Monte Carlo Fan Company 8ATR44XXD-L Series Instruction manual

Owner’s Guide and Installation Manual
Attac sales receipt to t is card and retain as your proof of purc ase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your fixture, please visit our website www.montecarlofans.com
8ATR44XXD-L Series Fan
Total fan weig t wit lig t kit
UL Model No. : AC-40448
14.3kgs
31.5 lbs

© 2011 Monte Carlo Fan Company 3/2/2012
2
WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G
READ A D SAVE THESE I STRUCTIO S
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do ot Re-
move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manufac-
tured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
ever place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 3/2/2012
3
Insert clevis pin through yoke and
downrod and secure with keeper pin.
(see inset)
Before you begin installing the fan, witch power off
at ervice panel and lock service disconnecting
means to prevent power from being switched on ac-
cidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warn-
ing device, such as a tag, to the service panel.
Install 4 x 15 watt candelabra tor-
pedo shape bulbs.
1
46
Loosen screw holding half ball and
remove pin from downrod. Thread
wires and safety cable through down-
rod and insert downrod into motor
yoke.
5
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
Install the Mountiing Bracket to the
Outlet box. Use only the screws
provided with the outlet box.
3
2
7
Tighten both yoke set screws and
lock nuts to further secure downrod.
8
Install upper glass over downrod
onto fan body.
9
Install canopy over downrod. Cau-
tion: Replace pin and ball onto down-
rod.

© 2011 Monte Carlo Fan Company 3/2/2012
4
Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on the ball
engages the ridge in the mounting bracket. This
will allow hands-free wiring.
11
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on the
other side of the outlet box.
16
Raise the canopy up and align the
two holes in the canopy with the two
holes in the hanger bracket. ecure
with two screws provided.
17
10
Tighen set screw loosened in step 5.
Install remote receiver by sliding into opening in
the mounting bracket. Make sure that the dip
switches on the transmitter and the receiver are
set to the same positions.
14
Install 1 x 100 watt JD E-11 halogen bulb. Do
not touch bulb surface as oily residue from skin
can cause the bulb to explode. Bulb included.
WA NING: Over lamping the fan will re-
sult in the fan lights shutting down
until the proper wattage of bulbs are
installed. eset the lights by turning off
the wall switch, breaker,or by remote. e-
place bulbs with the correct wattage bulbs,
turn the power on.
18
et dip switches on the Remote Transmitter and
Remote Receiver to the same settings. This must
be done so the units will communcate properly. If
you have other fans you can set to control from
one transmitter by setting both receivers the same
as the transmitter. If you have more than one fan
with remote. You can set the dip switches to differ-
ent positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
13
white
black
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Orange from fan to Orange from remote
marked Light/up. Blue from fan to blue from
remote marked down light. Black from fan to
Black from remote marked L. White from
house to white from remote marked AC N .
Black from house to Black from remote
marked AC L. Connect all green ground wires
to Ground wire from House.
orange
blue
Green
white
black
House
Fan
15
fuses
For Canadian installation and for U A fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The econdary upport afety
Cable in the U. ., Do Not Remove Knockouts In
The Outlet Box.
12 afety cable installation
Safety Cable
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer

© 2011 Monte Carlo Fan Company 3/2/2012
5
Install glass to fan using the 3 ball
screws provided.
20
Install glass to fan.
19
Attach blade assembly to arms from
motor housing using screws and
washers provided. Tighten screws se-
curely.
21
Remove cover by snaping off from top or bot-
tom. Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready
A23 / GP 23A all 12V.Attach cover of remote by
placing over buttons and snap the battery cover
in place.
Place face plate over battery compartment and
buttons. Place remote over 2 pins on front cover.
Attach cover of remote by placing over 4 pins and
snaping into place.
23
22 HAND HELD IN TALL
Install wall control unit to outlet box
using machine screws provided.
24
Attach front cover to wall control
with screws provided. nap battery
cover in place.
25
WALL MOUNT IN TALL

© 2011 Monte Carlo Fan Company 3/2/2012
6
emote Control Transmitter Features:
FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGHT DIMME To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. Light will
maintain last setting if turned off.
FO WA D/ EVE SE Depress rev button allow a few seconds for remote to
change rotation direction with fan running.
HIGH PEED
MEDIUM PEED
LOW PEED
FAN OFF ETTING
(Turns fan off only)
FAN REVER E
(Press once to
change direction of
the fan)Fanmust be
running to reverse.
UPLIGHT ON/OFF ET-
TING AND DIMMER
(Press and hold to dim
light infinitively)
LED LIGHT
DOWNLIGHT ON/OFF
ETTING AND DIMMER
(Press and hold to dim
light infinitely)

© 2011 Monte Carlo Fan Company 3/2/2012
7
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Check to make sure the dip switches from the transmitter and receiver are set on the same
frequency.
CAUTION: Make sure main power is turned off
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other
or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4. ome fan motors are sensitive to signals from olid tate variable speed controls. DO NOT
USE a Solid State variable speed control.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box
and junction box is mounted firmly to ceiling joist.
5.Dynamic balancing involves ‘counter-weighting’. By using a small weight opposite to the
point of wobble, you can in almost all cases eliminate the wobble. The procedure requires
much trial and error, and a certain amount of patience to achieve the correct position of the
counterweight. A) Determine which fan speed causes the most wobble. This will almost always
be the highest speed. B) Turn the fan off. elect any one blade and place the balance clip half
way between the blade tip and blade holder, on the rear edge of the blade. Caution: Be care-
ful to stay clear of the blades when running. If the clip is not secure, injury may re-
sult from the clip flying off. C) Turn the fan on. Observe if the wobble is better or worse.
Turn the fan off and move the clip to the next blade. Do the same for all blades and note on
which blade the clip improves the wobble the most. D) Place the clip on the blade which
showed the most improvement and by trial and error move the clip in and out along the blade
to find the position which most improves the wobble. E) Remove the clip and discard. Once the
exact position is determined, place a weight on bottom of the metal blade holder on its center-
line. Press the weight firmly to ensure it is firmly attached to the blade holder. Add more
weight as needed to balance.
1.Check wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WA NING: Over lamping the fan will result in the fan lights shutting down
until the proper wattage of bulbs are installed.
eset the lights by turning off the wall switch, breaker,or by remote. eplace bulbs
with the correct wattage bulbs, turn the power on.
CAUTION: Make sure main power is turned off before entering switch housing.
WA NING: Before attempting to replace the fuse make sure the main power is turned
off to the fan. eplace only with a 3 amp fuse. (Fuse is inside the canopy on the blue
and orange wires to remote receive, push and twist the cap to open the fuse case).
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble hooting
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trou-
ble hooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our
Customer ervice Center at the number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means can-
not be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
Trouble Suggested emedy

Mar.2012 New format
May.2013 Update for CUL regulation