modway Expedite EEI-3039 User manual

EEI-3039 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1of 5
Thank you for purchasing the MODWAY OFFICE CHAIR.
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A. Bolt M6x18mm x 4
B. Bolt M6x30mm x 4
C. Bolt M8x25mm x 4
D. Cover x 8
E. Allen Wrench M6 x1
Component:
1 Base x1 2 Cylinder Column x1 3 Control Mechanism x1 4 Seat x1
5 Back Frame x1 6 Left Arm x1 7 Right Arm x1 8 Castor x5
5
4
3
1
6
7
8
8 8
8

EEI-3039 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2of 5
4
6
B
E
C
E
5
3
STEP 1:
Please put Seat (4) on a carpeted or padded surface.
Attach Control Mechanism (3) to the bottom of Seat (4) by using 4 pieces of Bolts (A) as shown.
Tighten Bolts (A) by using Allen Wrench (E) as shown.
Hardware & Tools required
STEP 2:
Attach Left Arm (6) to the Seat (4) and Back Frame (5) by using 2 pieces of Bolts (B) and 2 pieces of Bolts (C)
as shown. Tighten Bolts (B) & (C) by using Allen Wrench (E) as shown.
Hardware & Tools required
A
x 1
x 4
E
3
4
A
E
B
x 2 x 2
C
x 1
E

EEI-3039 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3of 5
STEP 3:
Attach Right Arm (7) to the Seat (4) and Back Frame (5) by using 2 pieces of Bolts (B) and 2 pieces of Bolts (C)
as shown. Tighten Bolts (B) & (C) by using Allen Wrench (E) as shown.
Hardware & Tools required
STEP 4:
Insert 1 piece of Castor (8) into the Base (1) as shown by hand.
Repeat the same steps for the remaining 4 pieces of Castors (8).
B
x 2 x 2
C
x 1
E
7
4
3
5
C
E
B
E
6
8
8
8
8
8
8

EEI-3039 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4of 5
STEP 5:
Insert the bottom end of Cylinder Column (2) into the assembled Base (1) as shown.
STEP 6:
Insert the bottom holes of Control Mechanism (3) into the top end of Cylinder Column (2) as shown.
1
2
2
1
1
4
3
6
7
5
2

EEI-3039 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5of 5
STEP 7:
Fully tighten all Bolts by using Allen Wrench.
Attach 8 pieces of Covers (D) into the holes of Left Arm (6) and Right Arm (7) as shown.
Hardware & Tools required
STEP 8:
Assembly is completed. Your office chair is ready to be used now!
6
7
D
D
D
x 8