Mooreco 90451 Series User manual

Modular Teacher Desk - Single Pedestal
UPDATED AS OF: 09/04/2019
Part Numbers: 90451-XXXX-XX / 90452-XXXX-XX
1 of 9
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!

INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
Parts
UPDATED AS OF: 09/04/2019 2 of 9
90390 - 1 Side Leg
90369 - Pedestal
58590 - Support Tube
58259 (72”)/ 58258 (60”)
- Modesty Panel
Table Top (Custom)
x1
x1
x1
x1
x1

P1 - Pedestal Box
P3 - H Support Tube
P6 - V Bracket: Inner
P7 - V Bracket: Outer
A - M6 x 42mm
A2 - M4 x 12mm
B - M6 x 12mm
C1 - Locking Caster
C2 - Caster
Tool(s):
-Allen Wrench
x1
x1
x1
x1
x8
x4
x5
x2
x2
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
Hardware
UPDATED AS OF: 09/04/2019 3 of 9
P1 - Adjustable Leg
P2 - V Bracket: Inner
A - M6 x 42mm
B - M6 x 12mm
E - Non-Locking Caster
F - Locking Caster
G - Lock Washer
Tool(s):
-Allen Wrench
-Caster Wrench
x1
x1
x2
x3
x1
x1
x2
90390 - 1 Sided Leg
P1 - Support Tube
P2 - U Clamp
A - M6 x 12mm
C - Set Screw
D - Wood Screw
Tool(s):
-Allen Wrench
x1
x2
x4
x2
x4
58590 - Support Tube
90369 - Pedestal

For full product warranty details, please visit:
Para obtener información sobre la garantía del producto, consulte este sitio (ingles):
Pour plus d’informations sur la garantie du produit, consultez ce site (anglais):
For questions on assembly or missing/damaged parts, please contact us using the
following information.
Para preguntas sobre el ensamblaje o piezas faltantes o dañadas, por favor
contáctenos usando la siguiente información.
Pour toute question sur le montage l-assamblage manquantes ou endommagées,
veuillez nous contacter en utilisant les l’information ci-dessous.
To register your product for warranty, please visit:
Para registrar la garantía del producto, vea este sitio (en ingles):
Pour enregistrer la garantie de votre produit, consultez ce site (en anglais):
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
WARRANTY
CARE & MAINTENANCE
PRODUCT REGISTRATION
UPDATED AS OF: 09/04/2019 4 of 9
Phone:
1.800.749.2258
(Monday – Friday, 8AM – 5PM
Central Time)
http://moorecoinc.com/warranty
https://moorecoinc.com/register
Email:
[e-mail]
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instruccionesyasegurarsequecuentacon
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS

STEP 1
UPDATED AS OF: 09/04/2019 5 of 9
STEP 2
Hardware Required:
-Adjustable Leg:
90390 - P1
-Non-locking Caster:
90390 - E
-Locking Caster:
90390 - F
-Lock Washer x2:
90390 - G
Tool(s) Required:
-Caster Wrench
Attach two casters (E,F) to Adjustable Leg (P1)with Caster
Wrench included. Locking Caster installed in front.
Hardware Required:
-M4 x 12mm x4
90369 - A2
-Locking Caster x2
90369 - C1
-Caster x2
90369 - C2
Tool(s) Required:
-Allen Wrench
Attach all four casters (C1,C2) to bottom of Pedestal Box (P1) by sliding
in brackets and tightening with screw (A2). Do not install casters while
resting pedestal on sliding brackets as this may cause brackets to
bend. Locking Casters installed in front.

STEP 3
UPDATED AS OF: 09/04/2019 6 of 9
STEP 4
Hardware Required:
-V-Bracket: Outer
90369 - P7
-V-Bracket: Inner x2
90390 - P2
90369 - P6
-M6 x12mm x6
90369 - B x5
90390 - B x1
Tool(s) Required:
-Allen Wrench
ConnectV-bracketOuter(P7) tobackofpedestalwithtwo screws
(B). For left-handed desk (see cover page) install as shown. For
right-handed desk install on opposite side of pedestal. Connect
V-bracket Inners (P2, P6) to Modesty Panel with two screws each
(B). Keep top screw 3 holes or less from edge of panel to use desk
at lowest setting. Circular holes at bottom of brackets should
face down.
Slide modesty panel V-bracket Inners into outer brackets
on pedestal and leg. Secure modesty panel in place with
two screws (B) inserted through bottom of brackets.
Hardware Required:
-M6 x 12mm x2
90390 - B
Tool(s) Required:
-Allen Wrench

STEP 5
UPDATED AS OF: 09/04/2019 7 of 9
STEP 6
After removing all four screws from leg, raise to highest setting.
Replace single screw to hold leg in place. Next adjust pedestal
bracket height by pressing levers on both sides while lifting.
Raise bracket to approximate height of leg. Set H-Support on
top of bracket. Make sure holes are oriented as shown. With
H-Support resting on bracket lower bracket slightly to be even
in height with leg.
Loosen set screw (C) on sliding outer member of Support Tube
(P1). Fasten one side of tube to side of leg with screws (A) then
after adjusting tube to appropriate length, fasten opposite side
of tube to H-Support with same screws. Check Support Tube
with a level and adjust the pedestal sliding bracket height as
needed. Once level, retighten set screw on Support Tube.
Hardware Required:
-H-Support Tube
90369 - P3
Tool(s) Required:
-Allen Wrench
Hardware Required:
-Support Tube
58590 - P1
-M6 x 12mm x4
58590 - A
Tool(s) Required
-Allen Wrench
-Level

STEP 7
UPDATED AS OF: 09/04/2019 8 of 9
STEP 8
Set Table Top into place by aligning threaded inserts on
undersideof table withholesin H-Support tubeandAdjustable
Leg. Insert screws (A) up through holes and hand tighten all
before tightening further with allen wrench. Be sure grommet
holes are positioned correctly.
With two or more people, carefully lower table to desired height. One
person will need to apply pressure to table surface while the other
presses both levers on pedestal bracket. All screws will need to be
removed from leg to allow for adjustment. After reaching preferred
height, replace all screws in leg and recheck surface is level. Any final
height adjustments can be made with pedestal.
Hardware Required:
-M6 x 42mm x10
90390 - A x2
90369 - A x8
Tool(s) Required:
-Allen Wrench
Tool(s) Required:
-Allen Wrench

STEP 9
Install U-Clamps by sliding over Support Tube and securing with two
wood screws each (D). Screws are driven directly into underside of ta-
ble. Position clamps approximately half-way along each sliding tube.
THIS COMPLETES ASSEMBLY INSTRUCTION
Hardware Required:
-U-Clamp x2
58590 - P2
-Wood Screw x4
58590 - D
Tool(s) Used
-Electric Drill (recommended)
UPDATED AS OF: 09/04/2019 9 of 9