Monoprice Blackbird 36633 User manual

Blackbird™4K HDMI® KVM Switch
P/N 36633
User's Manual

2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra
attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do
not place drinks or other containers with moisture on or near
the device. If moisture does get in or on the device, immediately
unplug it from the power outlet and allow it to fully dry before
reapplying power.
Do not touch the device, the power cord, or any other
connected cables with wet hands.
Do not subject the product to extreme force, shock, or
fluctuations in temperature or humidity.
Prior to operation, check the unit and power cord for physical
damage. Do not use if physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the
outlet provides the same type and level of power required by
the device.
Unplug this device from the power source when not in use.
Take care to prevent damage to the power cord. Do not allow it
to become crimped, pinched, walked on, or become tangled
with other cords. Ensure that the power cord does not present a
tripping hazard.
Never unplug the unit by pulling on the power cord. Always
grasp the connector head or adapter body.

3
Ensure that power is turned off and disconnected before
making any electrical connections.
Clean using a soft, dry cloth only. Do not use chemical cleaners,
solvents, or detergents. For stubborn deposits, moisten the
cloth with warm water.
This device has no user serviceable parts. Do not attempt to
open, service, or modify this device.
INTRODUCTION
Thank you for purchasing this Blackbird™ 4K HDMI® KVM Switch! This
switch allows you to connect up to four computers with HDMI video
output and control them using a remote keyboard and mouse. It
supports video resolutions up to 4K@60Hz with 4:4:4 color sampling and
can upscale lower resolutions to 4K@60Hz. Up to 5 units can be
cascaded, allowing for control of up to 16 computers in total. It supports
fullscreen and quadview layouts and includes an IR remote control, as
well as RS-232, and Web UI control options.

4
FEATURES
Supports fullscreen and quadview modes
Supports input and output resolutions up to 4K@ 60Hz with
4:4:4 color sampling
Can upscale to 4K@60Hz
Up to 5 units can be cascaded, allowing for control of up to 16
computers
Supports seamless movement of the mouse across four screens
in quadview mode
Fast switching between input channels or screen layout modes
Supports keyboard/mouse, front panel button, IR remote
control, RS-232 control, and web UI control options
Complies with the HDMI® 2.0 and HDCP™2.2 standards
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring
that your ordering, purchasing, and delivery experience is second to
none. If you have any problem with your order, please give us an
opportunity to make it right. You can contact a Monoprice Customer
Service representative through the Live Chat link on our website
www.monoprice.com or via email at [email protected]. Check
the website for support times and links.

5
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all
the items listed below. If anything is missing or damaged, please contact
Monoprice Customer Service for a replacement.
1x 4K HDMI® KVM switch
1x IR remote control
1x AC power adapter (12 VDC, 2A)
2x Rack mount brackets
4x Rubber feet
1x Bag of screws
1x User's manual
PRODUCT OVERVIEW
Front Panel
1. IR Receiver: IR receiver for accepting signals from the included
IR remote control.
2. HDMI1 Input: Press the button to select the HDMI® 1 input and
its corresponding USB input.
3. HDMI2 Input: Press the button to select the HDMI 2 input and
its corresponding USB input.

6
4. HDMI3 Input: Press the button to select the HDMI® 3 input and
its corresponding USB input.
5. HDMI4 Input: Press the button to select the HDMI 4 input and
its corresponding USB input.
6. Fullscreen Output: Press the button to select the fullscreen
output layout.
7. Quadview Output: Press the button to select the quadview
output layout.
8. Panel Lock: Press the button to lock or unlock the front panel
buttons.
9. Standby: Press the button to put the system into standby mode
or to power it on.
Rear Panel
1. Output: HDMI® video connector and two USB Type-A ports for
the keyboard and mouse.
2. HDMI1/USB1: HDMI video and USB Type-B ports for connecting
the first computer.
3. HDMI2/USB2: HDMI video and USB Type-B ports for connecting
the second computer.
4. HDMI3/USB3: HDMI video and USB Type-B ports for connecting
the third computer.

7
5. HDMI4/USB4: HDMI® video and USB Type-B ports for
connecting the fourth computer.
6. Audio Out: 3-pin Euroblock connector for connecting an
external amplifier.
7. Ethernet: RJ45 port for connecting a computer or Ethernet
network.
8. RS232: 9-pin DB-9 serial connector for connecting a computer
for RS-232 control.
9. USB FW Upgrade: USB Type-A port for connecting a USB flash
drive to perform a firmware upgrade.
10. 12VDC: DC barrel connector for connecting the included AC
power adapter.
11. Power On/Off: Master power switch for turning the unit on or
off.
IR Remote Control
1. Standby: Press the button
to put the system into
standby or to power it on.
2. Mute: Press the button to
turn audio muting on or off.
3. Lock: Press the button to
lock or unlock the front
panel buttons.
4. Info: Press the button to
view the system
information.

8
5. Resolution: Press the Auto button to set the output resolution
to Auto. Press the Loop button to cycle through the available
output resolutions.
6. Layout: Press the button to toggle between the fullscreen and
quadview layouts.
7. Input: Press one of the buttons to select the corresponding
input. When in fullscreen mode, it selects the entire
corresponding input (audio and video). In quadview mode, it
selects the corresponding audio only.
8. Audio Src: Cycle the output audio through the available audio
inputs.
9. Video B: Not used.
SAMPLE CONNECTION DIAGRAM

9
KVM FUNCTIONALITY
The KVM switch can be controlled using the connected mouse and
keyboard without any special configuration. A mouse with a scroll wheel
is highly recommended for maximum KVM control functionality.
When quadview mode is enabled, the top left screen (HDMI® 1) is active
by default. Moving the mouse cursor to the border of the screens in
quadview will automatically switch the active window. The KVM switch
responds to the following mouse actions:
Scroll Wheel: Scrolling syncs the coordinates between the
source computer and the KVM switch.
Scroll Wheel/Middle Mouse Button: When in quadview mode,
double-clicking the Scroll Wheel/Middle Mouse Button switches
to fullscreen mode with the active window. When in fullscreen
mode, double-clicking the Scroll Wheel/Middle Mouse Button
switches to quadview.
As with other KVM switches, the mouse cursors on inactive windows
remain on screen.

10
WEB UI CONTROL
You can control the KVM switch using a computer connected through
the Ethernet port on the rear panel. You can connect directly or through
an existing Ethernet network.
Direct Connection
Perform the following steps to connect your computer directly to the
KVM switch. These instructions assume the use of the Windows®
operating system.
1. Plug one end of an Ethernet cable (not included) into the
Ethernet port on the rear panel of the KVM switch, then plug
the other end into the Ethernet port on your computer.
2. On your computer, click Start > Control Panel > Network and
Sharing Center.
3. Click the Change adapter settings option.
4. Right click Local Area Connection, then select the Properties
option.
5. Highlight Internet Protocol
Version 4 (TCP/IPv4), then
click the Properties button.
6. Select Use the following IP
Address for static IP
address. Set the IP Address
to any address between
192.168.1.1 to 192.168.1.255,
except 192.168.1.202.