Monte Carlo Fan Company 3HYR56**D Series User manual

Ceiling Fan Installation Instructions
57' &&!,70,8(48
!$"!!" #"!
Total fan weight
with light kit
% ?!
#

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),
including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-
ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7
feet from the floor to the trailing edge of the blade.
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and
use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating
blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067R manufactured by
Rhine Electronic Co., Ltd. Suitable for use with solid-state speed controls.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-
ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
Air flow direction: warm weather - switch to left - forward / cool weather - switch to right - reverse
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
WARNING: TO REDUCE THE RIS OF FIRE, ELECTRIC SHOC , OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
!"' "!
"! # 
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)

Installation
Use metal outlet box suitable for fan support
and use only the screws provided with the out-
let box (must support 35 lbs). Before attaching
fan to outlet box, ensure the outlet box is
securely fastened by at least two points to a
structural ceiling member ( a loose box will
cause the fan to wobble). #8,542>9/,8*7,<8
675;0+,+<09/9/,5:92,9)5=

Remove cotter pin from ball, and
save for later use.

Place canopy over down rod.
 
Place Yoke Cover over down rod.

Thread leadwires and safety cable
through the downrod.

Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans you
can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more
than one fan with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches

white
black
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Blue from fan to blue from remote
marked light. Black from fan to Black from
remote marked L. White from house to white
from remote marked AC N . Black from house
to Black from remote marked AC L. Connect
all green ground wires to Ground wire from
House.
blue
Green
white
black
House
Fan

fuse
Install remote receiver into the
mounting bracket.

Ready for wiring.

Make sure the studs protruding from the
bottom of the Mounting bracket are
installed with threads all the way through
the bracket.

Loosen the 2 screws on the yoke to
allow down rod to slip into yoke.

Insert down rod into yoke on top of
the fan body. Align the hole in the
down rod with the hole in the yoke.
Insert the Pin through the yoke and
down rod until the point appears on
the other side.

Install keeper pin.

Tighten the 2 set screws on the
yoke, once the down rod is in place.

Hang assembled fan from the mounting bracket
installed to ceiling in previous step. Make sure the
fan is hanging straight. Rotate fan until the tab on
the Mounting bracket engages the slot on the
Downrod Ball. This must be done to prevent the fan
body from rotating when the blades are in motion.

For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both flush
and downrod mode the safety cable must be
installed into the house structure beams using
the 3” lag screws,washers, and lock washers.
provided. Make sure that when the safety cable
is fully extended the leadwires are longer than
the cable and no stress is placed on the lead-
wires.
 Safety cable installation
!(-,9>()2,
(.!*7,<
safety
cable
3” lag
screw
lock
washer
washer

Align keyslot holes of light kit plate
and twist the plate to lock. Install
the screw removed in step 22 and
tighten securely. Loosen two screws and remove one
screw from light plate. eep the
screw removed for later use.
 
Remove final nut, final cap, hex nut
and rubber washer from light kit.

Connect the white wire from fan to
white wire from light kit, then con-
nect the blue wire from fan to black
wire from light kit.

Aline keyslot holes of the light fixture
and twist it to lock. Install the screw
removed in step 24 and tighten
securely.

Install 3x40W bulbs provided.
*%(7404.: Over lamping the fan will
result in the fan lights shutting down till
the proper wattage of bulbs are installed.
Reset the lights by turning off the wall
switch, bracker, or by remote. Replace
bulbs with the correct wattage bulbs, turn
the power on*.

Lift canopy and install knurled nuts as
shown. Tighten the knurled nuts securely.
The canopy should adjust for any irregu-
larity in the ceiling or Outlet box.

Check motor for shipping stabilizers and
remove if present. Attached blades using
screws and fiber washers in hardware
pack. Tighten screws securely. Repeat this
procedure 4 more times.

Loosen two screws and remove one
screw. eep the screw removed for later
use.

Atathced the glass to light fitter.
Install the rubber washer and hex
nut which were removed from step
25 to the thread rod and secure the
glass.

Install the final cap and final nut which
were removed from step 25 to the thread
rod by screwing to secure the glass.
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded con-
ductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on
the other side of the outlet box. The splices after being
made should be turned upward and pushed carefully
up into the outlet box.



Place face plate over battery compartment and
buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snapping into place. Install wall control unit to outlet box
using machine screws provided.
 HAND HELD INSTALL WALL MOUNT INSTALL
Attach front cover to wall control with
screws provided. Snap battery cover
in place.

Remove battery cover. Install 12V battery into
wall remote. Duracell MN21 / Eveready A23 / GP
23A all 12V.Attach cover of remote by placing
over buttons and snap the battery cover in
place.


,359,549752"7(483099,7
,(9:7,8
! Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
" To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. Light will
maintain last setting if turned off.
 %  $ ! Depress rev button allow a few seconds for remote to
change rotation direction with fan running.
HIGH SPEED
MEDIUM SPEED
LOW SPEED
FAN OFF SETTING
(Turns fan off only)
FAN REVERSE
(Press once to
change direction of
the fan)Fanmust be
running to reverse.
LIGHT ON/OFF SET-
TING AND DIMMER
(Press and hold to
dim light infinitively)
LED LIGHT

1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
#"(1,8:7,3(0465<,7089:74,+5--
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch
is in the middle.
4.Make sure that shipping stabilizer tabs have been removed from motor.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.
4.Some fan motors are sensitive to signals from Solid State variable speed controls.
"#!(!520+!9(9,;(70()2,86,,+*549752
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this
period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in
Step #6 of Downrod Mount installation).
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junc-
tion box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a
point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to ceilng.
eeping measure within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat
for each blade. If all blade levels are not equal, you can adjust blade levels by the following procedure.
To adjust a blade tip down, insert a washer (not supplied) between the blade and blade holder at the
screw closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the blade and
blade holder at the two screws farthest from the motor. Reverse the position of the washer if blades
mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute
the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
%  ;,72(3604.9/,-(4<0227,8:29049/, -(420./988/:9904.+5<4 :4902
9/, 6756,7<(99(.,5-):2)8(7,0489(22,+ ,8,99/,20./98)>9:7404.5--9/,<(22
8<09*/)7,(1,757)>7,359, ,62(*,):2)8<09/9/,*577,*9<(99(.,):2)89:749/,65<,7
54
#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.(4+57
*(456>
% ,-57,(99,36904.957,62(*,9/,-:8,3(1,8:7,9/,3(0465<,7089:74,+5--95
9/,-(4 ,62(*,542><09/((36-:8,:8,080480+,9/,*(456>549/,)2:,<07,95
7,359,7,*,0;,76:8/(4+9<0899/,*(69556,49/,-:8,*(8,
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our
Customer Service Center at the
number printed on your parts list insert sheet.
%(7404.,-57,8,7;0*04.57*2,(404.:409!<09*/65<,75--(9!,7;0*,6(4,2(4+25*18,7;0*,+08*544,*904.
3,(489567,;,4965<,7-753),04.8<09*/,+54(**0+,49(22>%/,49/,8,7;0*,+08*544,*904.3,(48*(4459
),25*1,+8,*:7,2>-(89,4(675304,49<(7404.+,;0*,8:*/(8(9(.959/,8,7;0*,6(4,2
Trouble Suggested Remedy
Customer Service Center:
301 West Washington St.
Riverside,NJ 08075
1-800-519-4092
www.montecarlofans.com