Mooreco Visionary Move Mobile 74965 Series User manual

UPDATED AS OF:
03/02/2021
1 of 7
Part Numbers: 74950, 74950B, 74951, 74951B, 74965-XXXX, 74973-XXXX
ASSEMBLYINSTRUCTIONS
DO NOT THROW AWAY!
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
Visionary Move Mobile

UPDATED AS OF:
03/02/2021
2 of 7
PartsList Hardware
P1 - Glass Board
P2 - Leg
P3 - Horizontal Tube
P4 - Vertical Tube
P5 - Bottom Post
P6 - Tray
P7 - Top Cap
x2 A - 1/4” x 15mm x6
B - 1/4” x 50mm x8
x2
C1 - Locking Caster x2
x2
C2 - Non-Locking Caster x2
x2 D - CasterWrench x1
x1 E - AllenWrench x1
F -LockWasher x4
x1
x1

UPDATED AS OF:
03/02/2021
3 of 7
WARNINGSANDDISCLAIMERS
ADVERTENCIASYRENUNCIAS
AVERTISSEMENTS
Review full assembly instructions and
Previo a comenzar el proceso de
Avant de commencer l’ assamblage
check that all parts are present before
ensamblaje favor de revisar las
veuillez consulter les instructions
beginning assembly. Heavy or large
instrucciones y asegurarse que cuenta con
complètes et vérifier si vous avez toutes
furniture may require multiple persons in
todas las partes y materiales necesarios.
les pièces nécessaires. Ill est possible que
order to properly assemble. If you have
Es posible que los muebles grandes o
plusieurs personnes soient nécessaires
questions regarding assembly, contact
pesados, requieran mas de una persona
pour assemble des meubles grand ou
the manufacturer before continuing.
para ensamblarlos correctamente. Por
lourds. En cas de doute sur l assamblage
Damage due to incorrect assembly may
favor contacte al fabricante directamente
contactez le fabricant avant de continuer.
not be covered by warranty. Do not use
si tiene alguna duda o pregunta antes de
Les dommages encourus pendant
product unless all screws are tight. Check
continuar con el proceso de armado del
l’assamblage ne seront pas couvert par
all screws for tightness at least every
producto. La garantía no cubrirá daños
la garantie. Ne pas utiliser le produit sans
six months. If parts are broken, missing,
que ocurrieron por errores cometidos
vérifier que tous les vis soient serrées.
damaged, or worn, stop use of the product
durante el proceso de ensamblaje. Todos
Vérifiez que les vis sont serrées au moins
until repairs are made by your dealer using
los tornillos deben estar ajustados previo
tous le 6 mois. Si aucune pièce se casse,
factory authorized parts.
el uso del producto. Debe revisar los
manque, est endommagée ou usée,
tornillos periódicamente, por lo menos
arrêtez d’ utiliser de produit jusqu’à ce
cada seis meses y asegurarse de que
que le vendeur le repaire a l’aide de pièces
estén bien ajustados. Por favor detenga
autorisées par la fabricant.
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.

UPDATED AS OF:
03/02/2021
4 of 7
F
C2
P2
C1
B
P5
STEP1
Place Lock Washer on each Caster stem then screw in Casters to Leg and tighten with Caster
Wrench. Use one Locking Caster and one Non-Locking Caster per Leg. Repeat for second Leg.
STEP2
Connect Bottom Post to Legs using two screws (B) per Leg.

UPDATED AS OF:
03/02/2021
5 of 7
P3
P4
B
STEP3
ConnectVerticalandHorizontalTubesasshown.MakesurethesideholesonbothVertical
TubesareorientedthesamewayandholesonHorizontalTubesarefacingoutward.
Side Holes
STEP 4
Position frame in between Legs and secure with two screws (B) on each
side.Make sureframe isoriented correctly.

UPDATED AS OF:
03/02/2021
6 of 7
P1
STEP6
Peel off adhesive cover on all four front and back pieces of double-sided tape on frame. Place
Glass Boards by inserting bottomof each board in tray on both sides and holding flush against
eitherface of framepressing firmly into tape.
STEP5
Attach Tray to underside of frame using three screws (A).
P6
A

UPDATED AS OF:
03/02/2021
7 of 7
A
P7
STEP7
Secure boards in place by fitting Top Cap over top edge of boards and screwing into top of frame
withthreescrews (A).
THIS COMPLETES ASSEMBLY INSTRUCTION