Monte Carlo Fan Company 5TV52XXD Series Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proo o purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your ixture, please visit our website www.montecarlo ans.com
5TV52XXD Series Fan
Total an weight with light kit
UL Model No. : 5TV52
10.6 kgs
23.4 lbs

© 2013 Monte Carlo Fan Company 6/15/2013
2
WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G
READ A D SAVE THESE I STRUCTIO S
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA 70-1999), including
fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the
outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up
into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the
trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do ot Re-
move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign
object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
ever place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-
turer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the American Society for Heating, Refrigera-
tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlo ans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2013 Monte Carlo Fan Company 6/15/2013
3
Before you begin installing the fan, witch power off
at ervice panel and lock service disconnecting
means to prevent power from being switched on ac-
cidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warn-
ing device, such as a tag, to the service panel.
1
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
2
Thread safety cable through center
hole of the mounting plate. Thread
your house wires through center hole
also.These will be needed for wiring
of the fan.
4
ecurely attached the mounting plate
to the outlet box using two screws
supplied by the outlet box. se
metal outlet box suitable for fan
support (must support 35 lbs).
6
Place the decorative ring on the
motor housing.
3
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on the
other side of the outlet box.
9
Connect black and blue wire from fan to Black
or (Hot) wire from house. Connect White wire
from Fan to White (Neutral) wire from house.
Connect Ground leads from mounting bracket
and downrod to Ground lead from house.
Refer to Safety Tips section of manual.
8
Carefully lift the fan motor assembly
and engage the slot in the motor
housing with the hook on the mount-
ing plate so that the motor is se-
curely suspended.
7
For Canadian installation and for U A fan and
light kit combinations over 35 lbs, in both flush
and downrod mode the safety cable must be in-
stalled into the house structure beams using the
3” lag screws provided. Make sure that when
the safety cable is fully extended the leadwires
are longer than the cable and no stress is placed
on the leadwires. Note:If Installing The econd-
ary upport afety Cable in the U. ., Do Not Re-
move Knockouts In The Outlet Box.
5afety cable installation
Safety Cable
Lag Screw
Lag Screw
Safety Cable
Washer
Lock Washer

© 2013 Monte Carlo Fan Company 6/15/2013
4
Lift the motor housing up aligning the L
shape holes with the screws and
washers on the mounting plate. Turn the
housing clockwise to hold in position. In-
stall the other two screws and washers
previously removed securely.
11
Loosen the two screws and washers
across from each other on the ridge
of the mounting plate. Remove the
other two screws and lock washers.
ave for later use.
10
Lift the decorative ring up and twist
clockwise till tight.
12
Check the motor for shipping stabiliz-
ers and remove if present. Attach
blades using screws and washers in
hardware pak. Tighten screws se-
curely.
13
Loosen 2 screws and remove 1 screw
from motor plate. ave removed
screw for use later.
14
Connect plug from fan to switch
house plug.
16
Install by twisting clockwise, add 1
screw removed step 14 to switch
housing plate. Tighten the 3 screws
securely.
15
Connect white wire from fan to white
wire from light fixture. Then plug
blue wire from fan to black wire from
light fixture.
18
Loosen the pre installed screws of
switch housing plate.
17

© 2013 Monte Carlo Fan Company 6/15/2013
5
Install 3 screws to install light pan.
19
For fan with light kit go
to step 20-21 to
finish.
For fan without light kit
go to step 22.
Attach glass by locating dimples in
light fixture with the groves in glass
and twisting clockwise till tight.
21
Attach the non light cover by locating
dimples in the light fixture with the
grooves in the non light kit cover and
twist clockwise till tight. WARNING:
Make sure light bulb is not installed
when using this cover.
22
Install 75 watt halogen bulb. Do not touch
bulb surface as oily residue from skin can
cause the bulb to explode. Bulb Included.
WARNING: Over lamping the fan
will result in the fan lights shut-
ting down until the proper
wattage of bulbs are installed.
Reset the lights by turning off the
wall switch, breaker,or by remote.
Replace bulbs with the correct
wattage bulbs, turn the power on.
20

© 2013 Monte Carlo Fan Company 6/15/2013
6
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble hooting
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, instal-
lation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experi-
ence any faults, please check this Trouble hooting Chart. If a problem cannot be remedied, or you are
experiencing difficulty in installation, please call our Customer ervice Center at the number printed on
your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock serv-
ice disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Trouble Suggested Remedy
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Check to make sure the dip switches from the transmitter and receiver are set on the
same frequency.
CA TION: Make sure main power is turned off
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are
tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against
each other or against the interior wall of the switch housing.
CA TION: Make sure main power is turned off before entering switch hous-
ing.
4. ome fan motors are sensitive to signals from olid tate variable speed controls.
DO NOT SE a Solid State variable speed control.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disap-
pear after this period.
1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the
notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junc-
tion box and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level
by selecting a point on the ceiling above the tip of one of the blades. Measure this dis-
tance from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the
next blade is positioned for measurement. Repeat for each blade. If all blade levels are
not equal, you can adjust blade levels by the following procedure. To adjust a blade tip
down, insert a washer (not supplied) between the blade and blade holder at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the
blade and blade holder at the two screws farthest from the motor. Reverse the position
of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades
can redistribute the weight and possibly result in smoother operation.
1.Check wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CA TION: Make sure main power is turned off before entering switch hous-
ing.
WARNING: Over lamping the fan will result in the fan lights shutting down
until the proper wattage of bulbs are installed. Reset the lights by turning off
the wall switch, breaker,or by remote. Replace bulbs with the correct wattage
bulbs, turn the power on.

Jan.2012 Update customer service phone number
Jun.2013 Update for CUL regulation