Monte Carlo Fan Company 3SU54BK Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as yo r proof of p rchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register yo r fixt re, please visit o r website www.montecarlofans.com
3SU54 Series Fan
Total fan weight
UL Model No. : AC-356
9.02 kgs
19.84 lbs

© 2011 Monte Carlo Fan Company 2/11/2012
2
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO ERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NF A
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 10 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or ersonal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws rovided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-
move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire rotection Association (NF A), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Tools Required for Assembly (not included): Electrical Tape, hillips Screwdriver, liers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 2/11/2012
3
Insert downrod into motor yoke.
Next, insert clevis pin through y oke
and downrod and secure with cotter
pin.
Before you begin installing the fan, S witch power off
at Service panel and lock service disconnecting means
to prevent power from being switched on accidentally .
When the service disconnecting means cannot be
locked, securely fasten a prominent w arning device,
such as a tag, to the service panel.
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per -
sonal injury, mount to outlet bo x or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
Install the Mountiing Bracket to the
Outlet box. Use only the screws
provided with the outlet box.
Remove keeper from pin. (see
inset) Loosen the 2 set screws in
yoke for downrod to slip into
yoke.
3
21
46
Thread wires and safety cable
through downrod with canopy and
yoke cover assembled.
5
Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on the
ball engages the ridge in the mounting br acket.
This will allow hands-free wiring.
8
7
Tighten both yoke set screws to fur-
ther secure downrod.
For Canadian installation and for USA fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The Secondary Support Safety
Cable in the U.S., Do Not Remove Knockouts In
The Outlet Box.
9Safety cable installation
Safety Ca le
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer

© 2011 Monte Carlo Fan Company 2/11/2012
4
Remove any shipping stabilizers if
present. Attach blade assembly to
motor using the motor screws and
washers provided. Tighten screws
securely.
13
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on
the other side of the outlet bo x.
10
For pullchain controls, follow diagram above.
Make sure that all exposed wiring is secured
inside wire nuts. Note: Wires from house ma y
vary in color and ma y not include ground wire.
After wiring is conplete, gently push wires into
junction box with wire nuts pointing upw ard.
Refer to point 3 of safet y tips.
11 House Fan
Black
White
Green
Black
White
Green(downrod)
Green(Bracket)
Blue
Remove 3 screws from the switch
housing plate and save to re-install
into the switch housing.
14
Loosen one and remove one pre-
assembled screw from mounting
bracket. Save screw. Lift canopy up,
aligning its keyhole slot with the pre-
assembled screw on mounting
bracket and twist clockwise to lock in
place. Re-install the removed screw
and tighten all screws securely.
12
Install the switch housing using the
3 screws previously removed.
Setting the reverse switch in the
left hand side will result in
downward airflow and setting the
switch in the right hand side will
result in upward airflow.
15
Reverse switch

© 2011 Monte Carlo Fan Company 2/11/2012
5
1.Check main and branch circuit fuses or circuit break ers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
1.Check to make sure all screws in motor housing are snug (not o ver tightened).
2.Check to make sure wire nut connectors in switch housing are not r attling against each other
or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
3.Some fan motors are sensitive to signals from Solid State v ariable speed controls.
DO NOT USE a Solid State variable speed control.
4.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.All blades are weighed and grouped b y weight. Natural woods vary in density which could
cause the fan to wobble ev en though all blades are weight -matched. The following procedures
should eliminate most of the wobble. Check for wobble after each step .
2.Make sure that the ridge of the canop y engages the notch in the downrod ball.
3.Check that all blades are screwed firmly into blade holders.
4.Check that all blade holders are tightened securely to motor .
5.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x
and junction box is mounted firmly to ceiling joist.
6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can redis -
tribute the weight and possibly result in smoother oper ation.
1.Check wire from fan to mak e sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble Shooting
If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors ma y be mistaken for defects. If you experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty in installation, please call our
Customer Service Center at the number printed on y our parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
TROUBLE SUGGESTED REMEDY

Feb.2012 New format
Jul.2013 Update for CUL regulation
Aug.2013 update fan wieght