Monstertech MTX BASE FRAME User manual

MTX BASE FRAME
Instruction Manual EN

MTX BASE FRAME INSTRUCTION MANUAL
2
1 General information
Congrats on your brand new MTX Base Frame!
This guide is meant to help you assemble your Sim Rig as smoothly as possible. If you still
have questions about the assembly process, please contact [email protected].
1.1 Before you start
Before you start the MTX Base Frame assembly, we are going to look at some common as-
sembly steps and often used parts, as well as required tools.
1.1.1 Required Tools
For our Sim Rig assembly, we need following tools*:
- Hex key set with ball head with extension
- Rubber or plastic mallet
- Flat head screwdriver
- Tape measure w/ millimeters
*Tools are not included with the Sim Rig

MTX BASE FRAME INSTRUCTION MANUAL
3
1.1.2 Inserting T-Nut into Profile
There are two ways to insert the M8 T-Nuts into the respective prole groove; refer to Figure 1
and 2 respectively.
Figure 1: Slide in from side
Figure 2: Rotate in from top

MTX BASE FRAME INSTRUCTION MANUAL
4
1.1.3 Universal Fastener Assembly
The universal fastener assembly can be prepared the following way, so long as the T-Nut can
be slid in from the side. One Universal Fastener Assembly is made up from one (1) M8x30 Hex
Screw, one (1) T-Nut, and one (1) Universal Fastener.
Figure 3: Universal fastener assembly
If inserting the universal fastener assembly from the side is not possible, it is necessary to rota-
te the T-Nut into the prole groove rst, and then screw the M8x30 bolt (along with the univer-
sal fastener) into the T-Nut.

MTX BASE FRAME INSTRUCTION MANUAL
5
1.1.4 Angle Bracket Stud Removal
Sometimes it might be necessary to break off the studs from angle brackets (if those are part
of the product). This is best achieved by:
1. Inserting a at-head screwdriver between the stud and the bracket, and then
2. Rotate the screwdriver for the stud to come off

MTX BASE FRAME INSTRUCTION MANUAL
6
1.1.5 Angle Bracket Assembly
For some assemblies the use of angle brackets is required. These are prepared by using two
(2) M8x18 hex screws, two (2) washers, and two T-Nuts.
Figure 5: Angle bracket assembly
1.1.6 Adjustment of Profile Feet
The prole feet are installed on the MTX Base Frame or MTX Stand-Alone TV
Figure 6: Prole feet

MTX BASE FRAME INSTRUCTION MANUAL
7
2 Overview
2.1 Completed MTX Base Frame
Base - Overview
Figure 8: Complete MTX base frame
Use the above image as reference for the following MTX Base Fra-
me assembly instructions.

MTX BASE FRAME INSTRUCTION MANUAL
8
3.1
Figure 9: Frame assembly - step 1
3.2
Figure 10: Frame assembly - step 2

MTX BASE FRAME INSTRUCTION MANUAL
9
3.3
Figure 11: Frame assembly - step 3
3.4
Figure 12: Frame assembly - step 4

MTX BASE FRAME INSTRUCTION MANUAL
10
3.5
Figure 13: Frame assembly - step 5
3.6
Figure 14: Frame assembly - step 6

MTX BASE FRAME INSTRUCTION MANUAL
11
3.7
Figure 15: Frame assembly - step 7
3.8
Figure 16: Frame assembly - step 8

MTX BASE FRAME INSTRUCTION MANUAL
12
3.9
Figure 17: Frame assembly - step 9
3.10
Figure 18: Frame assembly - step 10

MTX BASE FRAME INSTRUCTION MANUAL
13
3.11
Figure 19: Frame assembly - step 11
3.12
Figure 20: Frame assembly - step 12

MTX BASE FRAME INSTRUCTION MANUAL
14
3.13
Figure 21: Frame assembly - step 13
3.14
Figure 22: Frame assembly - step 14

MTX BASE FRAME INSTRUCTION MANUAL
15
3.15
Figure 23: Frame assembly - step 15
3.16
Figure 24: Frame assembly - step 16

MTX BASE FRAME INSTRUCTION MANUAL
16
4 Pedal Mount
Figure 25: Pedal mount

MTX BASE FRAME INSTRUCTION MANUAL
17
4.1
Figure 26: Pedal mount assembly - step 1
4.2
Figure 27: Pedal mount assembly - step 2

MTX BASE FRAME INSTRUCTION MANUAL
18
4.3
Figure 28: Pedal mount assembly - step 3
4.4
Figure 29: Pedal mount assembly - step 4

MTX BASE FRAME INSTRUCTION MANUAL
19
4.5
Figure 30: Pedal mount assembly - step 5
4.6
Figure 31: Pedal mount assembly - step 6

MTX BASE FRAME INSTRUCTION MANUAL
20
4.7
Figure 32: Pedal mount assembly - step 5
4.8
Figure 33: Pedal mount assembly - step 6