Monte Carlo Fan Company ESSWC-10 Owner's manual

SAFETY INFORMATION AND GENERAL GUIDE
READ AND SAVE THESE INSTRUCTIONS
• Please read and understand this entire manual before attempting to assemble, install or operate
the product.
• Make sure that all electrical connections comply with local codes, ordinances, the National
Electrical Code and ANSI/NFPA 70. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
Warning : Before proceeding, be sure to shut off electricity at main switch or circuit breaker in
order to avoid electrical shock.
ESSWC-10 WALL TRANSMITTER
INSTALLATION AND OPERATION INSTRUCTION
Note : Fan installation must be complete including assembly of blades before testing wall control
unit.
Note: Refer to your Ceiling fan instruction manual for Safety and installation instruction.
This wall controller is to be used for the control of ceiling fan and fan light only.
Warning: Do not exceed maximum rating of the wall transmitter. Install the wall transmitter
away from excess heat or humidity
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com

Warning: Before proceeding, be sure to shut off electricity at
main switch or circuit breaker in order to avoid electrical shock.
Note: Before installing the wall transmitter, place it in OFF
position by pushing ON/OFF switch to the OFF.
Make series-wound connection for the wall transmitter with HOT
wire from house. Connect a black wire from wall transmitter to
the HOT wire and then connect the other wire of wall transmitter
to the LOAD wire in outlet box (Follow the instruction shown on
the labels on the lead wires from wall transmitter). Connect
white wire from fan to white (neutral) wire from house.
Connect green grounded wire to grounded wire from outlet box.
Install the wall transmitter to outlet box using machine screws
provided.
Attach wall plate to wall control unit with screws provided.
Note: Place the wall transmitter in ON mode when fan
installation is completed for operation.
The switch cover and wall plate can be replaced with almond
covers provided. Remove the switch cover by a finger and snap
the new one in place.
Wall Transmitter Installation and Wiring
Wall Transmitter Setting and operation
Wall
Box
Hot to
AC source
To load
Ground
Wall plate
Switch cover
Wall transmitter
ON
OFF
Receiver
Restore power to your fan to make learn function setting to pare the Transmitter
and receiver, press and hold the “OFF” button for at least 5 seconds. You must
press the ‘OFF” button within 60 seconds of restoring power to the fan.
Important: Only turn the power on for the fan which you would pair with the
transmitter and make sure to turn the power off for all other fans which use the
same remote controller.
Note : If the fan is installed with light (down light), light will twinkle twice then off.
The fan will start to run and begin the control setting process. The fan will run in
both directions for a total of approximately 3 minutes, then the fan will stop. The
control and speed setting process is complete and the fan is ready for use.
Note : If the power is on already, you must turn the power off for at least 5 seconds,
and then turn the power back for remote control setting.
Note: If you want to control the fan with another hand-held transmitter, make the
same setting. A fan can be controlled by 2 transmitters maximum.
The fan will again start to run control setting process when you make learn function
setting for the second transmitter. You may keep this setting process or you may
finish the setting process by turning the power off and turning power back.
Note: If use 2 wall-mounted transmitters, they have to be wire with series wound.
Recommend handling by an electrician.
Note: If you press wrong buttons, you must again turn power off and turn the power
back then reset learn function.
“OFF”
ON
OFF
2
6/2021
© 2021 Monte Carlo Fan Collections

REMOTE CONTROL SETTING and OPERATION
Press the button to get desired fan speed, Low to High and then High to Low
cyclically.
Press the OFF button to turn fan off. Fan speed will maintain last setting if
turned off.
Press this forward/reverse button to get desired airflow direction. Fan must be
running to reverse. It will take about 25 seconds for fan to slow down and
change rotation direction.
Light control button. Press this button quickly to turn light on or off. To dim
light, hold down the button, the light will cycle from bright to dim to bright until
button is released (when the controller is set in dimming mode). Light will
maintain last setting if turned off.
Refer to page 4 for dimming, non-dimming
setting.
Note
: Dimming function is not available if the controller is set at non-dimming
mode.
LED indicator against fan speeds below
The buttons on the remote control transmitter control the fan speed and light
as follows.
User Tips
1. If your fan is operating automatically after installation, it is still using the factory setting. Follow the settings for Learn Mode
above to reset.
2. If the fan or light isn’t working, reset power (turn the power off then turn the power back on) and follow the Universal Mode or
Learn Mode remote control settings.
3. If two or more fans in the same remote signal range are on the same power supply, they cannot be operated separately by
remote control. Use a separate power supply for each fan, such as an individual wall switch, and restrict the power supply to
only the fan which you are pairing with its transmitter in order to use the remote controller.
4. When the fan is turned on to oscillate in either forward or reverse direction, it may shudder briefly until fully engaged. This is a
normal operation for this fan; the shuddering will quickly cease as movement is engaged.
5. There might be other remote transmitters got the same code combination as the transmitter that you are using, you may
remove the code setting of the other transmitters by turn the power off and turn it back and then push and hold the “OFF” button
of the transmitter which you are using for at least 10 seconds. You must press the ‘OFF” button within 60 seconds of restoring
power to the fan.
Fan off
Minimum speed
Low speed
Medium low speed
Medium speed
Medium high speed
High speed
ON
OFF
3
6/2021
© 2021 Monte Carlo Fan Collections

REMOTE CONTROL SETTING (Dimming/Non Dimming)
Dimming, Non-Dimming Setting
The remote controller is set with dimming function at factory.
If you would make the light with on/off feature (non-dimmable). Set the fan at
third speed (medium low speed), press “OFF” and “Light” buttons at the same
time for more than 3 seconds. It has to be handled with fan/receiver power on.
Operate the same process may switch it back to dimming function and vice
versa.
In the dimming mold, it is light dimmable selection and it is to be used with
dimmable luminaries. Press and hold the button to dim the light. The light will
cycle from bright to dim to bright until button is released. Light will maintain
the last setting if turned off. Press and release the button quickly may turn light
on/off.
In on/off (non-dimming mold), it is for light ON/OFF only (non-dimming function).
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
ON
OFF
4
6/2021
© 2021 Monte Carlo Fan Collections

Jun.2021