moonboon Tripod Stand 2.0 User manual

1
Brugermanual
Moonboon slyngevugge 1
User Manual
Tripod Stand 2.0
User manual
Important: Read the user manual carefully
and keep it for future use.
Tripod Stand 2.0

2
Brugermanual
Moonboon slyngevugge 2
User Manual
Tripod Stand 2.0
What is included?
1 Wooden top in walnut wood
6 tube assembly parts
3 tube assembly parts with finished ends (“feet”)
The Stand is designed specifically for the Baby Hammock and the
Cradle. Use the Stand with or without the Moonboon Motor. The Stand
has a maximum carry capacity of 28 kg (62 lbs).
The Stand is easy to assemble. No tools are needed.
Start by assembling the individual legs. Each leg has 3 tube assembly parts.
Starting with the Foot-pipe, assemble one leg at a time. 1) Insert the metal
shafts into the bearing. 2) Push the two parts together. 3) Twist into the
locked position.
Attach the legs to the wooden top assembly with the eye bolt facing
downwards. Ensure that each leg is firmly affixed and twisted into the locked
position.
Firmly place the stand on the floor with the rubber soles of the flat-bottom
feet on the floor surface. Place the legs as far apart as possible to achieve
maximum balance. Avoid stressing the structure, and do not place the legs
further apart than 121cm (3.11 feet).
With the motor – First, mount the motor to the eye bolt on the wooden top
assembly. Then mount the Baby Hammock or Cradle to the motor using the
carabiners. See the next section for details.
Without the motor. Mount the Baby Hammock or Cradle to the wooden top
assembly. See the next section for details.
3
2
1
The stand may only be placed on a
flat floor. Maximal permitted slope
of the floor is 0.15 degrees.
Requirements for flatness are max.
2 mm (1/16 inch), measured at 2
meters (6.5 feet).
4
Assembly
Please note

3
Brugermanual
Moonboon slyngevugge 3
User Manual
Tripod Stand 2.0
Mounting
Mounting a Baby Hammock/Cradle
Connect the Hammock Spring with a safety snap hook to the eye bolt on
the wooden top assembly. Do not use any chain or mounting strap above
the Baby Hammock/ Cradle.
Please read the user manual for your Baby Hammock or Cradle thor-
oughly before use.
Mounting a Baby Hammock/Cradle with Motor
The Stand is designed specifically for the Moonboon Baby Hammock
with a Motor or a Cradle with a Motor.
First, attach the Motor to the eye bolt of the Stand using a safety snap
hook. Attach the spring and then hang the Baby Hammock/Cradle un-
der the Motor, according to the product’s user manual.
Orient both snap hooks with the narrow end towards the motor. Check
that the snap hooks are hanging and locked correctly.
Keep the power supply cord away from the Baby Hammock/Cradle and
the Stand.
Please read the user manual for your Baby Hammock/Cradle and
Motor thoroughly before use.
Only use a stainless-steel safety snap
hook without coating for mounting the
Baby Hammock/Cradle in the Stand.
The Moonboon stand is designed
for the Moonboon Baby Ham-
mock, Cradle, and Motor. We can’t
guarantee that products from other
brands can be adequately mount-
ed or will function correctly with the
stand.
Please note
Please note
To avoid the Stand tipping over or tilting, never push the Baby Hammock/
Cradle back and forth or use the Baby Hammock/Cradle as a swing or toy.
Important!

4
Brugermanual
Moonboon slyngevugge 4
User Manual
Tripod Stand 2.0
Transportation
Easily disassemble the Stand for transport. Clear the parts from the eye
bolt and put the Stand on its side. Disassemble the leg for carrying.
Never move the Stand when in use or
while your baby is in the Baby Ham-
mock/Cradle.
Please note