Monte Carlo Fan Company 3LRR66 Service manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proo o purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your ixture, please visit our website www.montecarlo ans.com
3LRRXXD Series Fan
Total an weight with light kit
UL Model No. : 3LRR66/52
10.6 kgs
23.4 lbs
Shown with 66”
blades
Shown with 52” blades
Energy Star approved with
52” blades

© 2011 Monte Carlo Fan Company 2/9/2012
2
WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G
READ A D SAVE THESE I STRUCTIO S
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RYK manufac-
tured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
ever place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Cutomer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlo ans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 2/9/2012
3
Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting
means to prevent power from being switched on ac-
cidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warn-
ing device, such as a tag, to the service panel.
1
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
2
4
Remove cotter pin from downrod, and
save for later use.
5
Place canopy over downrod.
6
Loosen the 2 set screws until the do
not protude into the inside of the
yoke.
Use metal outlet box suitable for fan support and
use only the screws provided with the outlet
box (must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securely fas-
tened by at least two points to a structural ceiling
member ( a loose box will cause the fan to wobble).
Remove the two outlet box screws provided with
the box, aligning the holes of the mounting bracket
with the holes of the outlet box. Re-install the 2
outlet box screws securely.
3
Place yoke cover over downrod.
78
Thread the leadwires and safety
cable through the downrod.
9
Insert downrod into the yoke on top
of fan body. Align the hole in the
downrod with the hole in the yoke.
Insert cotter pin through yoke and
downrod until point appears on the
other side

© 2011 Monte Carlo Fan Company 2/9/2012
4
Make sure the studs protruding from the
bottom of the Mounting bracket are in-
stalled with threads all the way through
the bracket.
12
Tighten the 2 set screws on the yoke,
once the down rod is in place.
11
Hang assembled fan from the mounting bracket in-
stalled to ceiling in previous step. Make sure the fan
is hanging straight. Rotate fan until the tab on the
Mounting bracket engages the slot on the Downrod
Ball. This must be done to prevent the fan body from
rotating when the blades are in motion.
13
Install keeper pin.
10
Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans
you can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more
than one fan with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
14
Install remote receiver into the
mounting bracket.
15
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Blue from fan to blue from remote marked
light. Black from fan to Black from remote
marked L. White from house to white from re-
mote marked AC N . Black from house to Black
from remote marked AC L. Connect all green
ground wires to Grounded wire from House.
18
Ready for wiring.
16
For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both flush
and downrod mode the safety cable must be in-
stalled into the house structure beams using the
3” lag screws,washers, and lock washers. pro-
vided. Make sure that when the safety cable is
fully extended the leadwires are longer than the
cable and no stress is placed on the leadwires.
17 Safety cable installation
Safety Cable
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer

© 2011 Monte Carlo Fan Company 2/9/2012
5
Connect white wire from fan to White
wire from light fixture. Connect blue
wire from fan to Black wire from light
fixture.
23
Lift canopy and install knurled nuts as
shown. Tighten the knurled nuts securely.
The canopy should adjust for any irregu-
larity in the ceiling or utlet box.
20
Check for shipping stabilizers and remove
if present. Attach blades using screws in
hardware pack. Blades sold seperately.
Tighten screws securely. Repeat 2 more
times.
21
Loosen 2 screws are remove one screw.
Keep removed screw for later use.
22
Alighn keyslot holes of light kit plate and
twist to lock clockwise. Install screw re-
moved in step 22 and tighten all screws
securely.
24
Remove battery cover. Install 12V battery into
wall remote. Duracell MN21 / Eveready A23 / GP
23A all 12V.Attach cover of remote by placing
over buttons and snap the battery cover in place.
25
Place face plate over battery compartment and
buttons. Place remote over 2 pins on front cover.
Attach cover of remote by placing over 4 pins
and snapping into place. Install wall control unit to outlet box
using machine screws provided.
2726 HAND HELD INSTALL WALL M UNT INSTALL
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of the
wirenut. After making the wire connections, the wires
should be spread apart with the grounded conductor
and the equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on the other
side of the outlet box. The splices, after being made,
should be turned upward and pushed carefully up into
the outlet box.
19

© 2011 Monte Carlo Fan Company 2/9/2012
6
Attach front cover to wall control with
screws provided. Snap battery cover
in place.
28
Attach blanking plate by locating dim-
ples in light fixture with grooves in
the blanking plate and twist clock-
wise.
29
For fan without
bulb, go to step
29.
For fan with
bulb, go to step
30
Attach the GU24 18W CFL bulb and
secure by twisting clockwise. Bulb in-
cluded.
WA NING: USE MAXIMUM GU24 18
WATTS LISTED SBCFL(SELF-BALLASTED
C MPACT FLU RESCENT LAMP) NLY, N T
USING SBCFL WILL VERHEAT THE UNIT
AND CAUSE DAMAGE T THE UNIT R THE
FAN WHICH THE UNIT IS INSTALLED T -
GETHER.
30
Attach the glass by locating dimples in
light fixture with groves in the glass
and twist clockwise until tight.
31

© 2011 Monte Carlo Fan Company 2/9/2012
7
WA NING: This fixture is not dimmable. Use only with on/off switch.
Do not use in conjunction fan/light remote controls or light dimmers.
emote Control Transmitter Features:
FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGHT ON/OFF To turn light on, press light button once quickly. To turn off
press once quickly while light is on.
FO WA D/ EVE SE Depress rev button allow a few seconds for remote to
change rotation direction with fan running.
HIGH SPEED
MEDIUM SPEED
LW SPEED
FAN FF SETTING
(Turns fan off only)
FAN REVERSE (Press
once to change direc-
tion of the fan) Fan
must be running to
reverse.
LIGHT N/ FF SETTING
(Press to turn on/off light)
LED LIGHT

© 2011 Monte Carlo Fan Company 2/9/2012
8
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when
switch is in the middle.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Some fan motors are sensitive to signals from Solid State variable speed controls.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this
period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting
a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to
ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-
ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-
lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and
blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade holder at the two screws farthest from the motor. Reverse the position
of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute
the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WA NING: USE MAXIMUM GU24 18 WATTS LISTED SBCFL(SELF-BALLASTED COMPACT FLUO ES-
CENT LAMP) ONLY, NOT USING SBCFL WILL OVE HEAT THE UNIT AND CAUSE DAMAGE TO THE
UNIT O THE FAN WHICH THE UNIT IS INSTALLED TOGETHE .
CAUTION: Make sure main power is turned off before entering switch housing and/or
canopy.
User Servicing Instructions
WA NING: Before attempting to replace the fuse make sure the main power is turned off
to the fan. (Fuse is inside the canopy on the blue wire to remote receiver, push and twist
the cap to open the fuse case) Push and twist to reassemble fuse.
isk of fire. eplace fuse only with 3 amp, 125 volt fuse.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TR UBLE SH TING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Cus-
tomer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.

Jan.27.10 revise - Add ES logo, ES approved with 52” blades
Feb.2012 New format