MONKEY GRIP SPEED DRIVE 17045-MG User manual

17045-MG
Inflates Car Tires & Other Inflatables
ATTENTION! READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE USE
If you experience any problems with this product,
do not return it to or contact the store where it was purchased.
Contact Hopkins Manufacturing Technical Support at 1-800-524-1458.
Hopkins Manufacturing Corporation • 428 Peyton St., Emporia, KS 66801
INSTRUCTIONS FOR USE
SPEED
DRIVE™
TIRE INFLATOR

Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better
and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert
Read The Operator’s Manual
Eye Protection
Wet Conditions Alert
Hot Surface
Indicates a potential personal injury hazard
To reduce the risk of injury, user must read and
understand operator’s manual before using this product
Do not expose to rain or use in damp locations
To reduce the risk of injury or damage, avoid contact
with any hot surface
Always wear eye protection with side shields marked to
comply with ANSI Z87.1
INSPECT INFLATOR AFTER UNPACKING
After unpacking your inflator, carefully inspect the inflator to ensure there is no damage that may
have occurred during transit and verify all components have been included as listed and shown
on page 5
IMPORTANT! READ ALL INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO USE THIS
INFLATOR. FAILURE TO FOLLOW WARNINGS AND COMPLY WITH ALL INSTRUCTIONS
COULD RESULT IN FIRE, PROPERTY DAMAGE OR INJURY TO PERSONS
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION
OPERATE INFLATOR WITH 12 VOLT DC POWER OUTLETS RATED 15 AMPS OR HIGHER. DO
NOT USE WITH OLDER 8 AMP CIGARETTE LIGHTER RECEPTACLES
DO NOT USE INFLATOR CONTINUOUSLY FOR MORE THAN 10 MINUTES. ALLOW UNIT TO
COOL BETWEEN USES
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
INTRODUCTION
TABLE OF CONTENTS
2
Introduction______________________________________________________________________________2
General Safety Rules and Warnings________________________________________________________3
Quick Start Guide_________________________________________________________________________4
Featured Product Illustrations______________________________________________________________5
Inflator Operation_________________________________________________________________________6
Inflating Tires_________________________________________________________________________6
Inflating Sports Balls or Other High Pressure Small Inflatables_______________________________6
Maintenance_____________________________________________________________________________7
Trouble Shooting_______________________________________________________________________7-8
Warranty_________________________________________________________________________________8
Contact Us_______________________________________________________________________________8

GENERAL SAFETY RULES & WARNINGS
3
�Keep children and others away while operating inflator
�Keep the inflator dry, clean and free from oil and grease. Always use a clean cloth when
cleaning. Never use typical vehicle fluids such as brake fluid, gasoline, any petroleum
products or strong solvents to clean inflator
�Operate inflator in an open area and away from any objects that could restrict the flow of air
to ventilation openings
�Do not operate inflator near fire, flammable liquids or in gaseous or explosive atmospheres
Always wear eye protection
�Always use in a safe area away from traffic and other dangers
�Do not attempt to disassemble inflator. No user serviceable parts inside. Only user
serviceable part is fuse replacement. See maintenance section on page 7
�Before each use, always check inflator hoses and 12 Volt cord for weak or worn condition
and make certain all connections are secure. Do not use if a defect is present
�Do not pull or carry the inflator by the power cord or air hose
�Do not over stretch power cord or air hose
�Never point an inflator air hose toward yourself, others or animals
�Never start a vehicle with the inflator plugged into a 12 Volt DC power outlet. See operation
instructions on pages 4-6
�Use the inflator for its intended use only. Do not alter or modify the inflator
Do not store inflator in a damp or wet location. Protect the inflator from rain, snow or other
moisture sources
�When not in use, make certain the inflator power button is in the off position
Store inflator out of the reach of children
�IMPORTANCE OF PROPER TIRE PRESSURE
— Correct tire pressure is vital to road safety
— Correct tire pressure can help improve vehicle fuel economy
— Regularly check tires on vehicles to meet manufacturer’s recommended tire pressure
— Always check pressures at ambient temperature, never check immediately following a
long trip
WARNING:
— For the safety of your vehicle and your new tire inflator, set your vehicle emergency brake
and follow instructions for use as provided
WARNING: COMPRESSED AIR CAN BE DANGEROUS
— Never allow children to use this inflator
— Never leave inflator area unattended while running
— Never over-inflate items. Over-inflation could cause property damage or personal injury
— Check manufacturer’s recommended inflation pressure before starting the inflation
process
WARNING: VEHICLE EXHAUST WITHOUT PROPER VENTILATION IS EXTREMELY
DANGEROUS
— Never start and leave a vehicle running in a confined or enclosed space such as
a garage. Start and run vehicles outdoors

4
QUICK START GUIDE
NOTE: Read complete instruction manual before using inflator for the first time
1. Start vehicle
2. Plug in inflator
3. Check tire sidewall for max
tire inflation pressure
4. Select desired pressure units
by pressing “M” button and
toggle between PSI, BAR & kPA
5. Press SmartSTOP™button
to activate Countdown Timer
AND Auto-Stop features
6. Select desired tire pressure by
pressing “+” or “–” buttons
7. Attach air hose to tire valve stem
8. Start inflator
9. Inflator will automatically shut
off when target set pressure has
been reached

Inflator & Work Light
Power Button
Power Cord
Wraps Around
Base For Storage
Inflation
Accessories
Included
10 Foot 12 Volt
Power Cord
with replaceable fuse
SmartSTOP™Back-Lit
Digital Gauge
with Auto Shut-off and
Countdown Timer
Rubber Feet
for noise and vibration suppression
Work Light
48" Air Hose
8
8
0
8
8
8
53 4
03
SmartSTOP™
SmartSTOP™
On Icon
SmartSTOP™
On/Off Button
Countdown Timer
On Icon
Mode Button
Tire Pressure
Unit Selector
(PSI, BAR or kPA)
Hold Button to Reset
Pressure Sensor
Target Pressure
Set Icon
Pressure Down
Set Button
Pressure Up
Set Button
Pressure Unit
Display
Pressure Reading Display
Countdown/Settings Display
50 2
0 K
‐‐‐
TES
I‐E
Pressure Set Display
Error Message Display 1
(See trouble shooting on page 7)
2‐E
Time Calculation Mode Display
Target Pressure Reached Display
Time Countdown Display
Error Message Display 2
(See trouble shooting on page 7)
PRODUCT ILLUSTRATION
SmartSTOP™ILLUSTRATION
5

6
INFLATOR OPERATION
INFLATING TIRES
1. Make certain the inflator power button is in the off position.
2. Set emergency brake and start vehicle engine.
3. Insert the 12 Volt power plug into the vehicle’s 12 Volt DC power outlet.
4. Check manufacturer’s recommended tire pressure specifications indicated on the tire sidewall.
TO ACTIVATE SmartSTOP™FEATURE:
1. Choose the desired pressure unit (PSI, BAR, or kPA) by pressing the “M” button.
2. Press SmartSTOP™button to activate countdown timer and auto shut-off.
The SmartSTOP™, countdown timer hour glass and target set icons and “SET” will be
displayed when the SmartSTOP™ feature is active. The countdown timer and auto shut-off
operate together. Both are on or both are off.
3. Set the desired auto shut-off pressure by pressing the “+” or “–” buttons while the “SET” screen
is displayed. The display will return to current tire pressure display a few seconds after entering
the target pressure.
4. Attach air hose nozzle to vehicle tire valve stem by threading the nozzle onto the stem clockwise
until secure.
NOTE: When the nozzle is connected correctly, wait 5-7 seconds and the gauge will indicate the
current tire pressure. The pressure gauge has a built-in memory and will default to the last tire
pressure set in the pressure gauge display of the inflator.
5. Turn on inflator power button. If active, the SmartSTOP™feature will go into the “time remaining
to fill tire” calculation mode with the hour glass flipping and “- - -” being displayed. The
remaining time to fill tire will appear in minutes and seconds above the tire pressure reading and
will countdown to zero as tire reaches the target set pressure. “OK” will be displayed once the
target set pressure has been reached and the inflator will automatically shut off.
NOTE: The tire will be filling during the calculation mode.
TO DEACTIVATE SmartSTOP™FEATURE AND RETURN TO STANDARD INFLATION MODE:
1. Press SmartSTOP™button to deactivate the countdown timer and auto shut-off. The
SmartSTOP™, countdown timer hour glass and target set icons will be turned off when the
SmartSTOP™feature is inactive.
2. To stop inflator before reaching the pre-set auto shut-off pressure, turn inflator power switch to
the off position.
NOTE: If “E–1” is displayed – Error message 1, see trouble shooting on page 7.
If “E–2” is displayed – Error message 2, see trouble shooting on page 7.
ADDITIONAL NOTE: The pressure gauge on the inflator is for reference only and is therefore not
binding for exact values. While inflating, the gauge is a measurement of the fluctuating pressure
between the tire and the high pressure hose. To reduce the risk of over-inflation, use a reliable
pressure gauge after inflation before driving a vehicle inflated with the inflator.
INFLATING SPORTS BALLS OR OTHER HIGH PRESSURE SMALL INFLATABLES
1. Follow same tire inflation procedure sequence with these additional instructions.
2. Select one of the small adapter needles provided in the storage compartment and attach the
adapter needle to the air hose nozzle by turning the adapter needle clockwise.
NOTE: When inflating items requiring 10 PSI or less, inflate in short bursts and check by feel or by a
reliable measuring device to determine accurate pressure.

7
MAINTENANCE
TROUBLE SHOOTING
THE INFLATOR FAILS TO RUN WITH THE INFLATOR POWER BUTTON TURNED ON OR DIGITAL
PRESSURE GAUGE DOES NOT ILLUMINATE:
�Check that the plug is fully inserted into 12 Volt DC power outlet
�Your vehicle may require the ignition be turned to the accessory position for the power outlet to
have power. The inflator should be used with the vehicle running
�Check to see if the fuse in the 12 Volt power plug has blown. See fuse replacement instructions
in the maintenance section
INFLATOR FAILS TO STOP AT THE AUTO SHUT-OFF PRE-SET PRESSURE:
�Check to make sure auto shut-off pressure settings are being set correctly
�Check that the correct pre-set pressure has been set
�Check that the SmartSTOP™ feature is active
12 VOLT POWER CORD GETS HOT:
�Make certain power cord is not coiled up or in a knot or damaged
PRESSURE GAUGE APPEARS TO READ INCORRECTLY OR IS UNREADABLE:
�Make certain when you attach the air hose nozzle to the tire stem that the gauge is reading the
current tire pressure before turning on the inflator switch
�Wait 5-7 seconds for gauge to display proper pressure
THE INFLATOR IS RUNNING BUT THE TIRE IS NOT INFLATING:
�Turn off the inflator and check that the air hose nozzle is securely attached to the tire valve stem
�Check if tire has too large of leak to fill
DIGITAL DISPLAY SHOWS ERROR MESSAGE:
�E-1 error message will be displayed if the tire has too large of a leak that the tire cannot be filled
or if inflator is running but not attached to tire. Recheck puncture is well sealed and air hose
nozzle is connected to vehicle tire valve stem
�E-2 error message will be displayed if the inflator reaches above 150 PSI (over pressure shut-down)
When E-2 appears, press inflator power button. Inflator should be off. See digital gauge reset.
DIGITAL DISPLAY SHOWS “0” WHEN TIRE HAS PRESSURE:
�Perform DIGITAL GAUGE RESET below
DIGITAL GAUGE RESET:
�Make certain the inflator has power and the inflator pump is OFF. Make certain the air hose
nozzle is connected to the tire stem. Let the gauge adjust for a few seconds. Press and hold the
“M” button for a few seconds to reset the pressure sensor. Remove the air hose from the tire
and reattach air hose to tire and proceed with normal inflator operation.
NOTE: The inflator will not reset if the pump is running
1. Your SmartSTOP™inflator has a replaceable fuse providing maximum protection for the inflator
and/or your vehicle.
2. Regularly check inflator air hose, 12 Volt cord and adapters for damage.
Fuse: Replace with fast blow 15 AMP, 250V, " x ¾" (5mm x 20mm), glass fuse only.
16
Turn tip counterclockwise to
unlock Fuse Adapter Body
Adapter Body
12 Volt Adapter Fuse Replacement

0262 �Rev C 1/19
CONTACT INFORMATION
Hopkins Manufacturing Corporation
428 Peyton St., Emporia, KS 66801
1-800-524-1458
www.MonkeyGripTireSafety.com
Patents: HopkinsMfg.com/IP
8
WARRANTY
LIFETIME WARRANTY
Hopkins Manufacturing Corporation warrants this product will be free from defects in material and
workmanship. Hopkins Manufacturing Corporation, at its option, will repair or replace this product or
any component of the product found to be defective. Replacement will be made with a new or
remanufactured product or component. In the event the product is no longer available, replacement
may be made with a similar product.
This warranty is valid for the original retail purchaser and is not transferable. Keep the original sales
receipt. Proof of purchase is required to obtain warranty coverage.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover parts that are not genuine Hopkins Manufacturing Corporation parts,
or damage resulting from any of the following: negligent use or misuse of the product; use on
improper voltage or current; commercial use of the product; use other than the operating
instructions, disassembly, repair or alteration by anyone other than Hopkins Manufacturing
Corporation. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and
tornadoes.
Hopkins Manufacturing Corporation shall not be liable for any incidental or consequential damages
caused by the breach of any express or implied warranty or conditions, except to the extent
prohibited by applicable law, any implied warranty of merchantability or fitness for a particular
purpose is limited to the above warranty or conditions. Some states, provinces, or jurisdictions do
not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts so the above limitations or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights that vary from state to
state or province to province.
The costs of transporting the product to Hopkins Manufacturing Corporation for warranty service are
the responsibility of the purchaser.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE
If you have any questions regarding this warranty please contact us below: