modway MOD-5465 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
MOD-5465/5466 BED
Hardware:
Component:
ABolt M8x35mm x4
F
Flat Washer x8
I
Allen Wrench x1
1Headboard x1 2Footboard x1
4
Thank you for purchasing the MODWAY BED！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
Leg x4
5
Side Rail x2 6Center Rail x1
7
Support Leg x2
BBolt M8x25mm x12
E
Spring Washer x8
D
Nut M8 x4
G
End Plastic Cover x28
H
Center Plastic Cover x14
Slat x28
C
Open Wrench x1
3
1
2
3
4
5
7
3
46
7
3
3
Bolt M8x25mm x8
J

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
MOD-5465/5466 BED
Cx8 J x1
STEP 1:
Attach Legs (3) into Headboard (1) and Footboard (2) as shown.
Secure by using 4 pieces of Bolt (C) .
Using Allen Wrench (J)to tighten Bolts (C) clockwise until secure.
Hardware & Tool required
STEP 2:
Place 1 piece of Side Rail (4) to Headboard (1) and Footboard (2) as shown.
Attach each end of Side Rail (4) by using 2 pieces of Bolt (B), 2 pieces of Spring Washer (F) and 2 pieces of Flat Washer (G).
Using Allen Wrench (J)to tighten Bolts (B) clockwise until secure.
Repeat the same steps for remaining Side Rail (4).
Hardware & Tool required
1
2
3
3
3
3
3
1/2
C
J
C
Bx8 Fx8 Gx8 Jx1
4
4
1
2
1
4B
F
G
J
B
G
F

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 3
MOD-5465/5466 BED
STEP 3:
Assembly is complete. Your bed is ready to be enjoyed now!
Ax4 Bx4 Dx1 Ex4 Jx1 Hardware & Tool required
1
5
6 5
Attach Support Legs (6) to Center Rail (5) by using 4 pieces of Bolt (A) and 4 pieces of Nut (E) as shown.
Use Allen Wrench (J) and Open Wrench (D) to tighten Bolts (A) and Nuts (E) until secure.
Place each end of assembled Center Rail (5) to Headboard (1) and Footboard (2).
Attach by using 2 pieces of Bolt (B) to each end of Center Rail (5) as shown.
Use Allen Wrench (J)to tighten Bolts (B) clockwise until secure.
6 2
6
D
E
A A
J
J
B
B
1 5
Hardware & Tool required
Hx28 I x14
STEP 4:
Insert 2 pieces of Slat (7) into 2 pieces of End Plastic Cover (H) and 1 piece of Center Plastic Cover (I ) as shown.
Then insert the assembled Center Plastic Cover (I) into the holes on Center Rail (5), and the assembled End Plastic
Covers (H) into the holes on Side Rail (4) as shown.
Repeat the same steps for remaining 26 pieces of Slat (7).
4
4
5
7
7
H
I H
H
H
4
4
E