:
Component:
1 Table Top x1
Thank you for purchasing the MODWAY TABLE！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
1
3 Leg II x2
3
A Long Bolt M8x70m x8
G Allen Wrench M4 x1
2
2
B
Flat Washer M8 x8
C
Spring Washer M8 x8
4
4
5
2 Leg I x2
4 Stretcher x2 5 Bottom Rail x2
E
Short Bolt M6x40mm x2
F
D Open Wrench M5 x1
Medial Bolt M6x60mm x4

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI-2712/2713 TABLE
STEP 1:
Please put 1 piece of Leg I (2) and 1 piece of Leg II (3) upside down on a carpeted or padded area.
Position 1 piece of Stretcher (4) to the Leg I (2) and Leg II (3) as shown.
Insert the tenon on Stretcher (4) into the Rabbet on the Leg I(2) and Leg II(3).
Insert 2 pieces of Medial Bolt (E) into the holes on Stretcher (4) through the holes on Leg I (2) and Leg II (3).
Use Allen Wrench (G) to tighten Medial Bolts (E).Do not fully tighten Medial Bolts (E) at this step.
Repeat the same steps for the remaining Leg I(2), Leg II(3) and Stretcher (4).
STEP 2:
Hardware & Tool required
Ex8 Gx1
E
Please put the Table Top (1) upside down on a carpeted or padded area.
Position the assembled Leg I (2), Leg II (3) and Stretcher (3) into the corner of Table Top (1) as shown.
Insert 4 pieces of Long Bolt (A) with 4 pieces of Spring Washer (B) and 4 pieces of Flat Washer (C) into the pre-drilled
holes on bottom of Leg I (2) and Leg II (3) through the pre-drilled holes on Table Top (1).
Use Open Wrench (D) to tighten Long Bolts (A) clockwise until secure.
3
2
3
2
4
4
E
E
E
G
Hardware & Tool required
Ax4 Dx1 Bx4 Cx4
1
2
3
4
A
B
C
D

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI-2712/2713 TABLE
STEP 3:
Position the other sets of assembled Leg I(2), Leg II(3) and Stretcher (3) into the corner of Table Top (1) as shown.
Insert the tenon on the end of Bottom Rail(5) into the rabbet of Stretchers(4).
Insert 4 pieces of Long Bolt (A) with 4 pieces of Spring Washer (B) and 4 pieces of Flat Washer (C) into the pre-drilled holes
on bottom of Leg I(2) and Leg II(3) through the pre-drilled holes on Table Top (1).
Use Open Wrench (D) to tighten Long Bolts (A) clockwise until secure.
STEP 4:
Hardware & Tool required
Ax4 Dx1 Bx4 Cx4
A
A
Insert 2 pieces of Short Bolt (F) into the holes on Bottom Rail (5) through the holes on Stretchers (4).
Use Allen Wrench (G) to tighten all the Medial Bolts (E) and Short Bolts (F).
Use Open Wrench (D) to tighten all Long Bolts (A) clockwise until secure.
B
C
D
B
D
1
3
2
4
5 3
2 4
Hardware & Tool required
Dx1 Gx1 Fx2
1
2
2
3
3
4
4
5
D
F
F
G

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI-2712/2713 TABLE
STEP 5:
Carefully turn over the assembled table.
Assembly is completed. Your table is ready to be used now!