Monte Carlo Fan Company 5DKR52XXD Series Instruction manual

Owner’s Guide and Installation Manual
Total fan weight with light kit
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
Attach sales receipt to this card and retain as yourproof of purchase
To register your fixture, please visit our website www.montecarlofans.com
5DKR52XXD Series Fan
UL Model NO. : MC1207
11.9 kgs
26.18 lbs

Cautions and Warnings
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RK manufac-
tured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any other solid state fan speed control device, or variable
speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Note: Suitable for use in damp locations.
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
2
© 2011 Monte Carlo Fan Company 11/25/2012

3
© 2011 Monte Carlo Fan Company 11/25/2012
1 2 3
4 5 6
ON
OFF
ON
OFF
Before you begin installing the fan, Switch
power off at Service panel and lock
service disconnecting means to prevent
power from being switched on
accidentally. When the service
disconnecting means cannot be locked,
securely fasten a warning device, such
as a tag, to the service panel.
Before installing this fan make sure the
outlet box is properly installed to the
house structure. To reduce the risk of
fire, electric shock, or personal injury,
mount to outlet box or supporting system
acceptable for fan support.
(Mounting must support at least 35 lbs.)
Use metal outlet box suitable for fan
support and use only the screws provided
with the outlet box (must support 35
lbs). Before attaching fan to outlet box,
ensure the outlet box is securely fastened
by at least two points to a structural
ceiling member ( a loose box will cause
the fan to wobble). Remove the two outlet
box screws provided with the box,
aligning the holes of the mounting
bracket with the holes of the outlet box.
Reinstall the 2 outlet box screws
securely.
Partially loosen downrod set screws from
yoke at top of motor assembly.
Remove preassembled Keeper pin and
cross pin from downrod.
Note: Refer to installation step 22 about
reverse switch with airflow directions.
Place downrod over canopy, decorative
kit and yoke cover. Thread lead wires and
safety cable from motor assembly
through downrod.
Slip downrod into motor housing yoke,
aligning holes and install cross pin and
keeper pin.
Insert cross pin through yoke and downrod
until point appears on the other side, and
insert keeper pin on cross pin.
Pull the downrod up tight against the cross
pin, and then evenly tighten the downrod
set screws on motor housing yoke.
Place yoke cover and decorative kit on top
housing of fan.
Warning: Cross pin and keeper pin must
be installed securely, failure to install them
will result in serious injury.
Yoke cover
Canopy
Downrod
Mounting bracket
Downrod
Cross pin
Keeper pin
Decorative kit
Cross pin
Keeper pin
Reverse switch

4
© 2011 Monte Carlo Fan Company 11/25/2012
7 8 9
10 11 12
Install ball end of downrod into mounting
bracket opening. Align (engage) slot on
ball with tab on mounting bracket.
Warning: Failure to align slot on ball with
tab may result in serious injury.
For Canadian installation and for USA fan
and light kit combinations over 35 lbs, in
both flush and downrod modes the safety
cable must be installed into the house
structure beams using 3” lag screws,
washers and lock washers provided.
Make sure that when the safety cable is
fully extended the lead wires are longer
than the cable and no stress is placed on
the lead wires.
Set dip switches on the Remote
Transmitter and Remote Receiver to the
same settings. This must be done so the
units will communicate properly. If you
have other fans you can set to control
from one Transmitter by setting
receivers the same as the Transmitter. If
you have more than one fan with remote,
you can set the dip switches to different
positions to have separate control.
Make wire connections using wire
connectors provided as indicated above.
White from fan to White from remote
marked N. Blue from fan to Blue from
remote marked light. Black from fan to
Black from remote marked L. White from
house to White from remote marked AC
N. Black from house to Black from
remote marked AC L. Connect all green
grounded wires to Grounded wire from
House. Make sure that no filaments are
outside of the wire nuts.
Insert the remote receiver into mounting
bracket.
Lift Canopy, allowing the 2 studs to
protrude through the canopy.
Install knurled nuts provided and tighten
the knurled nuts securely. The canopy
should adjust for any irregularity in the
ceiling or outlet box.
Make sure the studs protruding from the
bottom of the Mounting bracket are
installed with threads all the way through
the bracket.
Install blade bracket with blade by 3
blade screws and washers provided.
Tighten securely. Repeat this process for
remaining blades.
White
White
White
Blue
Black
Black
Black
SAFETY CABLE INSTALLATION
ON
Dip switches
Lag screw
Safety cable
Washer
Lock washer
Blade
Blade bracket
Receiver
Grounded
/Green
Downrod
Slot
Tab
Grounded
/Green
Grounded/Green
Green
Wall switch
Stud

5
© 2011 Monte Carlo Fan Company 11/25/2012
13 14 15
16 17 18
Insert blade assembly into the slot on
flywheel.
Install blade assembly with screws
provided, aligning each of the holes as
shown and tighten all screws securely.
Repeat this process for remaining blades.
Note: Make sure the blade bracket faces
downward.
Attach decorative frame onto the plate on
motor, threading the lead wires from fan
through the decorative frame and aligning
the keyhole slots on decorative frame
with the preassembled screws on the
plate. Twist clockwise till lock. Reinstall
the screw removed in step 14. Tighten all
screws securely.
Loosen 2 and remove 1 preassembled
screw from the plate on decorative
frame. Save screw for later use.
Connect white wire from fan to white wire
from light fixture and then connect blue
wire from fan to black wire from light
fixture.
Attach light fixture onto the plate on the
decorative frame, aligning the keyhole
slots on the light fixture with the screws
on the plate and twist clockwise till tight.
Reinstall the screw removed in step 16.
Tighten all screws securely.
Loosen 2 and remove 1 preassembled
set screws from the plate on motor. Save
screw for later use.
Blade assembly
Light fixture
Lead wires
for light
Decorative frame
Blade bracket
Decorative frame
Plate
Plate on
motor

6
© 2011 Monte Carlo Fan Company 11/25/2012
19 20 21
22 23 24
Install 2 x 13W CFL medium base bulbs.
Bulbs included.
WARNING: USE MAXIMUM 13 WATTS
MEDIUM BASE LISTED
SBCFL(SELF-BALLASTED COMPACT
FLUORESCENT LAMP) ONLY, NOT DOING
SO COULD CAUSE THE UNIT TO
OVERHEAT AND LEAD TO POSSIBLE
DAMAGE TO THE PRODUCT.
Caution: Do not replace bulb until it
cools down.
Remove rubber washer, hex nut and finial
from light fixture. Save parts.
Attach glass onto light fixture. Install the
rubber washer, hex nut and finial removed
in step 20 to the thread rod by screwing
to secure the glass. Do not over tighten
the hex nut and finial.
Setting the reverse switch in the left hand
side will result in downward airflow and
setting the switch in the right hand side
will result in upward airflow.
Note: Reverse switch must be set either
completely Left or completely Right for
fan to function. If the reverse switch is set
in the middle position, fan will not
operate.
Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 /
Evereday A23 / GP 23A all 12V. Attach
cover of remote by placing over buttons
and snap the battery cover in place.
Place battery cover over battery
compartment and buttons. Place remote
over 2 pins on front cover. Attach cover
of remote by placing over 4 pins and
snapping into place.
Hex nut Hex nut
Finial
Finial
Glass
Battery cover
Battery
HAND HELD INSTALL
Right hand
side
(Reverse)
Left hand
side
(Forward)
Reverse switch
Rubber
washer
Rubber washer

7
© 2011 Monte Carlo Fan Company 11/25/2012
2625
Install wall control unit to outlet box using
machine screws provided.
Attach front cover to wall control unit with
screws provided. Snap battery cover in
place
WALL MOUNT INSTALL

8
© 2011 Monte Carlo Fan Company 11/25/2012
FAN SPEED: Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”.
LIGHT ON/OFF: To turn light on, press light button. To turn off press light button while light is on.
WARNING: This fixture is not dimmable. Use only with on/off switch. Do not use in conjunction fan/light dimmable remote controls
or light dimmers.
Note: If not using for long periods of time, remove battery to prevent damage to remote transmitter, and store the remote
transmitter away from excess heat or humidity
Remote Control Transmitter Features
MEDIUM SPEED
HIGH SPEED
LIGHT ON/OFF SETTING
(Press to turn light on/off)
LED LIGHT
LOW SPEED
FAN OFF SETTING
(Turn fan off only)

8
© 2011 Monte Carlo Fan Company 11/25/2012
Trouble Shooting
,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ
RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV
SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ
LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH
QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW
Warning%HIRUH VHUYLFLQJRU FOHDQLQJXQLW 6ZLWFKSRZHU RIIDW 6HUYLFHSDQHO DQGORFN VHUYLFHGLVFRQQHFWLQJ
PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH
ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO
&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV
&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ
CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII
,IWKLVIDQXVHVPDQXDO IRUZDUGUHYHUVH VZLWFKPDNH VXUHWKH VZLWFKLV SXVKHG¿UPO\
HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH
,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH
VXUHEDWWHU\LVHIIHFWLYH
&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG
&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW
&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK
RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ
CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ
&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH
6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV
$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU
DIWHUWKLVSHULRG
,IWKLV LVDGRZQURG PRXQWIDQPDNHVXUHWKHULGJH RQPRXQWLQJEUDFNHWHQJDJHVWKH
QRWFKLQWKHGRZQURGEDOO
0DNHVXUH WKDWFDQRS\ PRXQWLQJEUDFNHWRU PRXQWLQJSODWH DUHWLJKWHQHG VHFXUHO\WR
FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW
&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV
&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU
0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\
VHOHFWLQJD SRLQWRQWKH FHLOLQJDERYHWKHWLS RIRQHRI WKHEODGHV0HDVXUH WKLVGLVWDQFH
IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH
LVSRVLWLRQHGIRU PHDVXUHPHQW5HSHDWIRU HDFKEODGH ,IDOO EODGHOHYHOV DUHQRW HTXDO
\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW
DZDVKHU QRWVXSSOLHG EHWZHHQWKH EODGHDQG EODGHKROGHU DWWKH VFUHZFORVHVW WRWKH
PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH
KROGHUDWWKHWZRVFUHZVIDUWKHVWIURPWKHPRWRU 5HYHUVHWKHSRVLWLRQRIWKHZDVKHULI
EODGHVPRXQWIURPWRSRIEODGH
,IEODGHZREEOH LVVWLOOQRWLFHDEOHLQWHUFKDQJLQJWZR DGMDFHQWVLGHE\VLGHEODGHV FDQ
UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ
&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH
&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ
&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW
&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW
5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLILWLVFRQQHFWHGZLWKSOXJV
,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH
VXUHEDWWHU\LVHIIHFWLYH
CAUTION0DNH VXUHPDLQ SRZHULV WXUQHGRII EHIRUHHQWHULQJ VZLWFKKRXVLQJ DQGRU
FDQRS\
WARNING: 86(0$;,08:$7760(',80%$6(/,67('6%&)/6(/)%$//$67('&203$&7
)/825(6&(17/$0321/<12786,1*6%&)/:,//29(5+($77+(81,7$1'&$86('$0$*(727+(
81,7257+()$1:+,&+7+(81,7,6,167$//('72*(7+(5
,IIDQVRXQGVQRLV\
,IIDQZREEOHV
,IOLJKWGRHVQRWZRUN
,IIDQGRHVQRWVWDUW
Trouble Suggested Remedy

Nov.2012