Monte Carlo Fan Company 5vsr44XXd-l series User manual

Ceiling Fan Installation Instructions
68%"!''"-81-9)59
!"%#""#!$#"
Total fan weight
&!@"
$
59:)33=1:068
=1:06;::0-31/0:21:

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),
including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-
ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7
feet from the floor to the trailing edge of the blade.
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and
use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating
blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-
ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
Air flow direction: warm weather-switch to left - forward / cool weather -switch to right - reverse
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
WARNING: TO REDUCE THE RISK OF FIRE, E ECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FO OWING: READ AND SAVE THESE INSTRUCTIONS
"#( #"
#" ! $!
Phillips Screwdriver Wire Cutters Pliers Step adder
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)

Installation
Use metal outlet box suitable for fan support
and use only the screws provided with the out-
let box (must support 35 lbs). Before attaching
fan to outlet box, ensure the outlet box is
securely fastened by at least two points to a
structural ceiling member ( a loose box will
cause the fan to wobble). $9-653?:0-
9+8-=9786<1,-,=1:0:0-6;:3-:*6>

Uninstall the flywheel by removing
the set screws. Save the screws for
use later.
Remove the rubber ring and discard
it.

Place the flywheel back and fix it by
the screws removed from step 4.
Tighten the 5 screws securely.


For Canadian installation in both flush and down-
rod mode the safety cable must be installed into
the house structure beams using the 3” lag screws
provided. Make sure that when the safety cable is
fully extended the leadwires are longer than the
cable and no stress is placed on the leadwires.
Hang assembled fan from the mounting bracket
installed to ceiling in previous step. Make sure the
fan is hanging straight. Rotate fan until the tab on
the Mounting bracket engages the slot on the
Downrod Ball. This must be done to prevent the fan
body from rotating when the blades are in motion.
 
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded con-
ductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on
the other side of the outlet box.
Canadian mounting only
Safety Cable
ag Screw

ag Screw
Washer
ock Washer
Safety Cable
Place blade holders onto blades aligning holes
in blade holder with holes in blade. Make sure
that the side of the blade you select is facing
downward. Install 3 screws and fiber wash-
ers to back side of blade as shown. Tighten
screws securely. Repeat this process 4 more
times until all blades are assembled.

Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans you
can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more
than one fan with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches

Install remote receiver into the
mounting bracket.

Ready for wiring.

white
black
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Blue from fan to blue from remote marked
light. Black from fan to Black from remote
marked . White from house to white from
remote marked AC N . Black from house to
Black from remote marked AC . Connect all
green ground wires to Ground wire from
House.
blue
Green
white
black
House
Fan

fuses
ift canopy and install knurled nuts as
shown. Tighten the knurled nuts securely.
The canopy should adjust for any irregu-
larity in the ceiling or Outlet box.

oosen the 2 set screws in yoke for
downrod to slip into yoke. Insert
downrod into yoke on top of the Fan
Body. Align the hole in the Downrod
with the hole in the Yoke. Insert the
Pin through the Yoke and Downrod
until the point appears on the other
side. Install the Keeper Pin
Tighten the 2 Set screws on the Yoke
once the downrod is in place.

Yoke
Cross Pin
Keeper
Pin
Thread canopy and yoke cover on down-
rod, Thread leadwires and safety cable
through the downrod. Follow inserts as
shown above.
Canopy Yoke cover
6=586,
)33

Install the light kit plate to the motor
by twisting clockwise and install the
screw removed from step 22 to the
light kit plate. Tighten the 3 screws
securely.

oosen 2 screws and remove 1 screw
from the light kit plate, save the
screw removed for later use.

Install the fitter to the light kit plate
by twisting clockwise, add 1 screw
removed from step 24 and tighten
the screws securely.

Remove the finial cap, hex nut, and
rubber pad from the fitter.

Place the glass onto the fitter as
shown.

Connect white wire from fan to white
wire from light fixture. Then plug
blue wire from fan to black wire from
light fixture by pushing together the
connectors.

Install 2 x60 watt Candelabra base
bulbs. Bulbs included. &!
<-83)4715/:0-.)5=133
8-9;3:15:0-.)531/0:990;::15/
,6=5;5:13:0-7867-8=)::)/-
6.*;3*9)8-159:)33-, !-9-::0-
31/0:9*?:;8515/6..:0-=)33
9=1:+0*8-)2-868*?8-46:-
!-73)+-*;3*9=1:0:0-+688-+:
=)::)/-*;3*9:;85:0-76=-865

Install the no light cover by using the
3 hex nut screws provided.
Use the hex nut driver to tighten the
3 hex nut screws.

oosen the 2 screws and remove 1
screw from the motor. Save the
removed screw for later use.

Remove 2 cardboards pre-installed
into the fan body. Install blades to
motor using the motor screws pro-
vided. Tighten screws and washers
by using the hex-nut driver provided.
 68159:)33):165=1:0
31/0:21:/6:69:-7

68159:)33):165
=1:06;:31/0:21:/6
:69:-7
Remove 3 screws from the motor.
Save the removed screws for later
use with light kit.


Place face plate over battery compartment and
buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snapping into place.
 HAND HE D INSTA
Install wall control unit to outlet box
using machine screws provided.
 WA MOUNT INSTA
Attach front cover to wall control
with screws provided. Snap battery
cover in place.

Install the rubber pad and hex
nut onto the threaded rod secur-
ing the glass.

Install the decorative finial nut to the
threaded rod by screwing on
securely.

Remove cover by snaping off from top or bot-
tom. Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready A23
/ GP 23A all 12V.Attach cover of remote by plac-
ing over buttons and snap the battery cover in
place.


!-46:-65:863#8)5941::-8-):;8-9
" Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
#!To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. ight will
maintain last setting if turned off.
!&!!%!" Depress rev button allow a few seconds for remote to
change rotation direction with fan running.
HIGH SPEED
MEDIUM SPEED
OW SPEED
FAN OFF SETTING
(Turns fan off only)
FAN REVERSE
(Press once to
change direction of
the fan)Fanmust be
running to reverse.
IGHT ON/OFF SET-
TING AND DIMMER
(Press and hold to
dim light infinitively)
ED IGHT

1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
$#)2-9;8-4)1576=-819:;85-,6..
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is
in the middle.
4.Make sure that shipping stabilizer tabs have been removed from motor.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
$#)2-9;8-4)1576=-819:;85-,6..*-.68--5:-815/9=1:+006;915/
4.If using an optional Ceiling Fan ight Kit, check to be sure the screws securing the glassware are finger
tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibration persists
from glass, remove glass and install a 1/4" wide rubber band on glass neck to act as an insulator.
Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls.
#$")"631,":):-<)81)*3-97--,+65:863
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this
period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in
Step #6 of Downrod Mount installation).
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junc-
tion box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a
point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to ceilng.
Keeping measure within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat
for each blade. If all blade levels are not equal, you can adjust blade levels by the following procedure.
To adjust a blade tip down, insert a washer (not supplied) between the blade and blade holder at the
screw closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the blade and
blade holder at the two screws farthest from the motor. Reverse the position of the washer if blades
mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the
weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
&!<-83)4715/:0-.)5=1338-9;3:15:0-.)531/0:990;::15/,6=5;5:13:0-
7867-8=)::)/-6.*;3*9 )8-159:)33-, !-9-::0-31/0:9*?:;8515/6..:0-=)339=1:+0
*8-)2-868*?8-46:-!-73)+-*;3*9=1:0:0-+688-+:=)::)/-*;3*9:;85:0-76=-865
$#)2-9;8-4)1576=-819:;85-,6..*-.68--5:-815/9=1:+006;915/
&!-.68-)::-47:15/:68-73)+-:0-.;9-4)2-9;8-:0-4)1576=-819:;85-,6..:6
:0-.)5!-73)+-653?=1:0))47.;9-;9-191591,-:0-+)567?65:0-*3;-=18-:68-46:-
8-+-1<-87;90)5,:=19::0-+)7:667-5:0-.;9-+)9-
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not
work:
TROUB E SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our
Customer Service Center at the number printed on your parts list insert sheet.
&)8515/-.68-9-8<1+15/68+3-)515/;51:"=1:+076=-86..):"-8<1+-7)5-3)5,36+29-8<1+-,19+655-+:15/
4-)59:678-<-5:76=-8.864*-15/9=1:+0-,65)++1,-5:)33?&0-5:0-9-8<1+-,19+655-+:15/4-)59+)556:
*-36+2-,9-+;8-3?.)9:-5)786415-5:=)8515/,-<1+-9;+0)9):)/:6:0-9-8<1+-7)5-3
Trouble Suggested Remedy
Customer Service Center:
301 West Washington St.
Riverside, NJ 08075
1-800-519-4092
www.montecarlofans.com

!( 
T('&'(%
;@A?B0A6<;@=<B?9T6;@A.99.A6<;1TB;
C2;A69.A2B?12=9.3<;1
#<61@A<A.91B
C2;A69.A2B?
47# $$ *7.*;*39.1&9*:7
!  !"!
389&11&9.43&;*(4:
8&381*1:2.3&.7*

C.;A12=?<0M12?J9V6;@A.99.A6<;1BC2;A69.A2B?0<B=2G
920<B?.;A.B;6C2.B1B=.;;2.B1V2;A?M21VM920A?606AM2A
C2??<B6992G9216@=<@6A6312@20A6<;;2:2;A=<B?MC6A2?>B2
920<B?.;A;2@<6A/?.;05M.00612;A2992:2;A&6C<B@;2
=.?C2;2G=.@JC2??<B6992?9216@=<@6A6312@20A6<;;2:2;A
=9.02G@B?92=.;;2.B1V2;A?M21VM920A?606AMB;2=.;0.?A2
<BB;2MA6>B2AA212:6@22;4.?12/62;C6@6/92
C.;A1V6;@A.992?02C2;A69.A2B?CM?6362G>B29./<PA212
@<?A62120<B?.;A2@A/62;0<;;20AM2J9.05.?=2;A21B
/KA6:2;A#<B?MC6A2?92@?6@>B2@1V6;02;1621VM920A?<0B
A6<;<B1V.00612;A:<;A2G92C2;A69.A2B?B;6>B2:2;AJ
B;2/<PA212@<?A62120<B?.;A<BJB;@F@AN:212@B=
=<?A=<BC.;A@B==<?A2?92=<61@1BC2;A69.A2B?V2;@2:/92
12:<;A.421<6A=<BC<6?@B==<?A2?.B:<6;@84

(A696@2G9./<PA212@<?A62120<B?.;A2;:MA.9=<BC.;A
@B==<?A2?92=<61@1BC2;A69.A2B?84C.;A12
?2962?92C2;A69.A2B?J9./<PA212@<?A62120<B?.;A
.@@B?2GC<B@>B202992062@A=.?3.6A2:2;A.AA.05M2.B
:<6;@2;12BE=<6;A@JB;2=6N021205.?=2;A21B=9.
3<;1B;2/<PA212@<?A62120<B?.;A:.9.AA.05M2
=?<C<>B2?.12@@20<B@@2@1BC2;A69.A2B?"9.1.8*?
:3.6:*2*391*8;.8+4:73.8&;*(1*'4E9.*7)*847
9.*)*(4:7&39

V6;@A.99.A6<;2A920K/9.42M920A?6>B21<6C2;AOA?22EM0BAM@=.?B;2<B=9B@62B?@=2?@<;;2@>B.9636M2@0<;3<?:M:2;AJA<B@92@0<12@2A;<?:2@
!&!#.==960./92@F0<:=?6@9.0<;@A?B0A6<;.;A66;02;162
!VBA696@2?02AA2B;6AM>B2129.:.;6N?2=?MCB2=.?923./?60.;A&6C<B@.C2G12@>B2@A6<;@C2B6992G0<;A.0A2?923./?60.;A
(;23<6@9V2;@2:/9212@369@?.00<?1M@02BE061<6C2;AOA?2@M=.?M@92/?.;052:2;A12:6@22;A2??22A@<;0<;1B0A2B?MA.;A1VB;0RAM129.
/<PA212?.00<?12:2;A2A920<;1B0A2B?;<;?296MJ9.A2??2129V.BA?20RAM1202AA212?;6N?2
C.;A120<::2;02?9V6;@A.99.A6<;1BC2;A69.A2B?0<B=2?920<B?.;A.BA./92.BM920A?6>B20<??2@=<;1.;A2AC2??<B6992?92@16@=<@6A63@120<B=B?2
12@2?C602.36;1V2:=O052?9.?2:6@2.00612;A29921B0<B?.;A<?@>B292@16@=<@6A63@120<B=B?2120<B?.;A;2=2BC2;A=.@OA?2C2??<B699M@.==<@2?
.C20@<6;B;16@=<@6A631V.C2?A6@@2:2;A/62;C6@6/92A29>BVB;2MA6>B2AA2@B?92A./92.BM920A?6>B2
#?B12;026?2A<BA2@92@6;@A?B0A6<;@2A0<;@269@12@M0B?6AM.C.;A1V6;@A.992?C<A?2;<BC2.BC2;A69.A2B?HAB162?92@@05M:.@6;09B@1.;@9V2:/.9
9.42
.6?2.AA2;A6<;12;2=.@2;1<::.42?920K/9.42M920A?6>B2<B.BA?2@2?C6020.05M9<?@129.=?.A6>B212A?<B@.B:B?<B.B=9.3<;1
&V.@@B?2?>B29V2;1?<6A05<6@6=<B?9V6;@A.99.A6<;=2?:2A.BE=.92@1BC2;A69.A2B?12A<B?;2?@.;@</@A?B0A6<;2/<?1.??6N?212@=.92@1<6AOA?2
.B:6;6:B:J=621@:NA?2@1B@<9
''!'"!! "!'%$(&(%&"Y'&%"% !'!$(!'$( "!'V(!)!''(%+&'#% &#<B?9.
?M1B0A6<;12@?6@>B2@1V6;02;1621205<0@M920A?6>B2@<B12/92@@B?2@0<?=<?2992@6;@A.992?@B?B;2/<PA212?.00<?12:2;A<BB;@F@AN:212@B=
=<?A.002=A./92=<B?B;C2;A69.A2B?(A696@2GB;6>B2:2;A92@C6@3<B?;6@.C2092/<PA62?12@<?A62120<B?.;A2:<;A.421<6A@B==<?A2?.B:<6;@
9/@84
!2=.@=962?92@=<?A2=.92@.B0<B?@129V6;@A.99.A6<;@B?92:<A2B?129VM>B696/?.42<B1B;2AA<F.42!2=.@6;@M?2?120<?=@MA?.;42?2;A?292@
=.92@2;:<BC2:2;A
<?@129.36E.A6<;12@@B==<?A@12@B@=2;@6<;;VBA696@2?>B29.>B6;0.6992?623<B?;62.C209./<PA212?.00<?12:2;A
#<B?9.?M1B0A6<;12@?6@>B2@1V6;02;162<B1205<0@M920A?6>B2@;2=.@BA696@2?02C2;A69.A2B?.C20B;16@=<@6A63M920A?<;6>B2120<;A?R92129.
C6A2@@2<BJB;20<::.;1212C.?6.A6<;129.C6A2@@2
21M/6A2;.6?120<:/B@A6<;?2>B6@=<B?923<;0A6<;;2:2;A2;A<BA2@M0B?6AM1VM>B6=2:2;A@.96:2;AM@=.?1B0<:/B@A6/92=2BAOA?2.3320AM
=.?9.:6@22;:.?0521202AA2B;6AM&B6C?292@16?20A6C2@2A.==96>B2?92@;<?:2@12@M0B?6AM6;16>BM2@=.?923./?60.;A1VB;A29M>B6=2:2;A
0<::202992@0<::B;6>BM2@=.?9V@@<06.A6<;!.A6<;.92129.#?<A20A6<;0<;A?292@;02;162@!#2A=.?92@;4M;62B?@129V@@<06.A6<;
:M?60.6;21B5.B33.42129.%M3?64M?.A6<;2A129V6?96:.A6@M&%2A=.?92@.BA<?6AM@?2@=<;@./92@12@0<12@9<0.BE
C.;A1V23320AB2?92@2?C602129VB;6AM<B129.;2AA<F2?0<B=2?920<B?.;A.BA./92.BM920A?6>B20<??2@=<;1.;A2AC2??<B6992?92@C2??<B6992?92@
16@=<@6A63@120<B=B?212@2?C602.36;9.?2:6@2.00612;A29921B0<B?.;A<?@>B292@16@=<@6A63@120<B=B?2120<B?.;A;2=2BC2;A=.@OA?2C2??<B69
9M@.==<@2?.C20@<6;B;16@=<@6A631V.C2?A6@@2:2;A/62;C6@6/92A29>BVB;2MA6>B2AA2@B?92A./92.BM920A?6>B2
6?20A6<;1B39BE1V.6?A2:=M?.AB?205.B126;A2??B=A2B?J4.B05239BE12@02;1.;AA2:=M?.AB?23?<6126;A2??B=A2B?J1?<6A239BE.@02;1.;A
 !!
''!'"!&()%&"!&&!%H(%&%&$(&V!!
VH'%"('"!"(&&(%
   @"!@
"! "
'<B?;2C6@0?B063<?:2<B=2369@#6;02@@0./2.B
M:<;A2?9V5M96022;?2A6?.;A92@C6@
<;@2?C2?92@C6@=<B?B;[email protected]B9AM?62B?
%2A6?2?9.?<;129922;=9.@A6>B22A9.72A2?

%2:2AA?29V5M96022;=9.022;9.36E.;A
.C2092@C6@?2A6?M2@9<?@129VMA.=2
62;@2??2?92@C6@


&B@=2;12G92C2;A69.A2B?:<;AM12=B6@92@B==<?A12
@B@=2;@6<;6;@A.99M.B=9.3<;1J9VMA.=2=?M0M12;A2
@@B?2GC<B@>B292C2;A69.A2B?2@A/62;1?<6A.6A2@=6C
<A2?92C2;A69.A2B?7B@>BVJ02>B29.9.;4B2AA21B@B==<?A
12@B@=2;@6<;@V2;4.421.;@9.32;A2129.?<AB92129.
A642C2?A60.922062:=O05292/KA61BC2;A69.A2B?12
=6C<A2?9<?@>B292@9.:2@@<;A2;:<BC2:2;A

%M492G92@0<::BA.A2B?@#@B?9VM:2AA2B?12AM9M0<:
:.;122A@B?92?M02=A2B?12AM9M0<::.;12@B?92@:O:2@
0<::.;12@2062@A</964.A<6?2@6C<B@C<B92G>B292@12BE
B;6AM@0<::B;6>B2;A0<??20A2:2;AV.BA?2@C2;A69.A2B?@
=2BC2;AOA?2?M49M@@B?B;M:2AA2B?2;?M49.;A92@12BE
?M02=A2B?@@B?92@:O:2@0<::.;12@>B29VM:2AA2B?&6
C<B@.C2G=9B@62B?@C2;A69.A2B?@0<:=<?A.;A92B?=?<=?2
M:2AA2B?C<B@=<BC2G?M492?92@0<::BA.A2B?@#@B?163
3M?2;A2@=<@6A6<;@=<B?=<BC<6?92@0<::.;12?@M=.?M:2;A

#<B?92:<;A.4212@A6;M.B.;.1.>B202@<6A@29<;9.
:MA5<1212@B@=2;@6<;2;0.@A?M2<B@29<;9.:MA5<1212
9.A642C2?A60.92920K/9212@M0B?6AM1<6AOA?26;@A.99M
1.;@92@=<BA?2@129.05.?=2;A21B/KA6:2;AJ9V.61212@
C6@J/<6@JAOA20.??M2120:3<B?;62@J02A2332A
@@B?2GC<B@>B29<?@>B2920K/9212@M0B?6AM2@A2;A6N?2
:2;A1M=96M92@369@120<;;2E6<;@<;A=9B@9<;4@>B292
0K/922A>BV69@;2@<;A@<B:6@J.B0B;233<?A12A2;@6<;
<;A.4212@A6;M.B.;.1.B;6>B2:2;A
0K/9212@M0B?6AM
)6@J/<6@JAOA20.??M2
0K/9212@M0B?6AM
?<;12992
)6@J/<6@JAOA20.??M2
?<;1299212/9<0.42
#9.02G92@=<?A2=.92@@B?92@=.92@2;.964;.;A92@A?<B@
1205.>B2=<?A2=.92.C2092@A?<B@1205.>B2=.92
@@B?2GC<B@>B2920RAM129.=.92>B2C<B@@M920A6<;
;2G2@AA<B?;MC2?@92/.@;@A.992GC6@2A92@?<;
12992@2;36/?2@J9V.??6N?2129.=.920<::26;16>BM
&2??2G92@C6@J3<;1%M=MA2G02=?<02@@B@3<6@
7B@>BVJ02>B2C<B@.F2G.@@2:/9MA<BA2@92@=.92@

;@A.992G92?M02=A2B?J16@A.;02@B?
92@B==<?A

#?M=.?2G=<B?920K/9.42

.6?2920K/9.420<::26;16>BM=?M0M12::2;A
2369/9.;01BC2;A69.A2B?1<6AOA?2?.00<?1M.B369
/9.;0129.AM9M0<::.;12:.?>BM!%.00<?12?
92369;<6?1BC2;A69.A2B?.B369;<6?129.AM9M0<:
:.;12:.?>BM2A92369/9.;0129.:.6@<;.B369
/9.;0129.AM9M0<::.;12:.?>BM!
%.00<?12?92369;<6?129.:.6@<;.B369;<6?129.
AM9M0<::.;12:.?>BM2A?.00<?12?A<B@92@
369@12:6@2JA2??2C2?A@.B36912:6@2JA2??212
9.:.6@<;
 )2;A69.A2B? .6@<;
/9.;0
;<6?
C2?A@
/9.;0
;<6?
3B@6/92
/92B
M492G92@0<::BA.A2B?@#@B?9VM:2AA2B?12AM9M0<:
:.;122A@B?92?M02=A2B?12AM9M0<::.;12@B?92@
:O:2@0<::.;12@2062@A</964.A<6?2@6C<B@C<B92G
>B292@12BEB;6AM@0<::B;6>B2;A0<??20A2:2;A
V.BA?2@C2;A69.A2B?@=2BC2;AOA?2?M49M@@B?B;M:2A
A2B?2;?M49.;A92@12BE?M02=A2B?@@B?92@:O:2@
0<::.;12@>B29VM:2AA2B?&6C<B@.C2G=9B@62B?@
C2;A69.A2B?@0<:=<?A.;A92B?=?<=?2M:2AA2B?C<B@
=<BC2G?M492?92@0<::BA.A2B?@#@B?1633M?2;A2@
=<@6A6<;@=<B?=<BC<6?92@0<::.;12?@M=.?M:2;A
 <::BA.A2B?@#
129VM:2AA2B?12
AM9M0<::.;12
20<::BA.A2B?#12
AM9M0<::.;122@A@6ABM
2;5.BA1BC2;A69.A2B?
;@B6A26;@A.992G92@M0?<B@:<92AM@
0<::2699B@A?M&2??2G92@M0?<B@:<92AM@
J3<;1.4.?;6AB?212C?.6A=<BC<6?@2
0<;3<?:2?JA<BA26??M4B9.?6AM1B=9.3<;1
<B129./<PA212@<?A62120<B?.;A

2@@2??2?92@12BEC6@12/9<0.422AM0?<B@
7B@>BVJ02>BV69@;2@<62;A=9B@=.9=./92@J9V6;
AM?62B?129.05.=2;@M?2G9.A642C2?A60.92
1.;@9.0B9.@@2@B?9.=.?A62@B=M?62B?21B/KA6
1BC2;A69.A2B?964;2G92A?<B=?.A6>BM@B?9.
A642C2?A60.92.C2092A?<B=?.A6>BM1.;@9.
0B9.@@2;@M?2G9.4<B=6992JA?.C2?@9.0B9.@@2
2A9.A642C2?A60.927B@>BVJ02>B29.=<6;A2
?M.==.?.6@@2129V.BA?20RAM;@A.992G9.
4<B=699212C2??<B699.42
&2??2G92@C6@@6ABM2@@B?9.
0B9.@@2B;23<6@>B29.A642C2?A60.92
2@A2;=9.02

974:57&9.6:B
(:1&88*8:7
,4:5.11*)*
;*774:.11&,*
692A2G9.0<BC2?AB?212C2??6N?22A12
7<B4@B?921<D;?<192@369@123692A92
0K/9212@S?2AM=.?921<D;?<1&B6C2G
92@6;@2?A6<;@0<::2:<;A?M0612@@B@
#*77.*7*
4:1**
!.,*
(4:;*79:7*):/4:,
