MOEM 3-Wheel Combination Lock DW User manual

Instruction Manual
3-Wheel Combination Lock (DW)
____________________________________________________________________________________
____________________________________________________________________________________
Version 2.0: 3/12/2018 Page | 1
NOTE: READ COMPLETE INSTRUCTIONS BEFORE OPERATING THE LOCK OR CHANGING THE COMBINATION
Important: Turn dial slowly and evenly. Do not turn back to regain alignment if you rotate past number. If an error is made, clear
and re-dial entire combination. Do not count turns. Count how many times each number is aligned with the opening index (at the 12
o'clock position). Always view dial and ring straight on, not at an angle. It is the owners’ responsibility to maintain the code.
TO OPEN (Factory setting 10-20-30)
1. Turn anti-clockwise ↺ (Left) 4 times (10) or (your 1st number),
stopping when (10) is aligned with the opening line the fourth time
2. Turn clockwise ↻(Right) 3 times (20) or (your 2nd number), stopping
when (20) is aligned with the opening line the third time
3. Turn anti-clockwise ↺(Left) 2 times (30) or (your 3rd number),
stopping when (30) is aligned with the opening line the second time
4. Turn clockwise ↻until stop
(If correctly done, number should stop at zero on the opening line)
CHANGING TO A NEW COMBINATION
NOTE: With door in opening position, turn handle so that bolts in a shooting position
STEP 1:Insert existing numbers (e.g. 10-20-30) on setting/resetting line
1. Turn anti-clockwis ↺(Left) 4 times (10) or (your 1st number), stopping when (10) is aligned with the
setting / resetting line the fourth time
2. Turn clockwise ↻(Right) 3 times (20) or (your 2nd number), stopping when (20) is aligned with the
setting/ resetting line the third time
3. Turn anti-clockwise ↺(Left) 2 times (30) or (your 3rd number), stopping when (30) is aligned with the
setting/resetting line the second time
4. At last number, hold the combination dial lock
NOTE: If the number is inserted correctly, you will be able to insert change key (STEP 2)

Instruction Manual
3-Wheel Combination Lock (DW)
____________________________________________________________________________________
____________________________________________________________________________________
Version 2.0: 3/12/2018 Page | 2
STEP 2: Insert change key into the key hole (Back of door)
1. Insert L-Shape key into key hole *(Refer to diagram 1.0 marked “A”with
arrow pointing down)
2. Insert L-Shape Key completely pointing downwards *(Refer to
diagram 1.0 marked “X”shown maximum point of insertion)
3. Turn Change Key anti-clockwise ↺(Right) 90 degrees
STEP 3 :Insert new numbers (e.g. 30-40-50) on setting/resetting line
1. Turn anti-clockwise ↺(Left) 4 times (30) or (your 1st number),
stopping when (30) is aligned with the setting/resetting line the fourth time
2. Turn clockwise ↻(Right) 3 times (40) or (your 2nd number), stopping when (40) is aligned with the
setting/resetting line the third time
3. Turn anti-clockwise ↺(Left) 2 times (50) or (your 3rd number), stopping when (50) is aligned with the
setting/resetting line the second time
4. Stop at last number on setting / resetting line (* Note that last number must be above 20)
5. Turn change key clockwise ↻(Left) 90 degrees and pull out
6. Changing of combination lock is completed
NOTE: DO NOT TURN BACK TO REGAIN PROPER ALIGNMENT IF EXCEEDED NUMBER. REPEAT
PROCESS FROM BEGINNING OF STEP 3
IMPORTANT !!: Please check using new numbers on opening line repeatedly before locking
For support contact us or our local distributor/ agent
For additional support please visit :
Website : www.moem.com.my
Youtube : Moem Malaysia