Montigo H Series Instruction Manual
xg0227 - 112718
Installation & Maintenance Manual
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
— WHAT TO DO IF YOU SMELL GAS
phone. Follow the gas supplier’s instructions.
department.
DIVINE
Pier, Bay & Corner
INDOOR DIRECT VENT GAS FIREPLACE
H38PFNI-2 NG Traditional
H38PFLI-2 Propane Traditional
HL38PFNI-2 NG Linear
HL38PFLI-2 Propane Linear
H38PRNI-2 NG Traditional
H38PRLI-2 Propane Traditional
HL38PRNI-2 NG Linear
HL38PRLI-2 Propane
Read and understand this manual. Improper installation, adjustment,
alteration, service or maintenance can cause serious injury, property
damage or even death. For assistance or additional information
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
must be installed for the protection of children and
other at-risk individuals.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for suture reference.
Notice
cautioN
DaNger
DaNger
H38CLNI-2 NG Left Traditional
H38CLLI-2 Propane Left Traditional
HL38CLNI-2 NG Left Linear
HL38CLLI-2 Propane Left Linear
H38CRNI-2 NG Right Traditional
H38CRLI-2 Propane Right Traditional
HL38CRNI-2 NG Right Linear
HL38CRLI-2 Propane Right Linear
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WarNiNg
2
General
xG0227 - 112718
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the
instructions laid out in this Installation, Operation and Maintenance
Manual and retain it for your future reference. Pay special attention
to all cautions, warnings, and notices throughout this manual
intended to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,
homeowner. All installation and service work should be performed
is being installed.
This installation, operation and maintenance manual is applicable
to the models described in Table 1. Refer to your rating plate to
verify included options.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
Vent assembly or glass doors.
Use of any component part not manufactured or approved by
Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation
Introduction
Safety Alert Key
Indicates a hazardous situation which, if
not avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates practices that are important, but
not related to personal injury.
DaNger
cautioN
WarNiNg
Notice
Figure 1 H38PFC, H38PRC, H38CL/CR Specications
MODEL
Natural Gas
Propane
Gas Rating (BTU hr)
Linear Burner
SIT Electronic Ignition
H38PFNI-2 X 34,000 X X
H38PFLI-2 X 32,000 X X
HL38PFNI-2 X 34,000 X X
HL38PFLI-2 X 32,000 X X
H38PRNI-2 X 34,000 X X
H38PRLI-2 X 32,000 X X
HL38PRNI-2 X 34,000 X X
HL38PRLI-2 X 32,000 X X
H38CRNI-2 X 34,000 X X
H38CRLI-2 X 32,000 X X
HL38CLNI-2 X 34,000 X X
HL38CLLI-2 X 32,000 X X
3
General
xG0227 - 112718
Contents
Safety Alert Key.................................................................................. 2
Introduction ....................................................................................... 2
Section A: Before You Begin ......................................................................................... 4
Installation Checklist........................................................................................................ 4
Standard Installation Checklist...................................................................................... 5
Section 1: Product Dimensions......................................................... 7
H38PR*I-2 Dimentions.................................................................................................... 7
H38PF*I-2 Dimentions .................................................................................................... 7
H38CL/CR*I-2 Dimentions ............................................................................................. 8
Section 2: Framing ............................................................................ 9
Framing dimensions ........................................................................................................ 9
PFC Shelf over the fireplace, Rear vent....................................................................... 9
PFC Shelf over the fireplace, Top vent......................................................................... 9
PRC Shelf over the fireplace, Rear vent....................................................................... 9
PRC Shelf over the fireplace, Top vent ........................................................................ 9
PRC or PFC Alcove above the fireplace....................................................................... 9
Corner Framing dimensions........................................................................................10
Shelf over the fireplace, Top vent...............................................................................10
Shelf over the fireplace, Rear vent .............................................................................10
Alcove above the fireplace ...........................................................................................10
Clearances........................................................................................................................11
Installing The Standoffs.................................................................................................11
Removing the Nailing Flange Extension....................................................................11
Section 3: Venting ............................................................................ 12
Section 3-1: Converting top/rear vent......................................................................12
Section 3-2: Installing a Roof Mounted Direct Vent Termination
............................................................................................................ 13
Section 3-2-1: Venting Layout .....................................................................................13
.........15
Section 3-3-1: Venting Layout: Wall Mounted Termination ........16
PRC & PFC Top Venting Graph....................................................................................16
PFC Rear Venting Graph ...............................................................................................17
PRC Rear Venting Graph...............................................................................................18
Corner Top Venting Graph...........................................................................................19
Corner Rear Venting Graph .........................................................................................20
Section 3-3-2.2: Alternate Venting Components 5"/8"..........................................21
.................................................... 22
Section 4: Wiring .............................................................................. 23
Legacy model wiring ......................................................................................................23
POD - Pilot on Demand.................................................................... 24
What is POD and CPI mode? .......................................................................................24
Remote Continuous Pilot (CPI) Selection .................................................................24
Installing the CPI Jumper Cable...................................................................................24
Section 5: Installing the gas line.....................................................25
Section 5-1: Fuel Conversion.......................................................................................25
Section 5-2: Gas Pressure ............................................................................................ 25
Section 5-3: GAS CONNECTION.................................................................................. 25
Section 6: Finishing .......................................................................... 26
Mantels & Surrounds .................................................................................................... 26
Fireplace Facing .............................................................................................................. 26
Finishing around the fireplace .................................................................................... 26
................................. 27
Removing the Screen..................................................................................................... 27
Replacement Screens.................................................................................................... 27
...................................
Removing the door ........................................................................................................ 28
Reinstalling the door...................................................................................................... 28
Section 9: Installing the Accessories.............................................. 29
H38ST Installing the Logs and Embers ..................................................................... 29
Installing the Firestones or optional Fireglass ........................................................ 29
Section 10: Start up Sequence ........................................................ 30
Standing (Continuous) Pilot Ignition (SIT 820)........................................................ 30
SIT Proflame 2 Electronic Ignition............................................................................... 31
Remote Operation ........................................................................... 32
Initializing the System for the first time .................................................................... 33
Operating the System for the first time.................................................................... 33
Temperature Indication Display.................................................................................. 33
Turn On the Fireplace ................................................................................................... 33
Remote-Flame Control.................................................................................................. 34
Room Thermostat (Remote Control Operation)..................................................... 34
Disabling Thermostat .................................................................................................... 35
Fan Speed Control.......................................................................................................... 35
Section 10: Cleaning and Maintenance ........................................ 36
General ............................................................................................................................. 36
Hi-Lo Burner Adjustment: (SIT 820). .......................................................................... 36
Hi-Lo Burner Adjustment: (Proflame 2)..................................................................... 36
Pilot Burner Adjustment. .............................................................................................. 36
Troubleshooting SIT 820............................................................................................... 37
Troubleshooting SIT Proflame 2 ................................................................................. 37
Replacement Parts ..........................................................................
Replacement Parts List - Standing Pilot.................................................................... 38
Replacement Parts List - SIT IPI Proflame 2............................................................. 38
Indoor fireplace in protected outdoor applications ............................................. 39
See through fireplace.................................................................................................... 39
Single sided fireplace..................................................................................................... 39
Appendix A: Venting Terminations................................................ 40
Appendix B: Warranty ..................................................................... 41
Appendix C: Amendment
4
General
xG0227 - 112718
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
Gas Branch to determine the need for a permit prior to starting the
is installed in compliance with the manufacturers instructions and all
applicable codes.
Installation Checklist
See Section 1, Dimensions and refer to the Framing Section 2 for
details.
Select the location of your termination and resulting vent run.
Your selected termination location must be the highest point in the
Direct Vent installation.
Should it be impossible to meet the venting requirements laid out in
Section 3: Venting, please contact a local Montigo dealer regarding
the use of a Montigo Power Vent.
Lay out the Vent run; calculating the required elbows and straight
Layout Electrical Requirements Refer to Section 4: Wiring, for Details.
Refer to Section 5: Installing the Gas Line, for details on the gas
connection and access.
Refer to local codes and guidelines for installation requirements.
and must conform to:
Installations in Canada must conform to the local codes or in
the absence of local codes to the current version of Natural Gas
and Propane Installation Code, CSA B149. Electrical installations
must conform to the local codes or, in the absence of local codes,
to the current version of Canadian Electrical Code, CSA C22.1.1
Installations in the USA must conform to the local codes or in
the absence of local codes to the current version of National
must conform to the local codes or, in the absence of local
codes, to the current version of the National Electrical Code,
of Massachusetts
Do not use this appliance if any part has been under water.
and to replace any part of the control system and any gas control that
has been under water
Due to high temperatures, the appliance should be located out of
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed for the
protection of children and other at-risk individuals
the appliance
The appliance should be inspected before use and at least annually
by a professional service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners, and circulating air
passageways of the appliance be kept clean
Notice
Notice
Notice
Notice Notice
Notice
Section A: Before You Begin
5
General
xG0227 - 112718
Standard Installation Checklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained within this
installation manual.
Customer Date Installed:
Install Address: Location of Fireplace:
Installer:
Model (circle one): H38PFNI-2, H38PFLI-2, HL38PFNI-2, HL38PFLI-2
, H38PRNI-2, H38PRLI-2, HL38PRNI-2, HL38PRLI-2
Dealer Phone:
Serial #:
YES NO IF NO, WHY NOT?
Appliance Install: Section 2
Framing complies with install manual.
Proper clearances have been maintained.
Venting: Section 3
Venting installed, fastened, and secured in place maintaining proper clearance.
Firestops installed.
Terminations installed and sealed in compliance with local building code.
Direct vent termination is highest point in vent assembly.
Unswitched power provided to the appliance PPO box.
Low voltage wire connected to dry contact wall switch (non-powered)*
Gas: Section 5
Proper appliance for fuel type.
Was a conversion performed?
Finishing: Section 6
Only non-combustible materials installed in non-combustible areas.
Clearances meet installation manual requirements
Appliance Setup: Section 7 through 9
Media, door, and screen installed according to install manual
Manual given to home owner.
Comments:
6
General
xG0227 - 112718
Rating Plate Sample
Figure 1.1 Rating Plate for IPI electronic ignition Figure 1.2 Rating Plate for IPI electronic ignition
LBA12xx - ANSI Z21.88-2016 Rating Plate Label
LB1223-V5.0 SIT IPI -with screen JUN 16.2014
Teklynx LabelView Demo
7
General
xG0227 - 112718
Section 1: Product Dimensions
Please review the Installation
Checklistforgeneralinformation
on preparing for a successful
in any location that maintains
proper clearances to air
conditioning ducts, electrical
wiring and plumbing. Safety, as
should be considered when
Select a location that does not
an accessible path for Direct
Vent installation.
1006
39 5
8"
1088
42 7
8"
816
32 1
8"918
36 3
16 "
123
413
16 "
628
24 3
4"
414
16 5
16 "
667
26 1
4"
203
8"
127
5"
520
20 7
16 "
440
17 5
16 "
675
26 9
16 "
1087
42 13
16 "
843
33 1
8"
85
33
8"
47
17
8"
68
21
2"
34
11
2"
29
11
8"
235
91
4"
67
25
8"
H38DF-PRC / HL38DF-PRC
DIMENSIONS TOLERANCES ARE IN:
METRIC - MM
1.6 MM
IMPERIAL - FRACTIONAL
1/16"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
November 30, 2017
DATE:
1007
39 5
8"
1079
42 1
2"
1043
41 1
16 "
839
33"
635
25"
77
31
16 "
185
75
16 "
216
81
2"
93
311
16 "
GAS
SUPPLY
POWER
SUPPLY
220
85
8"
127
5"
203
8"
600
23 5
8"
651
25 5
8"
1088
42 13
16 "1132
44 9
16 "
17
11
16 "
978
38 1
2"
636
25 1
16 "
123
47
8"
248
93
4"
H38DF-PFC / HL38DF-PFC
DIMENSIONS TOLERANCES ARE IN:
METRIC - MM
1.6 MM
IMPERIAL - FRACTIONAL
1/16"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
November 29, 2017
DATE:
General
xG0227 - 112718
996
39 3
16 "
1007
39 5
8"
102
4"
1072
42 3
16 "
630
24 13
16 "
152
6"
565
22 1
4"
644
25 3
8"
518
20 3
8"
204
8"
127
5"
177
7"
616
24 1
4"
87
37
16 "
360
14 3
16 "
844
33 1
4"GAS
SUPPLY
H38DF-CR / HL38DF-CR
DIMENSIONS TOLERANCES ARE IN:
METRIC - MM
1.6 MM
IMPERIAL - FRACTIONAL
1/16"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
November 29, 2017
DATE:
9
Installation
xg0227 - 112718
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed
Pier PFC: Frameintheenclosure
for the unit with framing
materials. The framed opening
Bay PRC: Frameintheenclosure
for the unit with framing
materials. The framed opening
deep.
Section 2: Framing
Framing dimensions
Figure 3.b Combustible Framing for shelves over the replace, Side vent.
Figure 3.b Combustible Framing for shelves over the replace, Rear vent.
Figure 3.b Combustible Framing for shelves over the replace, Top vent.
Figure 3.b Combustible Framing for shelves over the replace, Top vent.
Figure 3.b Non Combustible Framing with alcove above replace, Top Vent.
24 1/2”
40 3/4”
44”
41
23 3/4
44
33"
40¾" 23¾"
44"
41"
44"
24½"
33"
44"
44"
44"
39"
2"
44"
11" MIN.
11"
17½"
46" MIN.
46"
2" MIN.
1" MIN.
12" MAX.
1" MIN.
12" MAX.
17½" MIN.
1" MIN.
10
Installation
xg0227 - 112718
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed
Frame in the enclosure for the unit with framing
Approximate dimentions to center. For best results mount non-
Corner Left Corner Right
Corner Framing dimensions
Figure 3.b Combustible Framing for shelves over the replace, Rear vent.
Figure 3.b Combustible Framing for shelves over the replace, Top vent.
Figure 3.b Non Combustible Framing with alcove above replace, Top Vent.
43¾" 43¾"
44" 44"
25¼" 25¼"
59"
MIN.
1" MIN.
MAX.
44"
44" 39"
2"
13" MIN.
17½"
46"
1" MIN.
1" MIN.
11
Installation
xg0227 - 112718
Clearances
Installing The Standoffs
MODEL
Top - Rear
Top - Top
Header
Sides
Front
Rear
Venting - Top
Venting -
H*38PRC*I-2 11" 4" 0" 0" 1" 2" 1"
H*38PFC*I-2 11" 4" 0" 0" 2" 2" 1"
H*38C**I-2 13" 4" 5" 0" 2" 2" 1"
Figure 4. Combustible Wall Clearances
guidelines must be adhered to:
For Rear Vent applications, the minimum clearance is 1" from the rear of
materials.
For Top Vent applications, the minimum clearance is 1" from the rear
the underside of any combustible shelf materials.
1” clearance is maintained on sides and bottom of vent runs and 2”
above horizontal vent runs to any combustible material.
enclosure.
** Note: For mantel clearance, please refer to Section 6: Finishing
NON-Combustible material of the same thermal characteristics, ie:
in applications where the facing materials will not adhere to the metal
directions below:
8" clearance.
Figure 4.b Installing standos
STEP 1: Remove screws from top of the unit
STEP 2: Remove shell from the top of unit. Remove screws from
outer edge.
STEP 4: Remove the nailing flange extension from the unit.
Reinstall shell. Screw shell in place.
STEP 3: Remove shell from the top of unit. Remove screws from
outer edge.
12
Installation
xg0227 - 112718
Figure 5. Flue cover and collar removal, Top Vented replace.
Figure 5.b Flue cover and collar installation, Side Vented replace.
Flue Gasket
Flue Cover Plate
8” Outer Flue Collar
5” Inner Flue Collar
5”Inner Flue Collar
8”Outer Flue Collar
Flue Gasket
Flue Cover Plate
Section 3: Venting
Montigo supplies a variety of direct venting and termination options.
The direct vent termination location MUST be selected such that it is the
highest point in the venting assembly. It should also be selected such
that it provides the shortest vent run possible. Should it be impossible
to ensure that the termination is the highest point or to meet the
venting guidelines laid out below please contact your Montigo dealer
to discuss power venting options.
Notes For Planning Venting:
Ventingcan originate from the unitthroughthe top or throughtherear
Venting can terminate through the roof or through an exterior wall.
Refer to Appendix A - Termination Locations to ensure the planned
termination location is acceptable.
Once the termination location has been established, refer to the
appropriate section below for installation details
Silicone application is NOT required when joining Montigo vent
pipes and components.
Use the following instructions to convert a unit for side vent use:
as shown in Figure 5.
shown in Figure 5.
vent outlet. Fasten the cover with included hardware, as illustrated
Figure 5b.
Install the (5" and 8") collars to the Side vent outlet using the included
hardware, as illustrated Figure 5b.
Outer Flue Plate
5" Inner Flue Cover Plate
5" Inner Flue
Cover Plate
5" Inner Flue Collar
8" Outer Flue Collar
8" Outer Flue Collar
8" Outer Flue Cover Plate
Flue Collar
accommodate an installation. Use an alternative length to complete
your vent run.
Notice
13
Installation
xg0227 - 112718
Roof mounted terminations
terminations. See below.
This section applies to installations where the direct vent termination
will be roof mounted.
Section 3-2-1: Venting Layout
Selection of components and details of venting lay out should adhere
to the following guidelines:
The Vertical termination must be a minimum 2’ higher than where
shakes, etc). This distance should be measured from the high side of
(see Figures 8 to 8c).
See Appendix A for termination locations.
For a more detailed diagram of allowed termination locations, see
Appendix A.
may be made for vertical vent runs.
Ensure all horizontal runs are supported with a minimum of 3
supports per 10’ of venting.
Figure 6. Top vent, roof mounted termination with no oset in vent run.
Figure 6.b Top vent, Roof mounted with 1 oset (1 oset= two 90° bends).
Figure 6.c Top vent, Roof mounted with 2 osets (1 oset= two 90° bends).
Section 3-2: Installing a Roof Mounted Direct Vent
Termination
PVTK1 Termination
PVTK1 Termination
PVTK1 Termination
Storm collar
Storm collar
Storm collar
Support ring
Support ring
Support straps OR
Support ring and plates
Support ring and plates
Support plate
Support plate
Firestop
Firestop
Firestop
Firestop
Firestop
PEXT
PEXT-10
Adaptor
Flue
Collar
14
Installation
xg0227 - 112718
Figure 6.d Side vent, Roof mounted venting (1 = 90° bend).
Storm collar
Support plate
PVTK1 Termination
Support ring
PEXT Solid Sections
12"
max.
Firestop
Firestop
15
Installation
xg0227 - 112718
Figure 7. Installing a PTO4-F termination.
Figure 7.b Installing a PTO termination with the MSR frame.
Figure 7.c Installing a PTO termination with the BSR frame.
Figure 7.d Installing a PTO termination with MOSR frame.
Figure 7.e Installing the VSS Vinyl Shield.
Figure 7.f Installing a PTO termination heat guard.
1
12”
2”
12”
12”
This section applies to installations where the direct vent termination
will be wall mounted. NOTE: If subject to a highly corrosive environment
i.e. Seaside, Montigo recommends using Stainless Steel Termination.
A termination with a built-in frame is installed during framing of a
structure.
1. Frame the termination opening to 11" x 11".
2. Install exterior sheathing to the structure framing.
3. Fasten the termination to the sheathing using a minimum of 4 screws.
MSR Frame
Termination
Termination
The VSS Termination shield is installed when the exterior of a structure
is clad with Vinyl siding. It is placed directly above, and on-center with
the termination.
Installation of termination frame at time of framing
Terminations with a MSR frame allow the installation of the frame prior
to installation of the termination.
1. Frame the termination opening to 12" x 12".
2. Secure the MSR Frame to the exterior sheathing of the structure.
3. Fastenthetermination to the MSRFrameusinga minimum of 4 screws.
1. Frame the MOSR opening to 12" x 12".
2. Fasten the MOSR frame to the interior side of the studs, concrete,
3. Insert the termination into the MOSR frame as shown here, (from
the inside) and attach to the MOSR by installing a min. quantity of 4
bolts into the threaded nuts on the MOSR Frame.
Installation of termination frame at time of framing in masonry
Terminations with a BSR frame allow the installation of the frame in
masonry prior to the installation of the termination
1. Frame the BSR opening to 12" x 12".
2. Secure the BSR Frame to the exterior sheathing of the structure.
3. Fastenthe termination to theBSR Frame using aminimum of 4 screws.
BSR Frame
MTKOG
Installing heat guards
Installing heat guards overterminations is recommended in installations
a pedestrian walkway, and may be required by code in public areas.
1. Ensure that the two long mounting brackets are facing the bottom
of the termination (See inset). This will provide more heat protection
at the top of the termination, where temperatures are highest.
2. Attach to the faceplate of the termination using four sheet metal
screws.
1
1”
11”
Framing
Exterior
Sheathing
Fastening Hard-
ware, minimum
4-screws
Framing
Exterior
Sheathing
Fastening Hardware,
minimum 4-screws
Termination
Framing
Exterior
Sheathing
Fastening Hardware,
minimum 4-screws
Exterior Vinyl
siding
Termination
VSS Vinyl shield
Installation of termination from inside structure
A Termination with a MOSR Frame is installed from the inside of the
structure. These are commonly used in high-rise construction.
MOSR Frame
Termination
12”
12”
Fastening Hardware,
minimum 4-screws
Framing,
concrete
or other
materials
Exterior
Sheathing, concrete
or other materials
16
Installation
xg0227 - 112718
Figure 8.b Top Vent Venting Graph for wall mounted terminations
Figure 8. Top Vented, wall mounted installation with 1 elbow (1 one 90° bend). The vent run
must comply with Venting Graph for Top vent, wall mounted terminations
Figure 8. Top Vented, wall mounted Multi-elbow installation. See Venting Graph for Top vent,
wall mounted terminations
Figure 8. Top Vented, wall mounted Retracted Multi-elbow installation
Selection of components and details of venting layout should adhere
to the following guidelines:
Vent terminations must not be recessed in walls or siding.
For Heat Shield requirements see Section 3-3.
Once the proposed venting layout has been determined refer to
graph to ensure the layout is acceptable.
Notes Wall Mounted Terminations: TOP VENT
All measurements for vertical or horizontal runs are measured from
center of the vent pipe.
Venting runs must fall within the limits set by the venting graph.
PRC & PFC Top Venting Graph
installation is acceptable.
TOP VENT RUN
If the vertical dimension from the hearth is 114" and the horizontal
acceptable installation.
If the vertical dimension from the hearth is 36" and the horizontal run
acceptable installation.
would not be an acceptable installation.
0
HEARTH
12
12
0
60
36
120
24
72
96
132
Vertical Height (In.)
Horizontal Run (In.)
36 60 132 15624 72 96 120 144
within non-shaded area.
within shaded area.
A
B
C
Section 3-3-1: Venting Layout: Wall Mounted Termination
Exterior
Wall
Exterior
Wall
Exterior
Wall
Hearth
Termination
Heat Shield
Min.
Min.
Min.
Rigid
Section
Rigid
Section
Flex
Section
Flex
Section
Max.
150"
Max.
126" Max.
30" Max.
Termination
Termination
Heat Shield
Heat Shield
17
Installation
xg0227 - 112718
Figure 8. Straight run, Rear Vented, wall mounted termination
Figure 8. Rear Vented, wall mounted Multi-elbow termination installation. must have a mini-
mum vertical rise of 20"
Selection of components and details of venting layout should adhere
to the following guidelines:
Vent terminations must not be recessed in walls or siding.
For Heat Shield requirements see Section 3-3.
Once the proposed venting layout has been determined refer to
graph to ensure the layout is acceptable.
Notes Wall Mounted Terminations: REAR VENT
All measurements for vertical or horizontal runs are measured from
center of the vent pipe.
Venting runs must fall within the limits set by the venting graph.
If the vertical dimension from the hearth is 114" and the horizontal
acceptable installation.
If the vertical dimension from the hearth is 66" and the horizontal run
acceptable installation.
would not be an acceptable installation.
PFC Rear Venting Graph
installation is acceptable.
REAR VENT RUN
Figure 9. Rear Vent Venting Graph for wall mounted terminations
0
HEARTH
12
12
0
60
36
120
24
72
96
132
Vertical Height (In.)
Horizontal Run (In.)
36 60 132 15624 72 96 120 144
within non-shaded area.
within shaded area.
A
BC
Hearth
Hearth
Termination
Flex or Rigid
Heat Sheild
PXT Extention
Max.
Max.
Min.
Max.
Max.
Max.
run with no vertical lift
Installation
xg0227 - 112718
Figure 8. Straight run, Rear Vented, wall mounted termination
Figure 8. Rear Vented, wall mounted Multi-elbow termination installation. must have a mini-
mum vertical rise of 26"
Selection of components and details of venting layout should adhere
to the following guidelines:
Vent terminations must not be recessed in walls or siding.
For Heat Shield requirements see Section 3-3.
Once the proposed venting layout has been determined refer to
graph to ensure the layout is acceptable.
Notes Wall Mounted Terminations: REAR VENT
All measurements for vertical or horizontal runs are measured from
center of the vent pipe.
Venting runs must fall within the limits set by the venting graph.
If the vertical dimension from the hearth is 114" and the horizontal
acceptable installation.
If the vertical dimension from the hearth is 66" and the horizontal run
acceptable installation.
would not be an acceptable installation.
PRC Rear Venting Graph
installation is acceptable.
REAR VENT RUN
Figure 9. Rear Venting Graph for wall mounted terminations
0
HEARTH
12
12
0
60
36
120
24
72
96
132
Vertical Height (In.)
Horizontal Run (In.)
36 60 132 15624 72 96 120 144
within non-shaded area.
within shaded area.
A
BC
Hearth
Hearth
Termination
Flex or Rigid
Heat Sheild
PXT Extention
Max.
Min.
Min.
Max.
Max.
Max.
run with no vertical lift
19
Installation
xg0227 - 112718
Figure 8.b Top Vent Venting Graph for wall mounted terminations
Figure 8. Top Vented, wall mounted installation with 1 elbow (1 one 90° bend). The vent run
must comply with Venting Graph for Top vent, wall mounted terminations
Figure 8. Top Vented, wall mounted Multi-elbow installation. See Venting Graph for Top vent,
wall mounted terminations
Figure 8. Top Vented, wall mounted Retracted Multi-elbow installation
Selection of components and details of venting layout should adhere
to the following guidelines:
Vent terminations must not be recessed in walls or siding.
For Heat Shield requirements see Section 3-3.
Once the proposed venting layout has been determined refer to
graph to ensure the layout is acceptable.
Notes Wall Mounted Terminations: TOP VENT
All measurements for vertical or horizontal runs are measured from
center of the vent pipe.
Venting runs must fall within the limits set by the venting graph.
Corner Top Venting Graph
installation is acceptable.
TOP VENT RUN
If the vertical dimension from the hearth is 126" and the horizontal
acceptable installation.
If the vertical dimension from the hearth is 36" and the horizontal run
acceptable installation.
would not be an acceptable installation.
0
HEARTH
12
12
0
60
36
120
24
72
96
132
Vertical Height (In.)
Horizontal Run (In.)
36 60 132 15624 72 96 120 144
within non-shaded area.
within shaded area.
A
B
C
Exterior
Wall
Exterior
Wall
Exterior
Wall
Hearth
Termination
Heat Shield
Min.
Min.
Min.
Rigid
Section
Rigid
Section
Flex
Section
Flex
Section
Max.
150"
Max.
126" Max.
30" Max.
Termination
Termination
Heat Shield
Heat Shield
20
Installation
xg0227 - 112718
Figure 8. Rear Vented, wall mounted Multi-elbow termination installation. must have a mini-
mum vertical rise of 26"
Selection of components and details of venting layout should adhere
to the following guidelines:
Vent terminations must not be recessed in walls or siding.
For Heat Shield requirements see Section 3-3.
Once the proposed venting layout has been determined refer to
graph to ensure the layout is acceptable.
Notes Wall Mounted Terminations: REAR VENT
All measurements for vertical or horizontal runs are measured from
center of the vent pipe.
Venting runs must fall within the limits set by the venting graph.
If the vertical dimension from the hearth is 114" and the horizontal
acceptable installation.
If the vertical dimension from the hearth is 66" and the horizontal run
acceptable installation.
would not be an acceptable installation.
Corner Rear Venting Graph
installation is acceptable.
REAR VENT RUN
Figure 9. Rear Vent Venting Graph for wall mounted terminations
0
HEARTH
12
12
0
60
36
120
24
72
96
132
Vertical Height (In.)
Horizontal Run (In.)
36 60 132 15624 72 96 120 144
within non-shaded area.
within shaded area.
A
B
C
Hearth
Flex or Rigid
Min.
Min.
Max.
Max.
This manual suits for next models
20
Table of contents
Other Montigo Indoor Fireplace manuals
Montigo
Montigo H38DF PFC Instruction Manual
Montigo
Montigo H38-DF Owner's manual
Montigo
Montigo MD38-DV-2 User manual
Montigo
Montigo M36PFC Wiring diagram
Montigo
Montigo HW42DF Instruction manual
Montigo
Montigo R520 Instruction manual
Montigo
Montigo RP620 Series Instruction Manual
Montigo
Montigo BF52-ST Instruction manual
Montigo
Montigo B34DV Instruction manual
Montigo
Montigo C38-BV Instruction manual
Montigo
Montigo DelRay DRL3613NI Instruction Manual
Montigo
Montigo ECONO-PLUS 36DV-TV Operating instructions
Montigo
Montigo M36PFC Wiring diagram
Montigo
Montigo Prodigy Series Instruction Manual
Montigo
Montigo Homefire plus MD34-DV-2 Owner's manual
Montigo
Montigo P52DF Manual
Montigo
Montigo MD34-BV Homefire Plus User manual
Montigo
Montigo H52-DFN User manual
Montigo
Montigo B34DV Instruction Manual
Montigo
Montigo B34DV Instruction manual
Popular Indoor Fireplace manuals by other brands
Monessen Hearth
Monessen Hearth HDV500NV/PV Installation and operating instructions
Euroheat
Euroheat 3110 Installation instructions & user manual
Cannon
Cannon Fitzroy canterbury installation instructions
Hearth Technologies
Hearth Technologies Heat-N-Glo SL-550TRS-AU Installation and operation instructions
Jøtul
Jøtul F 270 Series Installation instructions with technical data
Celsi
Celsi ULTIFLAME B-1004553 manual
Town & Country Fireplaces
Town & Country Fireplaces D2 Series Booklet
ELECTRICSUN
ELECTRICSUN ESfocar23C Installation and use manual
Napoleon
Napoleon BGNV42N Installation and operation instructions
Vermont Castings
Vermont Castings 2050 Installation and owner's guide
Monessen Hearth
Monessen Hearth CDV7 Installation and operating instructions
Febo Flame
Febo Flame F19-C-041-138 user manual