Monogram UX12BS36PSS User manual

INSTALLATION
INSTRUCTIONS
30”, 36” and 48”
Dual Fuel Professional Ranges
ENGLISH/FRANÇAIS/ESPAÑOL.
MONOGRAM.COM

231-2000667 Rev. 1
Safety Information
READ AND SAVE THESE INSTRUCTIONS
IN THE COMMONWEALTH OF MASSACHUSETTS
■This product must be installed by a licensed plumber
or gas fitter.
■ Whenusingballtypegasshut-offvalves,theyshall
betheT-handletype.
■ Aflexiblegasconnector,whenused,mustnotexceed
5 feet.
WARNING FIRE OR EXPLOSION HAZARD
Iftheinformationinthismanualisnotfollowedexactly,
afireorexplosionmayresultcausingpropertydamage,
personal injury or death.
Installation must be performed by a qualified installer.
Read these instructions completely and carefully.
Installationofthisrangemustconformwithlocalcodes,
orintheabsenceoflocalcodes,withtheNational
FuelGasCode,ANSIZ223.1/NFPA.54,latestedition.
InCanada,installationmustconformwiththecurrent
NaturalGasInstallationCode,CAN/CGA-B149.1or
thecurrentPropane(LP)InstallationCode,CAN/CGA-
B149.2,andwithlocalcodeswhereapplicable.This
rangehasbeendesign-certifiedbyCSAInternational
accordingtoANSIZ21.1,latesteditionandCanadian
GasAssociationaccordingtoCAN/CGA-1.1latestedition.
Wheninstallingagasappliancetheuseof
oldflexibleconnectorscancausegasleaksand
personalinjury.AlwaysuseaNEWflexibleconnector.
Leaktestingoftheapplianceshallbeconducted
according to the manufacturer instructions.
The range must be electrically grounded in accordance
withlocalcodesor,intheabsenceoflocalcodes,in
accordancewiththeNationalElectricalCode(ANSI/
NFPA70,latestedition).InCanada,electricalgrounding
mustbeinaccordancewiththecurrentCSAC22.1
CanadianElectricalCodePart1and/orlocalcodes.See
ElectricalConnectionsinthissection.
Donotinstallthisproductwithanaircurtainhoodor
otherrangehoodthatoperatesbyblowingairdownon
thecooktop.Thisairflowmayinterferewithoperationof
thegasburnersresultinginfireorexplosionhazard.
FOR YOUR SAFETY
Ifyoudidnotreceiveananti-tipbracketwithyour
purchase,call1.800.626.8774toreceiveoneatno
cost.(InCanada,call1.800.561.3344.)Forinstallation
instructionsofthebracket,visit:GEAppliances.com.
(InCanada,GEAppliances.ca.)
WARNING Beforebeginningtheinstallation,
switchpoweroffatservicepanelandlocktheservice
disconnectingmeanstopreventpowerfrombeing
switchedonaccidentally.Whentheservicedisconnecting
meanscannotbelocked,securelyfastenaprominent
warningdevice,suchasatag,totheservicepanel.
Have a question or need assistance with your appliance? Try the Monogram website 24 hours a day, any day of
the year! You can also shop for more great Monogram products and take advantage of all our on-line support
services designed for your convenience. In the US: monogram.com
• A child or adult can tip the range and be killed.
• Install the anti-tip bracket to the wall or floor.
• Engage the range to the anti-tip bracket by sliding the
range back such that the foot is engaged.
• Re-engage the anti-tip bracket if the range is moved.
• Failure to do so can result in death or serious burns
to children or adults.
Tip-Over Hazard
WARNING
Anti-TipBracket
Kit Included
RearView

31-2000667 Rev. 13
Safety Information
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
■IMPORTANT —Savetheseinstructions
for local inspector’s use.
■IMPORTANT —Observeallgoverning
codes and ordinances.
■IMPORTANT —Removeallpacking
materialandliteraturefromovenbeforeconnecting
gas and electrical supply to range.
■IMPORTANT —Toavoiddamageto
yourcabinets,checkwithyourbuilderorcabinet
suppliertomakesurethatthematerialsusedwill
notdiscolor,delaminateorsustainotherdamage.
Thisovenhasbeendesignedinaccordancewith
therequirementsofULandCSAInternationaland
complieswiththemaximumallowablewoodcabinet
temperaturesof194°F(90°C).
■Note to Installer — Besuretoleavethese
instructionswiththeconsumer.
■Note to Consumer —Keeptheseinstructionswith
yourOwner’sManualforfuturereference.
■Servicer —Theelectricaldiagramisinanenvelope
attachedtothebackoftherange.
■Properinstallationistheresponsibilityofthe
installer.
■Productfailureduetoimproperinstallationisnot
coveredunderwarranty.
■Beforeinstallingyourrangeonlinoleumoranyother
syntheticfloorcovering,makesurethefloorcovering
canwithstand180°Fwithoutshrinking,warpingor
discoloring.Donotinstalltherangeovercarpeting
unlessasheetof1/4”thickplywoodorsimilar
insulatorisplacedbetweentherangeandcarpeting.
■ForMonogramPartsandAccessories,visitour
websiteatmonogram.com/ownership/parts/
■Ifyoureceivedadamagedrange,youshould
contact your dealer.
IF SOLD OUTSIDE THE U.S. AND
CANADA
WARNING Ifyouwishtousethisproductwith
LiquefiedPetroleum(LP)gascontaininggreater
than10%butane,youmustpurchasethebutane
conversionkit#ZXBUPR01.Toorder,pleasecall
1.888.664.8403or1.787.276.4051.Failuretodoso
mayresultincarbonmonoxideorfirehazard.
VENT HOOD COMBINATIONS
Asuitableoverheadventhoodisrequiredformodels
withagrillandisrecommendedforallothermodels.
Duetothehighheatcapacityofthisunit,particular
attentionshouldbepaidtothehoodandductwork
installation to assure it meets local building codes.
Clearancestohorizontalsurfacesabovetherange,
measuredtothecookingsurfacearebelow.Failureto
complymayresultinfirehazard.
■Installationswithoutahoodrequire48”minimum
tocombustiblesexceptmodelZDP484wherea
suitableventhoodisrequired.
■Acustomhoodinstallationwithexposedhorizontal
combustiblessurfacesmusthaveanAuto-Onfeature.
■Forotherinstallationswithahood,refertohood
installation instructions for specific hood clearances.
CAUTION Theserangesweighupto700
pounds.Somedisassemblywillreducetheweight
considerably.Duetotheweightandsizeoftherange
andtoreducetheriskofpersonalinjuryordamageto
theproduct:
TWOPEOPLEAREREQUIREDFORPROPER
INSTALLATIONOF36”AND30”RANGES.
THREEPEOPLEAREREQUIREDFORPROPER
INSTALLATIONOF48”RANGES.
RatingLabelLocation RatingLabelLocation

431-2000667 Rev. 1
Contents
CONTENTS
Safety Information....................................................... 2
Design Information
ProductDimensionsandClearances............................ 5
Installation Information
WB28K10553HighAltitudeKit ..................................... 9
MaterialsProvided......................................................... 9
MaterialsRequired(notprovided)................................. 9
Tools Required.............................................................. 9
Installation
RemovePackaging ..................................................... 10
MovetheRangeIndoors............................................. 11
InstallAnti-TipDevice.................................................. 12
ConvertingtoPropane(LP)GasorConverting
BacktoNaturalGasFromPropane(LP)................. 13
GasSupply.................................................................. 13
ElectricalConnections................................................. 14
RollRangeintoPosition.............................................. 15
LeveltheRange .......................................................... 16
ReplaceOvenDoor(s)................................................. 16
CheckBurners............................................................. 17
CheckSurfaceBurners ............................................... 17
FinalizeInstallation...................................................... 17
WhenAllHookupsAreCompleted.............................. 17
Accessory Installation
Toekick(included) ....................................................... 18
UX12BS36PSS, UX12BS48PSS Accessory Installation
Optional Accessories—12” High Backsplash
ToolsandMaterialsRequired ..................................... 19
Install12”Backsplash ................................................. 19
UXADBS36PSS, UXADBS48PSS Accessory Installation
Accessories—30” To 36” Adjustable Backsplash
ToolsandMaterialsRequired ..................................... 20
InstalltheWallSupportPanels ................................... 20
InstallCoverPanels .................................................... 21

31-2000667 Rev. 15
Design Information
PRODUCT DIMENSIONS AND CLEARANCES
48” Range Models
UniversalUtilityLocations
3”Min. 3”Min.
Island
Cutout
TopView
2-1/2”Min.
WARNING
Asuitableoverheadvent
hoodisrequiredformodelZDP484.Installations
withoutahoodrequire48”minimumto
combustibles.Acustomhoodinstallation
withexposedhorizontalcombustiblesurfaces
musthaveanAuto-Onfeature.Refertohood
installation instructions for specific hood
clearances.
Thesurfaceoftheentirebackwallabovethe
rangeandbelowthehoodmustbecovered
withanon-combustiblematerialsuchasmetal,
ceramictile,brick,marbleorotherstone.
CAUTION Topreventdraftsfrom
affectingburneroperation,sealallopenings
in floor under appliance and behind appliance
wall.
**AsdefinedintheNationalFuelGasCode(ANSI
Z223.1/CSAB149.1,CurrentEdition).Clearancesfrom
non-combustiblematerialsarenotpartoftheANSI
Z21.1/CSA1.1scopeandarenotcertifiedbyCSA.
Clearanceslessthan12”mustbeapprovedbylocal
codesand/ortheauthorityhavingjurisdiction.
ADDITIONAL CLEARANCES:
Allow12”minimumclearancetoanadjacentwallon
each side.
Workingareasadjacenttotherangetopshouldhave
18”minimumclearancebetweencountertopandthe
bottomofthewallcabinet.
Forislandinstallation,maintain2-1/2in.minimumfrom
cutouttobackedgeofcountertopand3in.minimum
fromcutouttosideedgesofcountertop(seetopview).
16”
Max.
48”Min.
12”Minimum
toAdjacentWall
Non-
Combustible
Material**
48”Minimum
Vent Hood
Required for
ModelZDP484
18”
Min.
12”
Minimum
EachSide
Back
47-7/8”
Width
1”
Countertop
toCooking
Surface
35-1/4”to36-3/4”
Height to trim.
Trim to be flush
or higher than
countertop.
28-1/2”Depth
to Front of Door
293/8”Depth
to Front of
Bullnose
Toekick/
leg Height
3-1/4”
to4-3/4”
48”
8”
14”
2”
16”
Gas/
Electric Electric
6-1/2”
2”
60”forZDP486
minimum to
combustibles

631-2000667 Rev. 1
Design Information
PRODUCT DIMENSIONS AND CLEARANCES
36” Range Models
16”
Max.
36”Min.
36”
Minimum 12”Minimum
toAdjacentWall
Non-
Combustible
Material**
48”Minimum
to Combustibles
18”
Min.
3”Min. 3”Min.
Island
Cutout
TopView
2-1/2”Min.
WARNING
Installationswithouta
hoodrequire48”minimumtocombustibles.
Acustomhoodinstallationwithexposed
horizontalcombustiblesurfacesmusthave
anAuto-Onfeature.Refertohoodinstallation
instructions for specific hood clearances.
Thesurfaceoftheentirebackwallabove
therangeandbelowthehoodmustbe
coveredwithanon-combustiblematerial
suchasmetal,ceramictile,brick,marbleor
other stone.
CAUTION Topreventdraftsfrom
affectingburneroperation,sealallopenings
in floor under appliance and behind
appliancewall.
**AsdefinedintheNationalFuelGasCode(ANSI
Z223.1/CSAB149.1,CurrentEdition).Clearances
fromnon-combustiblematerialsarenotpartofthe
ANSIZ21.1/CSA1.1scopeandarenotcertifiedby
CSA.Clearanceslessthan12”mustbeapprovedby
localcodesand/ortheauthorityhavingjurisdiction.
ADDITIONAL CLEARANCES:
Allow12”minimumclearancetoanadjacentwallon
each side.
Workingareasadjacenttotherangetopshouldhave
18”minimumclearancebetweencountertopandthe
bottomofthewallcabinet.
Forislandinstallation,maintain2-1/2in.minimumfrom
cutouttobackedgeofcountertopand3in.minimum
fromcutouttosideedgesofcountertop(seetopview).
12”
Minimum
EachSide
Back
UniversalUtilityLocations
35-7/8”
Width
1” Countertop
toCooking
Surface
35-1/4”to36-3/4”
Height to trim.
Trim to be flush
or higher than
countertop.
293/8”Depthto
FrontofBullnose
28-1/2”Depth
to Front of Door
Toekick/
leg Height
3-1/4”
to4-3/4”
36”
4-5/8”
13-3/8”
2”
11-3/8”
Gas/
Electric Electric
6-1/2”
2”

31-2000667 Rev. 17
Design Information
PRODUCT DIMENSIONS AND CLEARANCES
30” Wide Range Models
3”Min. 3”Min.
Island
Cutout
TopView
2-1/2”Min.
WARNING
Installationswithouta
hoodrequire48”minimumtocombustibles.
Acustomhoodinstallationwithexposed
horizontalcombustiblesurfacesmusthave
anAuto-Onfeature.Refertohoodinstallation
instructions for specific hood clearances.
Thesurfaceoftheentirebackwallabove
therangeandbelowthehoodmustbe
coveredwithanon-combustiblematerial
suchasmetal,ceramictile,brick,marbleor
other stone.
CAUTION Topreventdraftsfrom
affectingburneroperation,sealallopenings
in floor under appliance and behind
appliancewall.
**AsdefinedintheNationalFuelGasCode(ANSI
Z223.1/CSAB149.1,CurrentEdition).Clearances
fromnon-combustiblematerialsarenotpartofthe
ANSIZ21.1/CSA1.1scopeandarenotcertifiedby
CSA.Clearanceslessthan12”mustbeapprovedby
localcodesand/ortheauthorityhavingjurisdiction.
ADDITIONAL CLEARANCES:
Allow12”minimumclearancetoanadjacentwallon
each side.
Workingareasadjacenttotherangetopshouldhave
18”minimumclearancebetweencountertopandthe
bottomofthewallcabinet.
Forislandinstallation,maintain2-1/2in.minimumfrom
cutouttobackedgeofcountertopand3in.minimum
fromcutouttosideedgesofcountertop(seetopview).
Back
16”
Max.
30”Min.
30”
Minimum 12”Minimum
toAdjacentWall
Non-
Combustible
Material**
48”Minimum
to Combustibles
18”
Min.
12”
Minimum
Each
Side
UniversalUtilityLocations
28-1/2”Depthto
Front of Door
29-7/8”Width
1”
Countertop
toCooking
Surface
293/8”Depthto
FrontofBullnose
35-1/4”to36-3/4”
Height to trim. Trim
to be flush or higher
than countertop.
Toekick/
leg Height
3-1/4”
to4-3/4”
30”
4-5/8”
2”
7-3/8”11-3/8”
Gas/
Electric Electric
6-1/2”
2”

831-2000667 Rev. 1
Design Information
PRODUCT DIMENSIONS AND CLEARANCES
48”, 36” and 30” Range Models
12”Min.tocombustiblesor0”
toanon-combustiblematerial
abovethecookingsurface**
48-1/4”
WithOvenDoorOpen
31-1/8”
To Front of Handle
35-1/4”
to
36-3/4”
30-36”
12”
(36”models
only)
13/16”
10-1/2”
29-3/8”
ToFrontEdge
28-1/2”
To Front of Door
Optional
Backsplash
Accessories
0”Clearance
toabackor
sidewallbelow
thecooking
surface
7”ControlPanel
Height
1”
**AsdefinedintheNationalFuelGasCode(ANSIZ223.1/CSAB149.1,CurrentEdition).Clearancesfrom
non-combustiblematerialsarenotpartoftheANSIZ21.1/CSA1.1scopeandarenotcertifiedbyCSA.
Clearanceslessthan12”mustbeapprovedbylocalcodesand/ortheauthorityhavingjurisdiction.
WARNING The12”highstainlesssteelbacksplashaccessorymustbe
installedincombinationwithacustomnon-combustiblebacksplash.
Thefinishedbacksplashmustcovertheentirebackwalluptothebottomofahood,
orwhenthereisnohood,48”tocombustibles.
(12”highstainlesssteelbacksplashaccessoryisonlyavailableforthe36”model)

31-2000667 Rev. 19
Installation Information
TOOLS REQUIRED
MATERIALS REQUIRED (not provided)
INSTALLATION AT HIGH ALTITUDE
Over6000ft,productconfiguredfornaturalgasor
propanerequiresinstallationofkit(WB28X39726
fornaturalgasandWB28X39727forpropanegas).
Followtheinstructionsincludedwiththekit.
MATERIALS PROVIDED
OvenRack
Lubricant Runners
(toprotect
flooring)
1/2”Pipe
Elbow
Anti-Tip
Bracket,Brace
andScrews
LevelingLeg
Wrench
AdjustableWrench
1/4”DriverorWrench
SafetyGlasses
Drill and
AppropriateBits
MeasuringTape
Phillips#2Screwdriver
SaberSaw
Carpenter’sSquare
Level HandTruck
Shut-OffValve
Shut-OffValve
PipeFittings
5-footmaximumlength,5/8”O.D.CSA-
approvedflexiblemetalgassupply
NOTE:Purchasenewflexibleline;donot
usepreviouslyusedflexiblegasline.
PipeThread
Sealant

10 31-2000667 Rev. 1
Installation
1REMOVE PACKAGING
CAUTION Standclear.Theendsofthecutmetal
bandingmaysnaptowardyou.
■Cutthemetalbanding.Liftthecartonstraightup.
■Locatethetworunnerstripsfromthetopofthe
packaging.Thesestripswillbeusedtoprotectthe
kitchenfloorduringinstallation.
■Removecornerposts.Disposeofpackagingmaterials.
■Removegrill/griddlecovers,grillgrateandburnergrates.
■Liftoutcast-irongriddlefluecover,greasetroughs
and pads.
■Cutthetiesholdingthegrillgratetothegrillframe.
■Liftoffburnercapsandremovefoampad,thenliftoff
burnerheadsandremovefoampad.
■Openovendoor(s)andremovepackaging.Remove
shelfholdingbroilerpan,tape,literaturepackage,shelf
lubricant and probe.
CAUTION Doorsandpassagewaysleadingtothe
installationlocationrequireatleast32”opening.Ifthe
openingislessthan32”,theovendoor(s)andcontrol
knobsmustberemoved.
REMOVETHEOVENDOOR(S)ONLYIFNECESSARY
tomovetherangethroughthedoorways.Toprevent
damagetothesidesoftherange,itwillbenecessaryto
padthecornersbeneaththestrapsonthehand-truck.
To remove the oven door(s):
■Toremovetheovendoor(s):
■Fullyopenthedoor.
■Eachhingehasahingelock.Pullthehinge.
■Firmlygraspthedooratthetopsides.
■Closethedoortothenear-verticalposition.
■Liftthedoorupandpullstraightout.
RemoveFoamPads
Hinge
Lock
GriddleFlueCover
Grease Troughs
Ties
Lockupandawayfromthefrontframe.

31-2000667 Rev. 111
Installation
2MOVE THE RANGE INDOORS
1. Tilttherangeforwardontheskid.
2. Liftthetoekickoutofthefoambase.
3. Drivethebladeofthehand-truckbeneaththefoam
block.
IMPORTANT:Donotremovethebasefoamblockwhile
thehand-truckisinuse.Placethehand-truckblade
underneaththebasefoamblockandtransporttherange
to the final location.
4. Attachthehand-truckstrapsaroundtheunit.
IMPORTANT:Placethehand-truckstrapsbelowthe
ovendoorhandles.Toavoiddamagingthesidepanels,
placeapadbetweenthehand-truckandtherange.
5. Tilttherangetolowerthehand-truckwheelsoffthe
skid.
6. Placetheappliancerunnersonthefloorattheleft
and right sides in front of the opening.
IMPORTANT:Therunnersprovideasurfacefor
rollingtherangeintothefinalpositionandwillprotect
thefloorfinish.Therunnersmustberemovedbefore
levelingtherange.
7. Movetherangeindoors.Positiontherangeinfrontof
theinstallationlocation,ontotherunners.
Toekick
Toekick
InsertBladeUnder
theFoamBlock
Youmayneedtoremove
thefrontofthefoamblock
tofitthroughthedoorway.
Hand-Truck
StrapsBelow
OvenDoor
Handles
Range
Opening
Runners
for Rolling
the Range
into
Position

12 31-2000667 Rev. 1
Installation
3INSTALL ANTI-TIP DEVICE
Toreducetheriskoftippingtherange,therangemust
besecuredbyaproperlyinstalledanti-tipbracket.See
installationinstructionsshippedwiththebracketfor
complete details before attempting to install.
Tocheckifthebracketisinstalledandengaged
properly,lookunderneaththerange.Theanti-tipbracket
shouldbeinsertedintotheopeningontheanti-tipbrace
ontherange.Ifthebracketarmmissesthebracetothe
leftorright,orthebracketarmisnotprotrudingthrough
thebraceopening,thebracketmustbereinstalled.
Iftherangeispulledfromthewallforanyreason,
alwaysrepeatthisproceduretoverifytherangeis
properlysecuredbytheanti-tipbracket.
Ifyourrangehasnoanti-tipbracket,call1.800.626.8774
toreceiveoneatnocost.
Iftheanti-tipdevicesuppliedwiththerangedoesnot
fitthisapplication,usetheuniversalAnti-TipDevice
WB2X7909.
ReadtheAHAMAnti-TipSafetyBrochurepackedwith
thebracket.
Anti-Tip Parts Provided
■Attachtheanti-tipbraceontothebottomoftherange
intherecessedarea.Install2hexscrews(provided)
through the brace and into the range.
NOTE:Thisanti-tipdevicemaybeinstalledonthe
opposite side of the range.
■MeasureandmarkDimensionA(seetablebelow)
fromtheleft(orright)sideoftheinstallationlocation.
Ifthecountertophasanoverhang,addthatdimension
toDimensionA.
■Placetheanti-tipbracketagainstthefloorandbackwall
atthemarkedlocation.Markscrewholesforfastening
thebrackettothewallsoleplateandthefloor.
■Drill1/8”pilotholesata20°angle.
■Securethebrackettothewalland/orfloorwithatleast
2woodscrews(provided).
For Concrete or Cement Construction:Youmustuse
appropriatefasteninghardware(notprovided).
• A child or adult can tip the range and be killed.
• Install the anti-tip bracket to the wall or floor.
• Engage the range to the anti-tip bracket by sliding the
range back such that the foot is engaged.
• Re-engage the anti-tip bracket if the range is moved.
• Failure to do so can result in death or serious burns
to children or adults.
Tip-Over Hazard
WARNING
Anti-TipBracket
Anti-TipBrace
4WoodScrews
AHAMAnti-Tip
SafetyBrochure
3HexHeadScrews(2
required,1extra)
AlternateBrace
Position
HexScrews
Anti-TipBrace
Anti-TipBracket
A
WallSolePlate
Range A
30” 5-1/16”
36” 5-1/16”
48” 8-1/4”

31-2000667 Rev. 113
Installation
4CONVERTING TO PROPANE (LP)
GAS OR CONVERTING BACK
TO NATURAL GAS FROM
PROPANE (LP)
Thisrangeleavesthefactorysetforusewithnatural
gas.Ifyouwanttoconverttopropane(LP)gas,the
conversionmustbeperformedbyaqualifiedpropane
(LP)gasinstaller.
Theconversionorifices
and instructions can
befoundonbackof
the range.
Keep these
instructions and all
orifices in case you
wanttoconvertback
to natural gas.
5GAS SUPPLY
WARNING FireHazard:Donotuseaflameto
checkforgasleaks.
WARNING ExplosionHazard:Donotexceed
25ft-lbsoftorquewhenmakinggaslineconnections.
Overtighteningmaydamagethepressureregulator
resultinginfireorexplosionhazard.
Gas Pressure Regulator
Youmustusethegaspressureregulatorsupplied
withthisrange.Forproperoperationstheinlet
pressuretotheregulatorshouldbeasfollows:
Natural Gas:
 Minimumpressure:6”ofWaterColumn
 Maximumpressure:13”ofWaterColumn
Propane (LP) Gas:
 Minimumpressure:11”ofWaterColumn
 Maximumpressure:13”ofWaterColumn
If you are not sure about the inlet pressure contact
local gas supplier.
NOTE:Agasshutoffvalveisshippedwiththisrange
and should be installed at the rear of the range near
thefloorwiththehandlefacingdownward.Thisshut-
offvalveistobeusedin
theeventthatserviceis
required. To access the
shut-offvalve,removethe
toe-kickpanelandreach
undertherange.Anoptional
1/2”elbowisprovidedfor
connection to the range gas
inlet.
5GAS SUPPLY (cont.)
Shut off the main gas supply valve before
disconnecting the old range and leave it off until
the new hook-up has been completed. Don’t
forget to relight the pilot on other gas appliances
when you turn the gas back on.
Becausehardpipingrestrictsmovementoftherange,
theuseofaCSAInternational-certifiedflexiblemetal
appliance connector is recommended unless local
codesrequireahard-pipedconnection.
Ifthehardpipingmethodisused,youmustcarefully
alignthepipe;therangecannotbemovedafterthe
connection is made.
Topreventgasleaks,putpipethreadsealanton,or
wrappipethreadtapewithTeflon*around,allmale
(external)pipethreads.
A. Installamanualshut-offvalveinthegaslineinan
easilyaccessedlocationoutsideoftherange.Make
sureeveryoneoperatingtherangeknowswhere
andhowtoshutoffthegassupplytotherange.
B. Installmale1/2”flareunionadaptertothe1/2”
NPTinternalthreadatinletoftheshut-offvalveon
therange.Useabackupwrenchontheshut-off
valvetoavoiddamage.
C. Installmale1/2”or3/4”flareunionadaptertothe
NPTinternalthreadofthehouseshut-offvalve,
takingcaretoback-uptheshut-offvalvetokeepit
from turning.
D. Connectflexiblemetalapplianceconnectortothe
adapterontherange.Positionrangetopermit
connectionatthehouseshut-offvalve.
E. Whenallconnectionshavebeenmade,makesure
all range controls are in the off position and turn
onthemaingassupplyvalve.Usealiquidleak
detectoratallgasconnectionstocheckforleaks
in the system.
Whenusingpressuresgreaterthan1/2psigto
pressuretestthegassupplysystemoftheresidence,
disconnecttherangeandindividualshut-offvalve
fromthegassupplypiping.Whenusingpressures
of1/2psigorlesstopressuretestthegassupply
system,simplyisolatetherangefromthegassupply
systembyclosingtheindividualshut-offvalve.
Whencheckingforproperoperationoftheregulator,
theinletpressuremustbeatleast1”greaterthanthe
operating(manifold)pressureasgivenonratinglabel
of product.
*Teflon:RegisteredtrademarkofDuPont
Gas Inlet
Oven
Regulator
CooktopRegulator
Propane
ConversionKit

14 31-2000667 Rev. 1
Installation
6ELECTRICAL CONNECTIONS
WARNING This appliance must be properly
grounded.
WARNING Allnewconstructions,mobile
homes,recreationalvehiclesandinstallationswhere
localcodesdonotallowgroundingthroughneutral,
requirea4-conductorUL-listedrangecord.
WARNING Topreventfireorshock,donotuse
anextensioncordwiththisappliance.
WARNING Topreventshock,removehouse
fuseoropencircuitbreakerbeforebeginning
installation.
Werecommendyouhavetheelectricalwiringand
hookupofyourrangeconnectedbyaqualified
electrician.Afterinstallation,havetheelectricianshow
youhowtodisconnectpowerfromtherange.
Youmustuseasingle-phase,120/208VACor
120/240VAC,60hertzelectricalsystem.Ifyou
connecttoaluminumwiring,properlyinstalled
connectorsapprovedforusewithaluminumwiring
must be used.
EffectiveJanuary1,1996,theNationalElectrical
Coderequiresthatnewconstruction(notexisting)
utilizea4-conductorconnectiontoanelectricrange.
Wheninstallinganelectricrangeinnewconstruction,
mobilehome,recreationalvehicle,oranareawhere
local codes prohibit grounding through the neutral
conductor,refertothesectiononfour-conductor
branch circuit connections.
Checkwithyourlocalutilitiesforelectricalcodeswhich
applyinyourarea.Failuretowireyourovenaccording
togoverningcodescouldresultinahazardous
condition.Iftherearenolocalcodes,yourovenmust
bewiredandfusedtomeettheNationalElectrical
Code,NFPANo.70–latestedition,availablefromthe
NationalFireProtectionAssociation.
Thisappliancemustbesuppliedwiththeproper
voltageandfrequency,andconnectedtoanindividual,
properlygrounded,(50ampfor48”ranges,30amp
for36”and30”ranges)branch circuit protected by a
circuitbreakerortime-delayfuse.
Useonlya3-conductorora4-conductorUL-listed
rangecord.Thesecordsmaybeprovidedwithring
terminalsonwireandastrainreliefdevice.
6
ELECTRICAL CONNECTIONS (Cont.)
Arangecordratedat40ampswith125/250minimum
voltrangeisrequired.A50amprangecordisnot
recommendedbutifused,itshouldbemarkedfor
usewithnominal13⁄8”diameterconnectionopenings.
Careshouldbetakentocenterthecableandstrain
reliefwithintheknockoutholetokeeptheedgefrom
damaging the cable.
NOTE:Useofautomatic,wirelessorwiredexternal
switchesthatshutoffpowertotheappliances,arenot
recommended for this product.
7
4-WIRE POWER CORD
INSTALLATION
NOTE:A4-wirecordisconnectedtotherangeatthe
factory.Usethefollowingstepstochangeanexisting
installationfroma3-wirecordbacktoa4-wirecord.
WARNING Theneutralwireofthesupplycircuit
must be connected to the neutral terminal located
inthelowercenteroftheterminalblock.Thepower
leadsmustbeconnectedtothelowerleftandthe
lowerrightterminalsoftheterminalblock.The4th
grounding lead must be connected to the frame of the
rangewiththegroundplateandthegroundscrew.
■Removethe3lowerterminalscrewsfromthe
terminalblock.Removethegroundscrewand
ground plate and retain them.
■Removethegroundstrap.
DO NOT DISCARD THE GROUND STRAP OR
ANY SCREWS.
■Inserttheonegroundscrewintothepowercord
groundwireterminalring,throughthegroundplate
and into the frame of the range.
The access
plate is on
thebackof
the range.

31-2000667 Rev. 115
9ROLL RANGE INTO POSITION
WARNING TheAnti-TipBracketmustbe
properlyinstalledtopreventtippingoftherange.
Failure to do so can cause serious damage or injury.
■Checktobesuretheappliancerunnersare
beneaththewheels.
■Therangeisshippedwiththewheelsinthedown
position.Carefullyrolltherangeintoposition,being
carefulnottoentangleorpinchthepowercordand
flexiblegastubing.
■Removetherunnersbeneaththerange.
BesureAnti-Tip
Bracketisengaged
withthebraceon
the range.
Installation
7
4-WIRE POWER CORD
INSTALLATION (Cont.)
■Insertthe3terminalscrews(removedearlier)
througheachpowercordterminalringandintothe
lowerterminalsoftheterminalblock.Becertainthat
thecenterwire(white/neutral)isconnectedtothe
centerlowerpositionoftheterminalblock.Tighten
screwssecurelyintotheterminalblock.
8
3-WIRE POWER CORD
INSTALLATION
NOTE:A4-wirecordisconnectedtotherangeatthe
factory.Usethefollowingstepstochangetherange
toa3-wirecord.
WARNING Theneutralorgroundwireofthe
powercordmustbeconnectedtotheneutralterminal
locatedinthecenteroftheterminalblock.Thepower
leadsmustbeconnectedtothelowerleftandthe
lowerrightterminalsoftheterminalblock.
■Removethegroundstrap(locatedattherightside
oftheterminalblock)andconnectbetweenthe
centerlowerportionoftheterminalblocktothe
frame of the range.
8
3-WIRE POWER CORD
INSTALLATION (Cont.)
■Removethe3lowerterminalscrewsfromthe
terminalblock.Insertthe3terminalscrewsthrough
eachpowercordterminalringandintothelower
terminalsoftheterminalblock.Becertainthat
thecenterwire(white/neutral)isconnectedtothe
centerlowerpositionoftheterminalblock.Tighten
screwssecurelyintotheterminalblock.
DO NOT REMOVE THE GROUND STRAP
CONNECTION.
Before
After
Terminal
Block
Terminal
Block
Neutral
Terminal
NeutralTerminal
GroundStrap
GroundPlate
(groundingto
range)
Ground
Screw
GroundStrap
or
Ground
Strap
TerminalBlock
(appearancemayvary)
Neutral
Terminal
PowerCord
Ground
Plate

16 31-2000667 Rev. 1
Installation
10 LEVEL THE RANGE
WARNING
Therangemustbelevelandbe
supportedbythelegs—notthewheels.Therangecould
moveifthewheelsmakecontactwiththefloor.Besure
alllegsmakecontactwiththefloorinanyinstallation.
■Alllegsmustbeleveledaftertheproductisinstalled.
■Checktobesuretheadjoiningcabinets/countertops
arelevel,fronttobackandlefttorightacrossthe
opening of the range.
■ Measurethedistancefromthefloortothetopofthe
countertop in the left and right rear corners.
■ Adjusttheheightoftherangetocountertopheight
or higher.
IMPORTANT:Thisrangeshouldalwaysbeinstalled
atcountertopheightorhigher.DONOTINSTALLTHE
RANGELOWERTHANADJACENTCOUNTERTOP
HEIGHT.Therangemustbesupportedbyall4legs,
regardless of countertop height.
FRONT LEG ADJUSTMENT
■Alevelinglegwrenchissupplied.Reachunderthe
frontoftherangeneartherightleg.Locateand
removeathumbscrew,thenslidewrenchoutof
the slot.
■Slidefrontcylindersuptoaccessfrontlevelinglegs.
Becarefulnottodamagecylinder.
■Usethesuppliedwrenchtoadjustthefrontleveling
legs.Turnclockwisetoextendthelegstoliftand
stabilizetherange.Turncounterclockwisetoretract
thelegsandallowtherangetorestonitsrollers.
■Besuretoreturnthewrenchtoitsstorageslotfor
future use.
10 LEVEL THE RANGE (cont.)
REAR LEG ADJUSTMENT
WARNING Toreducetheriskoffireorelectric
shock,alwaysreplacethespillplugsintheleveling
rod holes.
■ Removetwoscrewsfromrearventtrim.Slidevent
trimforward,thenliftuptoremove.
■ Removethe2spillplugstolocatetherearleg
extensionlevelingrods.Usea1/4”driverorsocket
wrenchtoadjusttheleftorrightrearlegs.
■ Findthetworearlegextensionrods.Usea1/4”driver
orwrenchtoadjusttheleftorrightrearlegs.
■ Replace the 2 spill plugs and then replace the rear
venttrimusingtheoriginalscrews.
Slideleg
cylinder up.
ThumbScrew 11 REPLACE OVEN DOOR(S)
Skip this step if oven doors are in place.
IMPORTANT: Do not lift the door by the handle.
To replace the oven doors:
■ Firmly grasp the door at the top sides. This is critical.
■Approachtherangewiththedoorangledina
verticalposition.
■Guidethehingesintotheslots.
■Pushthedoorinfirmlywhileopening.
■Onceinposition,openthedoorcompletely.Push
thehingelocksbackintowardthefrontframe.
CAUTION
Takecarewhenreplacingtheoven
doors. If the hinge latch
isnotsecurelylocked,
thehingemaysnapback
and separate. If the hinge
separates,youmustapply
pressure(possiblywith
yourfoot)topressitback
together and then engage
the hinge latch.
SpillPlugs RearLeg
Extension
Rods

31-2000667 Rev. 117
Installation
12 CHECK BURNERS
WARNING FireorExplosionHazard:Donot
operatetheburnerwithoutallburnerpartsinplace.
A. Burners-Placesurfaceburnersintocorresponding
positionsoncooktop.
B. Caps-Placecapsonpropersizeburner.
C. Grates-Theleftandrightgratesare
interchangeable.Placethegratesonthecooktop.
FINALIZE INSTALLATION
Placetheburnergratesovertheburners.Thegrates
shouldbeseatedandshouldnotrock.
Thegriddleissecuredwithscrews.Itisdesignedto
bestationaryandshouldnotberemoved.
Thegriddlehastwolevelingscrewsbeneaththerearflue
coverthatcanbeusedtoadjusttothedesiredslope.
Thetwoinnerscrewsareclampingscrewsfor
securingthegriddleinplace.Loosenthesetwoscrews
beforeleveling.Donotremovethesetwoscrews.
Thetwoouterscrewsarelevelingscrews.Donot
removethesetwoscrews.Theycanbeturnedtolevel
thegriddleortoprovideaforwardslopetohelpgrease
andoilsdrainawayfromthefoodbeingcooked.
Afterlevelingthegriddle,hand-tightentheclamping
screws;donotover-tighten.
WHEN ALL HOOKUPS ARE
COMPLETED
Makesureallcontrolsareleftintheoffposition.Make
suretheflowofcombustionandventilationairtothe
range is unobstructed.
Checkthatallpackingmaterialsandtapehavebeen
removed.Thiswillincludetapeonmetalpanelunder
controlknobs(ifapplicable),adhesivetape,wire
ties,cardboard,andprotectiveplastic.Failureto
removethesematerialscouldresultindamagetothe
appliance once the appliance has been turned on and
surfaceshaveheated.
13 CHECK SURFACE BURNERS
PushandturnaknobtotheLITEposition.Aclicking
sound indicates proper operation of the ignition
system.Whenlightinganyburner,sparkswillappear
atallburnersbutgasflowsfromonlytheoneselected.
Onceairispurgedfromthesupplyline,burnershould
lightwithin4seconds.Afterburnerlights,rotatethe
knoboutoftheLITEposition.Tryeachburnerin
successionuntilallburnershavebeenchecked.
Quality of Flames
Determinethequalityofflamesvisually.Normal
burnerflamesshouldlooklike(A)or(B).
Long,brightyellowflamesarenotnormal.Normal
flamesmayshowsignsofanorangetintwhenwell
heatedorsignsofflickeringorangeduetoparticlesin
the gas or air.
(A) Soft blue flames—
Normalfornaturalgas
(B) Yellow tips on
outer cones—
Normalforpropane(LP)gas
BurnerCapNotProperlySeated
BurnerCapProperlySeated
GriddleFlueCover
ClampingScrews
LevelingScrews

18 31-2000667 Rev. 1
Accessory Installation
TOEKICK (included)
■Installthetoekickaftertherangehasbeenleveled.
■Measurethedistancebetweenthefloorandthe
bottom of range.
■Loosenthetwoscrewsoneachend.Adjustthe
toekickheightbyslidingtheupperandlowerpieces
apartto1/8”lessthanthemeasuredheight.
■Securethetopandbottomsectionsbytighteningthe2
screwsoneachend.
■Pushtoekickagainstrangeleguntilclipsnapstolegs.
NOTE:Besurethetoekicksnapssecurelytotheleg.
Bottom
ofToekick Screw
Top of
Toekick
Push
Push

31-2000667 Rev. 119
OPTIONAL ACCESSORIES—12”HIGH BACKSPLASH
UX12BS36PSS, UX12BS48PSS Accessory Installation
Thiskitprovidesfortheinstallationofa12”high
backsplashfor36”ProfessionalRangesandRangetops.
TOOLS AND MATERIALS REQUIRED
■Glovestoprotectagainstsharpedges
■T-15and#2Phillips
screwdrivers
■Drillwith3/32”and
9/64”bits
■Safetyglasses
■Level
■Pencil
This Kit Includes
■Wallsupportpanel
■Coverpanel
■Hardwarepackagewith
 –5StainlessSteelTorx15
#8self-tappingscrews
 –5Phillips#2panheadwood
#10screws
INSTALL 12” BACKSPLASH
WARNING Thisbacksplashmustbesecurely
fastenedtothewall.Failuretodosocouldresultin
damage or personal injury.
■Installandleveltherangeorrangetopandthe
range hood according to the installation instructions.
■Removethebacksplashpackagingandprotective
film.
■Usealeveltopencilahorizontallineonthewall,1/8”
abovetherangeorrangetop.The1/8”gapallowsthe
coverpaneltooverlapthewallsupportpanel.
■Locatewallstudsoneachside.Wherestudsarenot
available,plantousewallanchors(notprovided).
■Alignthewallsupportpanelonthemarked
horizontallineandcenteredlefttoright.
■Thewallsupportpanelmustbesecuredtothewall
atall4corners.Usewoodscrews(provided)orwall
anchors(notprovided)tosecurethesupportpanel
tothewall.
■Placethecoverpaneloverthewallsupportpanel
andsecurewithTorxscrews(provided).Install2
screwsoneachside.
Install4WoodScrews
WallSupportPanel
CoverPanel
Hardware
Package
761Dia65
InstallT-15
Screws
Wall
Support
Panel CoverPanel
WallSupport
Panel
Center
Arrow
1/8”
CoverPanel

20 31-2000667 Rev. 1
ACCESSORIES—30” TO 36” ADJUSTABLE BACKSPLASH (not included)
UXADBS36PSS, UXADBS48PSS Accessory Installation
■Thisbacksplashadjuststofitthespacebetween
thetopoftherangeandthebottomofthehood,
from30”Min.to36”Max.height.
■Maximumshelfload-bearingweightis40lbs.
TOOLS AND MATERIALS REQUIRED
■Glovestoprotectagainstsharpedges
■T-15and#2Phillipsscrewdrivers
■Drillwith3/32”and9/64”bits
■Safetyglasses
■Level
■Pencil
This Kit Includes
■Topwallsupport
■Bottomwallsupport
■Topcoverwithshelf
■Bottomcover
■Hardwarepackagewith
 –9StainlessSteelTorx15#8
self-tappingscrews
 –9Phillips#2panheadwood
#10screws
 –3StainlessSteel#2trusshead
#10screws(foralternate
installationmethod)
INSTALL THE WALL SUPPORT PANELS
WARNING Thewallsupportpanelsmustbe
securelyfastenedtothewall.Failuretodosocould
result in damage or personal injury.
IMPORTANT:Thisbacksplashisdesignedtocover
thewallbetweenthebottomofthehoodandthetopof
therange.Theventhoodshouldbeinstalledoverthe
rangetoporrangebeforeinstallingthisbacksplash.
■InstallandleveltheRange/Rangetopaccordingto
the product installation instructions.
■Removebacksplashpackagingandprotectivefilm.
■Locatewallstudsoneachside.Wherestudsarenot
available,plantousewallanchors(notprovided).
■Usealeveltopencil2horizontallinesonthewall,
one1/8”belowtheventhoodandtheother1/8”
abovetheRange/Rangetop.This1/8”spaceallows
thecoverpanelstooverlapthewallsupports.
■Securethetopwallsupportpaneltothewallwith4
woodscrews,throughtheoutermoststuds.
■Use4woodscrewstosecurethebottomwallsupport
panel. The center slot should be positioned at the top.
Thegapbetweenthetopandbottomsupportpanels
willbecoveredbythetopcoverwithshelf.
Hardware
Package
761Dia65
TopCover
withShelf
BottomCover
BottomWallSupport
TopWall
Support
1/8”
Securethe
top panel to
thewallwith4
woodscrews
1/8”
Securethe
bottom panel to
thewallwith4
woodscrews
Wood
Screws
Center
Arrow
Wood
Screws